Replace a printf with a DBG in timer_rtdsc.c
Replace a printf in timer.c with assert
Return proper error codes from timer drivers
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Timer subsystem initialization code in core/timer.c
Split the BIOS and RTDSC timer drivers from i386_timer.c
Split arch/i386/firmware/pcbios/bios.c into the RTSDC
timer driver and arch/i386/core/nap.c
Split the headers properly:
include/unistd.h - delay functions to be used by the
gPXE core and drivers.
include/gpxe/timer.h - the fimer subsystem interface
to be used by the timer drivers
and currticks() to be used by
the code gPXE subsystems.
include/latch.h - removed
include/timer.h - scheduled for removal. Some driver
are using currticks, which is
only for core subsystems.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
RFC 4390 provides for the DHCP client identifier to contain the link-layer
hardware type and MAC address when the MAC address exceeds 16 bytes.
However, the hardware type field is only 8 bits; we were assuming 16 bits.
[Infiniband] Add preliminary support for multi-port devices.
Arbel and Hermon cards both have multiple ports. Add the
infrastructure required to register each port as a separate IB
device. Don't yet register more than one port, since registration
will currently fail unless a valid link is detected.
Use ib_*_{set,get}_{drv,owner}data wrappers to access driver- and
owner-private data on Infiniband structures.
Pull out common code for handling management datagrams from arbel.c
and hermon.c into infiniband.c.
Add port number to struct ib_device.
Add open(), close() and mad() methods to struct ib_device_operations.
As written, if the if the UNDI ISR call clobbers the upper halves of
any of the GPRs (which by convention it is permitted to do, and by
paranoia should be expected to do) then nothing in the interrupt
handler will recover the state.
Additionally, save/restore %fs and %gs out of sheer paranoia - it's a
cheap enough operation, and may prevent problems due to poorly written
UNDI stacks.
Since we don't know what the UNDI code does, it is safest to
save/restore %eflags even though the lower half of %eflags is
automatically saved by the interrupt itself.
As written, if the if the UNDI ISR call clobbers the upper halves of
any of the GPRs (which by convention it is permitted to do, and by
paranoia should be expected to do) then nothing in the interrupt
handler will recover the state.
Additionally, save/restore %fs and %gs out of sheer paranoia - it's a
cheap enough operation, and may prevent problems due to poorly written
UNDI stacks.
Allow port numbers in iSCSI redirection.
Wait for SCSI status, not just the final data-in (which may be followed
by an explicit SCSI Response PDU if the S bit is not set).
Unconditionally set utility program variables in Makefile to allow CROSS_COMPILE to work.
stappers and xl0 pointed out that gnu make sets some variables, so ?=
is ineffective in some cases where we use it.. Cross-compilation
requires that some variables can be overridden in the
src/$(ARCH)/Config file, so include that file _after_ utility program
variables are set.
From: Geert Stappers <stappers@stappers.nl>
To: etherboot-developers@lists.sourceforge.net
Subject: [Etherboot-developers] 3c90x polling again [patch]
Date: Thu, 29 Nov 2007 09:22:36 +0100
User-Agent: Mutt/1.5.16 (2007-06-11)
Hello,
gPXE didn't work on 3COM 905C Tornado cards for me.
It did transmit the DHCP request, but it didn't see the DHCP offer.
Adding debug print statements allready solved the problem.
Attached is a patch that has a cleaner delay then print statements.
The core of it is
- for(i=0;i<40000;i++);
+ mdelay(1);
There was no research if the change is about a longer delay
or about code NOT being optimized away. It works for me :-)
Cheers
Geert Stappers
Overwrite the device descriptor's IRQ number with whatever the legacy
driver's probe() routine fills in in nic->irqno. This is so that
non-interrupt-capable legacy drivers which set nic->irqno=0 will end
up reporting IRQ#0 via PXENV_UNDI_GET_INFORMATION; this in turn means
that the calling PXE NBP will (should) hook the timer interrupt, and
everything will sort of work.
Correct e1000 interrupt routine to enable on 1 disable on 0. duh.
The e1000_irq() routine should (per mcb30) do enable on non-zero,
disable on zero. This is not consistent in all drivers, so I'll
wait to update it when doing a global sweep.
Alexey Zaytsev