[makefile] Add -Wformat-nonliteral as an extra warning category
-Wformat-nonliteral is not enabled by -Wall and needs to be explicitly
specified.
Modified the few files that use nonliteral format strings to work with
this new setting in place.
Inspired by a patch from Carl Karsten <carl@personnelware.com> and an
identical patch from Rorschach <r0rschach@lavabit.com>.
[efi] Add EFI headers from the EFI Development Kit (edk2)
The intention is to include near-verbatim copies of the EFI headers
required by gPXE. This is achieved using the import.pl script in
src/include/gpxe/efi.
Note that import.pl will modify any #include lines in each imported
header to reflect its new location within the gPXE tree. It will also
tidy up the file by removing carriage return characters and trailing
whitespace.
[i2c] Generalise i2c bit-bashing support to addressless devices
Some devices (e.g. the Atmel AT24C11) have no concept of a device
address; they respond to every device address and use this value as
the word address. Some other devices use part of the device address
field to extend the word address field.
Generalise the i2c bit-bashing support to handle this by defining the
device address length and word address length as properties of an i2c
device. The word address is assumed to overflow into the device
address field if the address used exceeds the width of the word
address field.
Also add a bus reset mechanism. i2c chips don't usually have a reset
line, so rebooting the host will not clear any bizarre state that the
chip may be in. We reset the bus by clocking SCL until we see SDA
high, at which point we know we can generate a start condition and
have it seen by all devices. We then generate a stop condition to
leave the bus in a known state prior to use.
Finally, add some extra debugging messages to i2c_bit.c.
[compiler] Allow for selective disabling of debug levels at runtime
The usefulness of DBGLVL_IO is limited by the fact that many cards
require large numbers of uninteresting I/O reads/writes at device
probe time, typically when driving a bit-bashing I2C/SPI bus to read
the MAC address.
This patch adds the DBG_DISABLE() and DBG_ENABLE() macros, which can
be used to temporarily disable and re-enable selected debug levels.
Note that debug levels must still be enabled in the build in order to
function at all: you can't use DBG_ENABLE(DBGLVL_IO) in an object
built with DEBUG=object:1 and expect it to do anything.
[undi] Fill in ProtType correctly in PXENV_UNDI_ISR
Determine the network-layer packet type and fill it in for UNDI
clients. This is required by some NBPs such as emBoot's winBoot/i.
This change requires refactoring the link-layer portions of the
gPXE netdevice API, so that it becomes possible to strip the
link-layer header without passing the packet up the network stack.
[pcbios] Support arbitrary splits of the e820 memory map
Allow for an arbitrary number of splits of the system memory map via
INT 15,e820.
Features of the new map-mangling algorithm include:
Supports random access to e820 map entries.
Requires only sequential access support from the underlying e820
map, even if our caller uses random access.
Empty regions will always be stripped.
Always terminates with %ebx=0, even if the underlying map terminates
with CF=1.
Allows for an arbitrary number of hidden regions, with underlying
regions split into as many subregions as necessary.
Total size increase to achieve this is 193 bytes.
[retry] Added configurable timeouts to retry timer
New min_timeout and max_timeout fields in struct retry_timer allow
users of this timer to set their own desired minimum and maximum
timeouts, without being constrained to a single global minimum and
maximum. Users of the timer can still elect to use the default global
values by leaving the min_timeout and max_timeout fields as 0.
[autoboot] Retain initial-slash (if present) when constructing TFTP URIs
When we boot from a DHCP-supplied filename, we previously relied on
the fact that the current working URI is set to tftp://[next-server]/
in order to resolve the filename into a full tftp:// URI. However,
this process will eliminate the distinction between filenames with and
without initial slashes:
cwuri="tftp://10.0.0.1/" filename="vmlinuz" => URI="tftp://10.0.0.1/vmlinuz"
cwuri="tftp://10.0.0.1/" filename="/vmlinuz" => URI="tftp://10.0.0.1/vmlinuz"
This distinction is important for some TFTP servers. We now
explicitly construct a string of the form
"tftp://[next-server]/filename"
so that a filename with an initial slash will result in a URI
containing a double-slash, e.g.
"tftp://10.0.0.1//vmlinuz"
The TFTP code always strips a single initial slash, and so ends up
presenting the correct path to the server.
URIs entered explicitly by users at the command line must include a
double slash if they want an initial slash presented to the TFTP
server:
"kernel tftp://10.0.0.1/vmlinuz" => filename="vmlinuz"
"kernel tftp://10.0.0.1//vmlinuz" => filename="/vmlinuz"
In tg3_chip_reset(), the PCI_EXPRESS change is taken from the Linux
tg3 driver. I am not sure what exactly it does (it is not documented
in the Linux driver), but it is necessary for the NIC to work
correctly.
[iSCSI] Support Windows Server 2008 direct iSCSI installation
Add yet another ugly hack to iscsiboot.c, this time to allow the user to
inhibit the shutdown/removal of the iSCSI INT13 device (and the network
devices, since they are required for the iSCSI device to function).
On the plus side, the fact that shutdown() now takes flags to
differentiate between shutdown-for-exit and shutdown-for-boot means that
another ugly hack (to allow returning via the PXE stack on BIOSes that
have broken INT 18 calls) will be easier.
I feel dirty.
We can just treat all non-kernel images as initrds, which matches our
behaviour for multiboot kernels. This allows us to eliminate initrd as
an image type, and treat the "initrd" command as just another synonym for
"imgfetch".
This commit implements GDB over UDP. Using UDP is more complex than
serial and has required some restructuring.
The GDB stub is now built using one or both of GDBSERIAL and GDBUDP
config.h options.
To enter the debugger, execute the gPXE shell command:
gdbstub <transport> [<options>...]
Where <transport> is "serial" or "udp". For "udp", the name of a
configured network device is required:
gdbstub udp net0
The GDB stub listens on UDP port 43770 by default.
[legacy] Align legacy drivers' __shared data to the maximum possible
Some drivers that still use the legacy-driver wrapper (tg3 in particular)
apparently do not specify their alignment constraints properly. This
hack forces any __shared data to be maximally aligned.
Note that this provides only 16-byte alignment; it is not possible to
request alignment to any greater than 16 bytes using
__attribute__((aligned)), since the relocation code will preserve only 16
byte alignment (and operation under -DKEEP_IT_REAL cannot preserve more
that 16 byte alignment).
Idea proposed by Tim Hockin <thockin@google.com>
[udp] Verify local socket address (if specified) for UDP sockets
UDP sockets can be used for multicast, at which point it becomes
plausible that we could receive packets that aren't destined for us
but that still match on a port number.
[ELF] Add ability to boot ELF images generated by wraplinux and mkelfImage
Delete ELF as a generic image type. The method for invoking an
ELF-based image (as well as any tables that must be set up to allow it
to boot) will always depend on the specific architecture. core/elf.c
now only provides the elf_load() function, to avoid duplicating
functionality between ELF-based image types.
Add arch/i386/image/elfboot.c, to handle the generic case of 32-bit
x86 ELF images. We don't currently set up any multiboot tables, ELF
notes, etc. This seems to be sufficient for loading kernels generated
using both wraplinux and coreboot's mkelfImage.
Note that while Etherboot 5.4 allowed ELF images to return, we don't.
There is no callback mechanism for the loaded image to shut down gPXE,
which means that we have to shut down before invoking the image. This
means that we lose device state, protection against being trampled on,
etc. It is not safe to continue afterwards.
[iSCSI] Produce meaningful errors on login failure
Return the most appropriate of EACCES, EPERM, ENODEV, ENOTSUP, EIO or
EINVAL depending on the exact error returned by the target, rather than
just always returning EPERM.
Also, ensure that error strings exist for these errors.
[SMBIOS] Interpret UUIDs as being in network-endian order
Various specification documents disagree about the byte ordering of
UUIDs. However, SMBIOS seems to use the standard in which everything is
in network-endian order.
This doesn't affect anything sent on the wire; only what gets printed on
the screen when the "uuid" variable is displayed.
[MTNIC] Minor cleanups of vendor-provided driver for Mellanox 10GigE cards
Drivers are not allowed to call printf(). Converted eprintf() to DBG(),
and removed spurious startup banner.
Fixed hardcoded inclusion of little_bswap.h
Use EIO rather than 1 as an error number.
Add ability for network devices to flag link up/down state to the
networking core.
Autobooting code will now wait for link-up before attempting DHCP.
IPoIB reflects the Infiniband link state as the network device link state
(which is not strictly correct; we also need a succesful IPoIB IPv4
broadcast group join), but is probably more informative.
[Infiniband] Add preliminary multiple port support for Hermon cards
Infiniband devices no longer block waiting for link-up in
register_ibdev().
Hermon driver needs to create an event queue and poll for link-up events.
Infiniband core needs to reread MAD parameters when link state changes.
IPoIB needs to cope with Infiniband link parameters being only partially
available at probe and open time.
The PXE spec is (as usual) unclear on precisely when ProxyDHCPREQUESTs
should be issued. We adapt the following, slightly paranoid approach:
If an offer contains an IP address, then it is a normal DHCPOFFER.
If an offer contains an option #60 "PXEClient", then it is a
ProxyDHCPOFFER. Note that the same packet can be both a normal
DHCPOFFER and a ProxyDHCPOFFER.
After receiving the normal DHCPACK, if we have received a
ProxyDHCPOFFER, we unicast a ProxyDHCPREQUEST back to the ProxyDHCP
server on port 4011. If we time out waiting for a ProxyDHCPACK, we
treat this as a non-fatal error.
[PXEXT] Change the PXE return code for EWOULDBLOCK
Change the PXE return code for EWOULDBLOCK from PXENV_STATUS_FAILURE
to PXENV_STATUS_TFTP_OPEN. This code is only used by the FILE_READ
PXEXT call, and is necessary to distinguish "error" from "no data" in
that call.
(The only other nonblocking call is UDP_READ, where the caller doesn't
care about the distinction, however, gPXE doesn't use EWOULDBLOCK
internally to represent this condition in that code.)