[interface] Unplug interface before calling intf_close() in intf_shutdown()
The call to intf_close() may result in the original interface being
reopened. For example: when reading the capacity of a 2TB+ disk via
iSCSI, the SCSI layer will respond to the intf_close() from the READ
CAPACITY (10) command by immediately issuing a READ CAPACITY (16)
command. The iSCSI layer happens to reuse the same interface for the
new command (since it allows only a single concurrent command).
Currently, intf_shutdown() unplugs the interface after the call to
intf_close() returns. In the above scenario, this results in
unplugging the just-reopened interface.
Fix by transferring the interface destination (and its reference) to a
temporary interface, and so effectively performing the unplug before
making the call to intf_close().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Fix building elf2efi.c when -fpic is enabled by default
The x86_64 EDK2 headers include a #pragma to mark all subsequent
symbol declarations and references as hidden if position-independent
code is being generated. Since libgen.h is currently included only
after the EDK2 headers, this results in __xpg_basename() being
erroneously marked as having hidden visibility (if the compiler
defaults to building position-independent code); this eventually
results in a failure to link the elf2efi binary.
Fix by including libgen.h prior to including the EDK2 headers.
Originally-fixed-by: Doug Goldstein <cardoe@cardoe.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In some high-end Azure instances (e.g. NC6) we may receive an
unsolicited VMBUS_OFFER_CHANNEL message for a PCIe pass-through device
some time after completing the bus enumeration. This currently causes
apparently random failures due to unexpected VMBus message types.
Fix by ignoring any unsolicited VMBus messages.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[cloud] Show CPU vendor and model in example cloud boot scripts
Some problems arise only when running on a specific CPU type (e.g.
non-functional timer interrupts as observed in Azure AMD instances).
Include the CPU vendor and model within the sample cloud boot scripts,
to assist in debugging such problems.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a settings applicator to modify netdev->max_pkt_len in
response to changes to the "mtu" setting (DHCP option 26).
Note that as with MAC address changes, drivers are permitted to
completely ignore any changes in the MTU value. The net result will
be that iPXE effectively uses the smaller of either the hardware
default MTU or the software configured MTU.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[cloud] Add ability to retrieve Google Compute Engine metadata
For some unspecified "security" reason, the Google Compute Engine
metadata server will refuse any requests that do not include the
non-standard HTTP header "Metadata-Flavor: Google".
Attempt to autodetect such requests (by comparing the hostname against
"metadata.google.internal"), and add the "Metadata-Flavor: Google"
header if applicable.
Enable this feature in the CONFIG=cloud build, and include a sample
embedded script allowing iPXE to boot from a script configured as
metadata via e.g.
# Create shared boot image
make bin/ipxe.usb CONFIG=cloud EMBED=config/cloud/gce.ipxe
# Configure per-instance boot script
gcloud compute instances add-metadata <instance> \
--metadata-from-file ipxeboot=boot.ipxe
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[virtio] Use separate RX and TX empty header buffers
Some host implementations (notably Google Compute Platform) are known
to unconditionally write back VIRTIO_NET_HDR_F_DATA_VALID to
header->flags for received packets, regardless of the features
negotiated by the driver. This breaks the transmit datapath by
effectively setting an illegal flag for all subsequent transmitted
packets.
Work around this problem by using separate empty header buffers for
the receive and transmit queues.
Debugged-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This code largely inspired by tap.c. Allows for testing iPXE on real
NICs from within Linux. For example:
make bin-x86_64-linux/af_packet.linux
valgrind ./bin-x86_64-linux/af_packet.linux --net af_packet,if=eth3
Tested as x86_64 and i386 binary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Virtio 0.9 implementation was limited to the maximum virtqueue size of
MAX_QUEUE_NUM and the virtio-net driver would fail to initialize on hosts
exceeding this limit.
This commit lifts the restriction by allocating the queue memory based on
the actual queue size instead of using a fixed maximum. Note that virtio
1.0 still uses the MAX_QUEUE_NUM constant to cap the size (unfortunately
this functionality is not available in virtio 0.9).
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This commit introduces virtnet_free_virtqueues called on all virtqueue
error and shutdown paths. vpm_find_vqs no longer cleans up after itself
and instead expects virtnet_free_virtqueues to be always called to undo
its effect.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
vpm_find_vqs incorrectly accepted the host provided queue size with no
regard to iPXE's internal limitations. Virtio 1.0 makes it possible for
the driver to override the queue size to reduce memory requirements and
iPXE is a great use case for this feature.
Also removing the extra vq->vring.num assignment which is already
handled in vring_init.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv4] Accept unicast packets for the local network broadcast address
The ISC Kea DHCP server transmits its DHCPOFFER as a unicast packet
with a broadcast IPv4 destination address (255.255.255.255). This
combination is currently rejected by iPXE.
Fix by explicitly accepting the local network broadcast address
(255.255.255.255) as a valid unicast destination address.
Reported-by: Roy Ledochowski <roy.ledochowski@hpe.com>
Tested-by: Roy Ledochowski <roy.ledochowski@hpe.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[golan] Update Connect-IB, ConnectX-4 and ConnectX-4 Lx (Infiniband) support
Updates:
- Nodnic: Support for arm cq doorbell via the UAR BAR
- Ensure hardware is quiescent when no interface is open - WinPE WA
- Support for clear interrupt via BAR
- Nodnic: Support for send TX doorbells via the UAR BAR
- Added ConnectX-5EX device
- Added ConnectX-5 device
Signed-off-by: Raed Salem <raeds@mellanox.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Work around temporal anomaly encountered during ExitBootServices()
EFI provides no clean way for device drivers to shut down in
preparation for handover to a booted operating system. The platform
firmware simply doesn't bother to call the drivers' Stop() methods.
Instead, drivers must register an EVT_SIGNAL_EXIT_BOOT_SERVICES event
to be signalled when ExitBootServices() is called, and clean up
without any reference to the EFI driver model.
Unfortunately, all timers silently stop working when ExitBootServices()
is called. Even more unfortunately, and for no discernible reason,
this happens before any EVT_SIGNAL_EXIT_BOOT_SERVICES events are
signalled. The net effect of this entertaining design choice is that
any timeout loops on the shutdown path (e.g. for gracefully closing
outstanding TCP connections) may wait indefinitely.
There is no way to report failure from currticks(), since the API
lazily assumes that the host system continues to travel through time
in the usual direction. Work around EFI's violation of this
assumption by falling back to a simple free-running monotonic counter.
Debugged-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[undi] Try matching UNDI ROMs in BIOS enumeration order
When searching for an UNDI ROM to match against a PCI device, search
in order of increasing ROM address (within the 128kB BIOS option ROM
area). This is likely (though not guaranteed) to match the order of
the original enumeration performed by the BIOS, which is in turn
likely to match the order of enumeration on the PCI bus.
Since we load at most one UNDI ROM, the net result is that we increase
our chances of loading the ROM corresponding to the selected PCI
device (rather than loading a ROM corresponding to a higher-numbered
PCI device with the same vendor and device IDs.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "progress" macro can be used only from within the .prefix section.
At the point of calling relocate(), we are running in .text16 and so
the near call to print_message() will end up calling a random function
somewhere in .text16.
Interestingly, this problem has remained unnoticed for some time. It
is rare to build with DEBUG=libprefix. In the few cases that it has
been used during development, the randomly selected function in
.text16 seems to have been a harmless no-op with no visible
side-effects (beyond the unnoticed failure to print the "relocate"
progress message).
Fix by removing the futile attempt to print a progress message before
calling relocate().
Reported-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[undi] Clean up driver and device name information
Fix the <NULL> driver name reported by "ifstat" when using the undipci
driver (due to the unnecessary extra device node inserted as a child
of the PCI device).
Remove the "UNDI-" prefix from device names since the driver name is
also now visible via "ifstat", and tidy up the device name to match
the format used by standard PCI devices.
The output from "ifstat" now resembles:
iPXE> ifstat
net0: 52:54:00:12:34:56 using undipci on 0000:00:03.0
iPXE> ifstat
net0: 52:54:00:12:34:56 using undionly on 0000:00:03.0
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Avoid using PMM-allocated memory in UNDI loader entry point
The UNDI loader entry point is very likely to be called after POST,
when there is a high chance that the PMM-allocated image source area
and decompression area have been reused by something else.
In particular, using an iPXE .iso to test a separate iPXE ROM's UNDI
loader entry point in a qemu VM is likely to crash. SeaBIOS allocates
PMM blocks from close to the top of memory and so these blocks have a
high chance of colliding with the runtime addresses subsequently
chosen by the non-ROM iPXE by scanning the INT 15,e820 memory map.
The standard romprefix.S has no choice about relying on the
PMM-allocated image source area, since it has no other way to retrieve
its compressed payload.
