[netdevice] Allow link layer to report broadcast/multicast packets via pull()
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[process] Pass containing object pointer to process step() methods
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hermon] Remove temporary workaround for missing BOFM mport support
This reverts commit 15c1200 ("[hermon] Work around missing mport
support in current BOFM implementations").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hermon] Work around missing mport support in current BOFM implementations
Current BOFM versions are unable to create entries with mport>1, which
means that only the port 1 MAC address can be explicitly specified.
Work around this by using the provided MAC address as a base address
for all subsequent ports. For example, if BOFM assigns the address
00:1A:64:76:00:09 for port 1
then we will assign the addresses
00:1A:64:76:00:09 for port 1
00:1A:64:76:00:0a for port 2
Future BOFM versions that may correctly support mport will work with
this scheme without modification provided that the BOFM entries are
created in increasing order of mport. Since BOFM tools tend to
generate entries in increasing order (of slot, port, etc), this is not
an unreasonable compromise.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[forcedeth] Never change the NVREG_TRANSMITPOLL_MAC_ADDR_REV flag
iPXE operates the forcedeth NIC in promiscuous mode, and never changes
the unicast MAC address filter registers. We should not therefore set
the flag indicating (to other drivers loaded later) that the MAC
address order has already been corrected.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[forcedeth] Remove software unicast MAC address filter
The forcedeth driver currently implements unicast MAC address
filtering in software. This is almost invariably the wrong thing to
do (since the network stack must already be able to cope with unwanted
packets) and it breaks FCoE (which requires the card to operate in
promiscuous mode).
Also, the implementation is buggy: is_local_ether_addr() is used to
check for a locally-assigned Ethernet address (not to check for a
unicast address), and the current link-layer address is in
netdev->ll_addr, not netdev->hw_addr.
Fix by removing this code.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[forcedeth] Avoid unused-but-set variable warning in gcc 4.6
Avoid unused-but-set variable warning in gcc 4.6 which was introduced
by commit 9215b7f ("[forcedeth] Clear the MII link status register on
link status changes").
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Formalise notion of setting applicability
Expose a function setting_applies() to allow a caller to determine
whether or not a particular setting is applicable to a particular
settings block.
Restrict DHCP-backed settings blocks to accepting only DHCP-based
settings.
Restrict network device settings blocks to accepting only DHCP-based
settings and network device-specific settings such as "mac".
Inspired-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
From a cursory examination, it appears as though the calculation of
tx_available is redundant, since eepro_transmit() waits for transmit
completion before returning anyway.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[e1000] Remove unused variable when ICR register is simply cleared
On reset and close, the ICR register is read to clear any pending
interrupts, but the value is simply ignored. Avoid assigning the
value to a variable, to inhibit a warning from gcc 4.6.
Also fix a potential race condition in reset routines which clear
interrupts before disabling them.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[igbvf] Remove some unused Linux-specific portions of igbvf.h
These unused portions trigger a compiler warning under gcc 4.6, due to
the ambiguity over the "page" field in struct igbvf_buffer.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a virtual environment such as qemu, we can legitimately receive
packets less than 64 bytes in length, such as ARP replies. These are
currently discarded, causing most IPv4 communication to fail.
Fix by ignoring the RFDShort bit when receiving packets.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When chainloading rtl8139.pxe from an old Etherboot rtl8139.zrom, iPXE
can end up misreading the first word of the MAC address from the
EEPROM as being all zeroes. This is presumably because Etherboot has
left the serial EEPROM in an unexpected state.
Fix by using the chip select line to reset the SPI device before we
start accessing it.
Reported-by: Mandar U Jog <mandarjog@gmail.com>
Tested-by: Mandar U Jog <mandarjog@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The default initiator IQN is "iqn.2000-09.org.etherboot:UNKNOWN".
This is problematic for two reasons:
a) the etherboot.org domain (and hence the associated IQN namespace)
is not under the control of the iPXE project, and
b) some targets (correctly) refuse to allow concurrent connections
from different initiators using the same initiator IQN.
Solve both problems by changing the default initiator IQN to be
iqn.2010-04.org.ipxe:<hostname> if a hostname is set, or
iqn.2010-04.org.ipxe:<uuid> if no hostname is set.
Explicit initiator IQNs set via DHCP option 203 are not affected by
this change.
Unfortunately, this change is likely to break some existing
configurations, where ACL rules have been put in place referring to
the old default initiator IQN. Users may need to update ACLs, or
force the use of the old IQN using an iPXE script line such as
set initiator-iqn iqn.2000-09.org.etherboot:UNKNOWN
or a dhcpd.conf option such as
option iscsi-initiator-iqn "iqn.2000-09.org.etherboot:UNKNOWN"
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some operating environments require (or at least prefer) that we do
not perform our own PCI bus scan, but deal only with specified
devices. Modularise the PCI core to allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pci] Use single "busdevfn" field in struct pci_device
Merge the "bus" and "devfn" fields into a single "busdevfn" field, to
match the format used by the majority of external code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On 64-bit builds, MLX_DECLARE_STRUCT() produces a structure that is
always a multiple of 64 bits long, causing the HCR structure to be
over-length by one dword. This in turn causes hermon_cmd() to write
beyond the end of the HCR, which causes commands to fail.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid memory leak of untreated events by having circular event queue
operation.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown