This previously unsupported NIC variant was was found to work using
the current driver:
PCI_ROM(0x13f0, 0x0200, "ip100a", "IC+ IP100A"),
Signed-off-by: Marty Connor <mdc@etherboot.org>
[scsi] Cope with targets that send multiple CHECK CONDITIONS at power-on
Some targets send a spurious CHECK CONDITION message in response to
the first SCSI command. We issue (and ignore the status of) an
arbitary harmless SCSI command (a READ CAPACITY (10)) in order to draw
out this response.
The Solaris Comstar target seems to send more than one spurious CHECK
CONDITION response. Attempt up to SCSI_MAX_DUMMY_READ_CAP dummy READ
CAPACITY (10) commands before assuming that error responses are
meaningful.
Problem reported by Kristof Van Doorsselaere <kvandoor@aserver.com>
and Shiva Shankar <802.11e@gmail.com>.
[etherfabric] Make use of pci_bar_start() 64-bit clean
Driver was storing the result of pci_bar_start() and pci_bar_size() in
an int, rather than an unsigned long.
(Bug was introduced in the vendor's tree in commit eac85cd "Port
etherfabric driver to net_device api".)
adjust_pci_device() has historically enabled bus-mastering and I/O
cycles, but has never previously needed to enable memory cycles. Some
EFI systems seem not to enable memory cycles by default, so add that
to the list of PCI command register bits that we force on.
[e1000] Use PCI_BASE_ADDRESS_* symbols instead of integers
When compiling for the Linux kernel, PCI_BASE_ADDRESS_0 == 0, and
PCI_BASE_ADDRESS_1 == 1. This is not so when compiling for gPXE. We
must use the symbolic names rather than integers to get the correct
values.
Bug identified and patch supplied by:
George Chou <george.chou@advantech.com>
[hermon] Fix permissions broken in 3a799e9 ("Add PCI ID for ConnectX QDR card")
The patch file supplied for commit 3a799e9 ("[hermon] Add PCI ID for
ConnectX QDR card") accidentally marked drivers/infiniband/hermon.c as
being executable.
This driver is based on Stefan Hajnoczi's summer work, which
is in turn based on version 1.01 of the linux b44 driver.
I just assembled the pieces and fixed/added a few pieces
here and there to make it work for my hardware.
The most major limitation is that this driver won't work
on systems with >1GB RAM due to the card not having enough
address bits for that and gPXE not working around this
limitation.
Still, other than that the driver works well enough for
at least 2 users :) and the above limitation can always
be fixed when somebody wants it bad enough :)
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
[i386] Change [u]int32_t to [unsigned] int, rather than [unsigned] long
This brings us in to line with Linux definitions, and also simplifies
adding x86_64 support since both platforms have 2-byte shorts, 4-byte
ints and 8-byte long longs.
[infiniband] Respect hop pointer when building directed route SMP return path
The return path in directed route SMPs lists the egress ports in order
from SM to node, rather than from node to SM.
To write to the correct offset within the return path, we need to
parse the hop pointer. This is held within the class-specific data
portion of the MAD header, which was previously unused by us and
defined to be a uint16_t. Define this field to be a union type; this
requires some rearrangement of ib_mad.h and corresponding changes to
ipoib.c.
[linda] Add support for QLogic 7220-based Infiniband HCAs
These cards very nearly support our current IB Verbs model. There is
one minor difference: multicast packets will always be delivered by
the hardware to QP0, so the driver has to redirect them to the
appropriate QP. This means that QP owners may see receive completions
for buffers that they never posted. Nothing in our current codebase
will break because of this.
[infiniband] Add raw packet parser and constructor
This can be used with cards that require the driver to construct and
parse packet headers manually. Headers are optionally handled
out-of-line from the packet payload, since some such cards will split
received headers into a separate ring buffer.
Some Infiniband cards will not be as accommodating as the Arbel and
Hermon cards in providing enough space for us to push a fake extra
header at the start of the received packet. We must therefore make do
with squeezing enough information to identify source and destination
addresses into the two bytes of padding within a genuine IPoIB
link-layer header.
[infiniband] Split subnet management agent client out into ib_smc.c
Not all Infiniband cards have embedded subnet management agents.
Split out the code that communicates with such an embedded SMA into a
separate ib_smc.c file, and have drivers call ib_smc_update()
explicitly when they suspect that the answers given by the embedded
SMA may have changed.
[infiniband] Pass address vector in receive completions
Receive completion handlers now get passed an address vector
containing the information extracted from the packet headers
(including the GRH, if present), and only the payload remains in the
I/O buffer.
This breaks the symmetry between transmit and receive completions, so
remove the ib_completer_t type and use an ib_completion_queue_operations
structure instead.
Rename the "destination QPN" and "destination LID" fields in struct
ib_address_vector to reflect its new dual usage.
Since the ib_completion structure now contains only an IB status code,
("syndrome") replace it with a generic gPXE integer status code.
[infiniband] Flush uncompleted work queue entries at QP teardown
Avoid leaking I/O buffers in ib_destroy_qp() by completing any
outstanding work queue entries with a generic error code. This
requires the completion handlers to be available to ib_destroy_qp(),
which is done by making them static configuration parameters of the CQ
(set by ib_create_cq()) rather than being provided on each call to
ib_poll_cq().
This mimics the functionality of netdev_{tx,rx}_flush(). The netdev
flush functions would previously have been catching any I/O buffers
leaked by the IPoIB data queue (though not by the IPoIB metadata
queue).
Add the simplified ne2k_isa driver. It is just a selective copy+paste
of the relevant parts from ns8390.c plus a little trivial hacking to
make it actually work.
It is true that the code is pretty ugly, but:
a) ns8390.c is worse
b) It is only 372 lines and no #ifdefs
c) It works both in qemu/bochs and in real hardware
and we all know it is easier to cleanup working code
Hope someone will find the time to rewrite this driver properly,
but until then at least for me this is an ok solution.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Halting the PEGs breaks platforms where there is sideband access to
the NIC (e.g. HP machines using iLO). (We have to retain the
unhalting code because on some other platforms (e.g. IBM blades with
BOFM) the pre-PXE firmware must halt the PEGs to avoid issues with the
BIOS rereading via the expansion ROM BAR.)
[phantom] Allow for PXE boot to be enabled/disabled on a per-port basis
This is something of an ugly hack to accommodate an OEM requirement.
The NIC has only one expansion ROM BAR, rather than one per port. To
allow individual ports to be selectively enabled/disabled for PXE boot
(as required), we must therefore leave the expansion ROM always
enabled, and place the per-port enable/disable logic within the gPXE
driver.
The Phantom firmware selectively disables PCI functions based on the
board type, with the end result that we see one PCI function for each
network port. This allows us to eliminate the code for reading from
flash and, more importantly, removes knowledge of the board type magic
number from the gPXE driver.
[settings] Add the notion of a "tag magic" to numbered settings
Settings can be constructed using a dotted-decimal notation, to allow
for access to unnamed settings. The default interpretation is as a
DHCP option number (with encapsulated options represented as
"<encapsulating option>.<encapsulated option>".
In several contexts (e.g. SMBIOS, Phantom CLP), it is useful to
interpret the dotted-decimal notation as referring to non-DHCP
options. In this case, it becomes necessary for these contexts to
ignore standard DHCP options, otherwise we end up trying to, for
example, retrieve the boot filename from SMBIOS.
Allow settings blocks to specify a "tag magic". When dotted-decimal
notation is used to construct a setting, the tag magic value of the
originating settings block will be ORed in to the tag number.
Store/fetch methods can then check for the magic number before
interpreting arbitrarily-numbered settings.
This interface provides access to firmware settings (e.g. MAC address)
that will apply to all drivers loaded for the duration of the current
system boot.
[phantom] Unhalt/halt all PEGs during driver startup/shutdown
A hardware bug means that reads through the expansion ROM BAR can
return corrupted data if the PEGs are running. This breaks platforms
that re-read the expansion ROM after invoking gPXE code, such as IBM
blade servers.
Halt PEGs during driver shutdown, and unhalt PEGs during driver
startup if we detect that this is not the first startup since
power-on.
[phantom] Change register space abstraction to match other drivers
Most other Phantom drivers define a register space in terms of a 64M
virtual address space. While this doesn't map in any meaningful way
to the actual addresses used on the latest cards, it makes maintenance
easier if we do the same.
The virtnet_transmit() logic for waiting the packet to be transmitted is
reversed: we can't wait the packet to be transmitted if we didn't kick()
the ring yet. The vring_more_used() while loop logic is reversed also,
that explains why the code works today.
The current code risks trying to free a buffer from the used ring
when none was available, that will happen most times because KVM
doesn't handle the packet immediately on kick(). Luckily it was working
because it was unlikely to have a buffer still queued for transmit when
virtnet_transmit() was called.
Also, adds a BUG_ON() to vring_get_buf(), to catch cases where we try
to free a buffer from the used ring when there was none available.
Patch for Etherboot. gPXE has the same problem on the code, but I hadn't
a chance to test gPXE using virtio-net yet.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
[netdevice] Change link-layer push() and pull() methods to take raw types
EFI requires us to be able to specify the source address for
individual transmitted packets, and to be able to extract the
destination address on received packets.
Take advantage of this to rationalise the push() and pull() methods so
that push() takes a (dest,source,proto) tuple and pull() returns a
(dest,source,proto) tuple.
[netdevice] Split multicast hashing out into an mc_hash method
Multicast hashing is an ugly overlap between network and link layers.
EFI requires us to provide access to this functionality, so move it
out of ipv4.c and expose it as a method of the link layer.
Itay Gazit