In mromprefix.S, the image source area functions only as an optional
buffer used to avoid repeated reads from the (potentially slow)
expansion ROM BAR by the decompression code. We can therefore always
set %esi=0 when calling install_prealloc from the UNDI loader entry
point, and simply fall back to reading directly from the expansion ROM
BAR.
We can always set %edi=0 when calling install_prealloc from the UNDI
loader entry point. This will behave as though the decompression area
PMM allocation failed, and will therefore use INT 15,88 to find a
temporary decompression area somewhere close to 64MB. This is by no
means guaranteed to be safe from collisions, but it's probably safer
on balance than the PMM-allocated address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[undi] Allocate base memory before calling UNDI loader entry point
Allocate base memory (by decreasing the free base memory counter)
before calling the UNDI loader entry point, to minimise surprises for
the UNDI loader code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[iscsi] Avoid potential infinite loops during shutdown
The command and data interfaces may be connected to the same object.
Nullify the data interface before shutting down the control interface
to avoid potential infinite loops.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Conditionalize the workaround for the Tivoli VMM's SSE garbling
Commit 71560d1 ("[librm] Preserve FPU, MMX and SSE state across calls
to virt_call()") added FXSAVE and FXRSTOR instructions to iPXE. In
KVM virtual machines, these instructions execute fine as long as the
host CPU supports the "unrestricted_guest" feature (that is, it can
virtualize big real mode natively). On older host CPUs however, KVM
has to emulate big real mode, and it currently doesn't implement
FXSAVE emulation.
Upstream QEMU rebuilt iPXE at commit 0418631 ("[thunderx] Fix
compilation with older versions of gcc") which is a descendant of
commit 71560d1 (see above).
This was done in QEMU commit ffdc5a2 ("ipxe: update submodule from
4e03af8ec to 041863191"). The resultant binaries were bundled with
the QEMU v2.7.0 release; see QEMU commit c52125a ("ipxe: update
prebuilt binaries").
This distributed the iPXE workaround for the Tivoli VMM bug to a
number of KVM users with old host CPUs, causing KVM emulation failures
(guest crashes) for them while netbooting.
Make the FXSAVE and FXRSTOR instructions conditional on a new feature
test macro called TIVOLI_VMM_WORKAROUND. Define the macro by default.
There is prior art for an assembly file including config/general.h:
see arch/x86/prefix/romprefix.S. Also, TIVOLI_VMM_WORKAROUND seems to
be a good fit for the "Obscure configuration options" section in
config/general.h.
Cc: Bandan Das <bsd@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Greg <rollenwiese@yahoo.com>
Cc: Michael Brown <mcb30@ipxe.org>
Cc: Michael Prokop <launchpad@michael-prokop.at>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Pickford <arch@netremedies.ca>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Ref: https://bugs.archlinux.org/task/50778
Ref: https://bugs.launchpad.net/qemu/+bug/1623276
Ref: https://bugzilla.proxmox.com/show_bug.cgi?id=1182
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1356762
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The initrd_addr_max field represents the highest byte address that may
be used to hold initrd images, and is therefore almost certainly not
aligned to a page boundary: a typical value might be 0x7fffffff.
Fix the address calculations to ensure that the initrd images are
always aligned to a page boundary.
Reported-by: Sitsofe Wheeler <sitsofe@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
AppleNetBoot.h is not taken from the EDK2 codebase and so cannot be
imported using include/ipxe/efi/import.pl. Mark as a native iPXE
header (by changing the include guard) to avoid breaking the import
process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Allow certificates to be marked as having been added explicitly
Allow certificates to be marked as having been added explicitly at run
time. Such certificates will not be discarded via the certificate
store cache discarder.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Enable IMAGE_PNG (but not IMAGE_PNM) by default, and drag in the
relevant objects only when image_pixbuf() is present in the binary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Enable both DER and PEM formats by default
Enable both IMAGE_DER and IMAGE_PEM by default, and drag in the
relevant objects only when image_asn1() is present in the binary.
This allows "imgverify" to transparently use either DER or PEM
signature files.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As of commit b1caa48 ("[crypto] Support SHA-{224,384,512} in X.509
certificates"), the list of supported cryptographic algorithms is
controlled by config/crypto.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add PEM-encoded ASN.1 as an image format. We accept as PEM any image
containing a line starting with a "-----BEGIN" boundary marker.
We allow for PEM files containing multiple ASN.1 objects, such as a
certificate chain produced by concatenating individual certificate
files.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add DER-encoded ASN.1 as an image format. There is no fixed signature
for DER files. We treat an image as DER if it comprises a single
valid SEQUENCE object covering the entire length of the image.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown