[intel] Remove hardcoded offsets for descriptor ring registers
The Intel 10 Gigabit NICs use the same simplified (aka "legacy")
descriptor format and the same layout for descriptor register blocks
as the Intel 1 Gigabit NICs. The offsets of the descriptor register
blocks are not the same.
Simplify reuse of the existing code by removing all hardcoded offsets
for registers within descriptor register blocks, and ensuring that all
offsets are calculated using the descriptor register block base
address provided via intel_init_ring().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid using UINT16 and similar typedefs, which are non-standard in the
iPXE codebase and generate conflicts when trying to include any of the
EFI headers.
Also fix trailing whitespace in the affected files, to prevent
complaints from git.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove macros which aren't used anywhere in the driver, and which
conflict with macros of the same name used in the EFI headers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove macros which aren't used anywhere in the driver, and which
conflict with macros of the same name used in the EFI headers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iBFT NIC section has a VLAN field which must be filled in so that
iSCSI booting works over VLANs.
Unfortunately it is unclear from the IBM specification linked in
ibft.c whether the VLAN field is just the 802.1Q VLAN Identifier or
the full 802.1Q TCI. For now just fill in the VID, the Priority Code
Point and Drop Eligible Indicator could be set in the future if it
turns out they should be present too.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[forcedeth] Increase TX ring size to prevent dropped packets
Commit 947976d ("[netdevice] Do not force a poll on net_tx()")
requires network devices to have TX rings that are sufficiently large
to allow a transmitted response to all packets received during a
single poll.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Poll RX queue if hardware reports RX overflow
The Intel NIC emulation in some versions of VMware seems to suffer
from a flaw whereby the Interrupt Cause Register (ICR) fails to assert
the usual "packet received" bit (ICR.RXT0) if a receive overflow
(ICR.RXO) has also occurred.
Work around this flaw by polling for completed descriptors whenever
either ICR.RXT0 or ICR.RXO is asserted.
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Debugged-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Tested-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipoib] Expose Ethernet-compatible eIPoIB link-layer addresses and headers
Almost all clients of the raw-packet interfaces (UNDI and SNP) can
handle only Ethernet link layers. Expose an Ethernet-compatible link
layer to local clients, while remaining compatible with IPoIB on the
wire. This requires manipulation of ARP (but not DHCP) packets within
the IPoIB driver.
This is ugly, but it's the only viable way to allow IPoIB devices to
be driven via the raw-packet interfaces.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Force EEPROM CS low before disabling EEPROM access mode
Some RTL8169 cards seem to drive the EEPROM CS line high (i.e. active)
when 9346CR.EEM is set to "normal operating mode", with the result
that the CS line is never deasserted. The symptom of this is that the
first read from the EEPROM will work, while all subsequent reads will
return garbage data.
Reported-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Forcibly enable advertisement of 1000Mbps speeds
Some RTL8169 cards (observed with an RTL8169SC) power up advertising
only 100Mbps, despite being capable of 1000Mbps. Forcibly enable
advertisement of 1000Mbps on any RTL8169-like card.
This change relies on the assumption that the CTRL1000 register will
not exist on 100Mbps-only RTL8169 cards such as the RTL8101.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Enable DAC only when built as a 64-bit binary
Some RTL8169 cards (observed with an RTL8169SC) crash and burn if DAC
is enabled, even if only 32-bit addresses are used. Observed
behaviour includes system lockups and repeated transmission of garbage
data onto the wire.
This seems to be a known problem. The Linux r8169 driver disables DAC
by default and provides a "use_dac" module parameter.
There appears to be no known test for determining whether or not DAC
will work. As a workaround, enable DAC only if we are built as as
64-bit binary. This at least eliminates the problem in the common
case of a 32-bit build, which will never use 64-bit addresses anyway.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Use read-modify-write to check for C+ Command register
Some bits in the C+ Command register are always one. Testing for the
presence of the register must allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with
TCR.MXDMA set to 16 bytes. While this does not prevent proper
operation, it almost certainly degrades performance.
Fix by explicitly setting TCR.MXDMA to "unlimited".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Use explicit values for RCR.RXFTH and RCR.MXDMA
Some RTL8169 cards (observed with an RTL8169SC) power up with invalid
values in RCR.RXFTH and RCR.MXDMA, causing receive DMA to fail. Fix
by setting explicit values for both fields.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Always set high dword of ring address registers
Some RTL8169 cards (observed with an RTL8169SC) power up with garbage
values in the ring address registers, and do not clear the registers
on reset.
Fix by always setting the high dword of the ring address registers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Change the DMA alignment from 4096 bytes to 16 bytes, to conserve
available DMA memory. The hardware doesn't have any specific
alignment requirements.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc 4.7 produces a spurious warning about an array subscript being out
of bounds. Use a pointer dereference instead of an array lookup to
inhibit this spurious warning.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On i350 the datasheet contradicts itself in stating that the default
value of RXDCTL.ENABLE for queue zero is both set (according to the
"Receive Initialization" section) and unset (according to the "Receive
Descriptor Control - RXDCTL" section). Empirical evidence suggests
that the default value is unset.
Explicitly enable both transmit and receive queues to avoid any
ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Refill receive ring only after enabling receiver
On 82576 (and probably others), the datasheet states that "the tail
register of the queue (RDT[n]) should not be bumped until the queue is
enabled". There is some confusion over exactly what constitutes
"enabled": the initialisation blurb says that we should "poll the
RXDCTL register until the ENABLE bit is set", while the description
for the RXDCTL register says that the ENABLE bit is set by default
(for queue zero). Empirical evidence suggests that the ENABLE bit
reads as set immediately after writing to RCTL.EN, and so polling is
not necessary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hw pointer in PCI driver data as expected by sky2_remove().
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Support RTL8139 cards within generic Realtek driver
RTL8139C+ cards use essentially the same datapath as RTL8169, which is
zerocopy and 64-bit capable. Older RTL8139 cards use a single receive
ring buffer rather than a descriptor ring, but still share substantial
amounts of functionality with RTL8169.
Include support for RTL8139 cards within the generic Realtek driver,
since there is no way to differentiate between RTL8139 and RTL8139C+
cards based on the PCI IDs alone.
Many thanks to all the people who worked on the rtl8139 driver over
the years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The link state is currently set at probe time, and updated only when
the device is polled. This results in the user seeing a misleading
stale "Link: down" message, if autonegotiation did not complete within
the short timespan of the probe routine.
Fix by updating the link state when the device is opened, so that the
message that ends up being displayed to the user reflects the real
link state at device open time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE provides no support for manually configuring the link speed.
Provide a generic routine which should be able to reset any MII/GMII
PHY and enable autonegotiation.
Prototyped-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown