Abstract out the ability to reboot the system to a separate reboot()
function (with platform-specific implementations), add an EFI
implementation, and make the existing "reboot" command available under
EFI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcp] Use PXE byte ordering for UUID in DHCP option 97
The PXE spec does not specify a byte ordering for UUIDs, but RFC4578
suggests that it follows the EFI spec, in which the first three fields
are little-endian.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smbios] Mangle UUIDs for SMBIOS version 2.6 and newer
iPXE treats UUIDs as being in network byte order (big-endian). The
SMBIOS specification version 2.6 states that UUIDs are stored with
little-endian values in the first three fields; earlier versions did
not specify an endianness. This results in some inconsistency between
the BIOS, vendor PXE, iPXE, and operating system interpretations of
the SMBIOS UUID.
dmidecode assumes that the byte order is little-endian if and only if
the SMBIOS version is 2.6 or higher. Choose to match this behaviour.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Reported-by: Alexandru Bordei <alexandru.bordei@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[lkrnprefix] Allow relocation when no initrd is present
Commit 2629b7e ("[pcbios] Inhibit all calls to INT 15,e820 and INT
15,e801 during POST") introduced a regression into .lkrn images when
used with no corresponding initrd.
Specifically, the semantics of the "maximum address for relocation"
value passed to install_prealloc() in %ebp changed so that zero became
a special value meaning "inhibit use of INT 15,e820 and INT 15,e801".
The %ebp value meaing "no upper limit on relocation" was changed from
zero to 0xffffffff, and all prefixes providing fixed values for %ebp
were updated to match the new semantics.
The .lkrn prefix provides the initrd base address as the maximum
address for relocation. When no initrd is present, this address will
be zero, and so will unintentionally trigger the "inhibit INT 15,e820
and INT 15,e801" behaviour.
Fix by explicitly setting %ebp to 0xffffffff if no initrd is present
before calling install_prealloc().
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Tested-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Newer versions of bfd.h require definitions for the PACKAGE and
PACKAGE_VERSION macros used by autotools. Work around this by
manually defining these macros before including bfd.h.
Originally-fixed-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Tested-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Add our own EFI_LOAD_FILE_PROTOCOL implementation
When iPXE is used as a UEFI driver, the UEFI PXE base code currently
provides the TCP/IP stack, network protocols, and user interface.
This represents a substantial downgrade from the standard BIOS iPXE
user experience.
Fix by installing our own EFI_LOAD_FILE_PROTOCOL implementation which
initiates the standard iPXE boot procedure. This upgrades the UEFI
iPXE user experience to match the standard BIOS iPXE user experience.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Expose downloaded images via EFI_SIMPLE_FILE_SYSTEM_PROTOCOL
Expose iPXE's images as a UEFI file system, allowing the booted image
to access all images downloaded by iPXE.
This functionality is complementary to the custom iPXE download
protocol. The iPXE download protocol allows a booted image to utilise
iPXE to download arbitrary URIs, but requires the booted image to
specifically support the custom iPXE download protocol. The new
functionality limits the booted image to accessing only files that
were already downloaded by iPXE (e.g. as part of a script), but can
work with any generic UEFI image (e.g. the UEFI shell). Both
protocols are provided simultaneously, and are attached to the SNP
device handle.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Display only one "Ctrl-B" prompt per PCI device during POST
If a multifunction PCI device exposes an iPXE ROM via each function,
then each function will display a "Press Ctrl-B to configure iPXE"
prompt, and delay for two seconds. Since a single instance of iPXE
can drive all functions on the multifunction device, this simply adds
unnecessary delay to the boot process.
Fix by inhibiting the "Press Ctrl-B" prompt for all except the first
function on a PCI device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pcbios] Inhibit all calls to INT 15,e820 and INT 15,e801 during POST
Many BIOSes do not construct the full system memory map until after
calling the option ROM initialisation entry points. For several
years, we have added sanity checks and workarounds to accommodate
charming quirks such as BIOSes which report the entire 32-bit address
space (including all memory-mapped PCI BARs) as being usable RAM.
The IBM x3650 takes quirky behaviour to a new extreme. Calling either
INT 15,e820 or INT 15,e801 during POST doesn't just get you invalid
data. We could cope with invalid data. Instead, these nominally
read-only API calls manage to trash some internal BIOS state, with the
result that the system memory map is _never_ constructed. This tends
to confuse subsequent bootloaders and operating systems.
[ GRUB 0.97 fails in a particularly amusing way. Someone thought it
would be a good idea for memcpy() to check that the destination memory
region is a valid part of the system memory map; if not, then memcpy()
will sulk, fail, and return NULL. This breaks pretty much every use
of memcpy() including, for example, those inserted implicitly by gcc
to copy non-const initialisers. Debugging is _fun_ when a simple call
to printf() manages to create an infinite recursion, exhaust the
available stack space, and shut down the CPU. ]
Fix by completely inhibiting calls to INT 15,e820 and INT 15,e801
during POST.
We do now allow relocation during POST up to the maximum address
returned by INT 15,88 (which seems so far to always be safe). This
allows us to continue to have a reasonable size of external heap, even
if the PMM allocation is close to the 1MB mark.
The downside of allowing relocation during POST is that we may
overwrite PMM-allocated memory in use by other option ROMs. However,
the downside of inhibiting relocation, when combined with also
inhibiting calls to INT 15,e820 and INT 15,e801, would be that we
might have no external heap available: this would make booting an OS
impossible and could prevent some devices from even completing
initialisation.
On balance, the lesser evil is probably to allow relocation during
POST (up to the limit provided by INT 15,88). Entering iPXE during
POST is a rare operation; on the even rarer systems where doing so
happens to overwrite a PMM-allocated region, then there exists a
fairly simple workaround: if the user enters iPXE during POST and
wishes to exit iPXE, then the user must reboot. This is an acceptable
cost, given the rarity of the situation and the simplicity of the
workaround.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[prefix] Use %cs as implicit parameter to uninstall()
romprefix.S currently calls uninstall() with an invalid value in %ax.
Consequently, base memory is not freed after a ROM boot attempt (or
after entering iPXE during POST).
The uninstall() function is physically present in .text16, and so can
use %cs to determine the .text16 segment address. The .data16 segment
address is not required, since uninstall() is called only by code
paths which set up .data16 to immediately follow .text16.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add "make vmware" build target, to build all of the ROMs used with
VMware.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tftp] Allow TFTP block size to be controlled via the PXE TFTP API
The PXE TFTP API allows the caller to request a particular TFTP block
size. Since mid-2008, iPXE has appended a "?blksize=xxx" parameter to
the TFTP URI constructed internally; nothing has ever parsed this
parameter. Nobody seems to have cared that this parameter has been
ignored for almost five years.
Fix by using xfer_window(), which provides a fairly natural way to
convey the block size information from the PXE TFTP API to the TFTP
protocol layer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[menu] Prevent separators with shortcut keys from being selected
Nothing currently prevents a menu separator from being assigned a
shortcut key, and then from being selected using that shortcut key.
This produces an inconsistency in the user interface, since separators
cannot be selected by other means of menu navigation (arrow keys, page
up/down, etc).
It would be trivial to prevent separators from being assigned shortcut
keys, but this would eliminate one potentially useful use case: having
a large menu and using shortcut keys to jump to a section within the
menu.
Fix by treating a shortcut key on a separator as equivalent to "select
the separator, then press the down arrow key". This has the effect of
moving to the first non-separator menu item following the specified
separator, which is probably the most intuitive behaviour. (The
existing logic for moving the selection already handles the various
nasty corner cases such as a menu ending with one or more separators.)
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[menu] Prevent character code zero from acting as a shortcut key
Unrecognised keys may be returned by getkey() as character code zero,
which currently matches against the first menu item with no shortcut
key defined.
Prevent this unintended behaviour by explicitly checking that the menu
item has a defined shortcut key.
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[zbin] Fix size used for memset in alloc_output_file
The output->buf field is a pointer, not an array, so sizeof() is not
applicable. We must use the allocated string length instead.
Identified by gcc:
util/zbin.c: In function ‘alloc_output_file’:
util/zbin.c:146:37: warning: argument to ‘sizeof’ in ‘memset’ call
is the same expression as the destination; did you mean to
dereference it? [-Wsizeof-pointer-memaccess]
memset ( output->buf, 0xff, sizeof ( output->buf ) );
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[undi] Work around specific devices with known broken interrupt behaviour
Some PXE stacks are known to claim that IRQs are supported, but then
never generate interrupts. No satisfactory solution has been found to
this problem; the workaround is to add the PCI vendor and device IDs
to a list of devices which will be treated as simply not supporting
interrupts.
This is something of a hack, since it will generate false positives
for identical devices with a working PXE stack (e.g. those that have
been reflashed with iPXE), but it's an improvement on the current
situation.
Reported-by: Richard Moore <rich@richud.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Separate VLAN support from presence of VLAN-supporting drivers
Some NICs (e.g. Hermon) provide hardware support for stripping the
VLAN tag, but do not provide any way for this support to be disabled.
Drivers for this hardware must therefore call vlan_find() to identify
a suitable receiving network device.
Provide a weak version of vlan_find() which will always return NULL if
VLAN support has not been enabled (either directly, or by enabling
a feature such as FCoE which requires VLAN support). This allows the
VLAN code to be omitted from builds where the user has not requested
support for VLANs.
Inspired-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iBFT NIC section has a VLAN field which must be filled in so that
iSCSI booting works over VLANs.
Unfortunately it is unclear from the IBM specification linked in
ibft.c whether the VLAN field is just the 802.1Q VLAN Identifier or
the full 802.1Q TCI. For now just fill in the VID, the Priority Code
Point and Drop Eligible Indicator could be set in the future if it
turns out they should be present too.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Add vlan_tag() to get the VLAN tag of a network device
The iBFT has a VLAN field that should be filled in. Add the
vlan_tag() function to extract the VLAN tag of a network device.
Since VLAN support is optional, define a weak function that returns 0
when iPXE is built without VLAN support.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Ensure EFI binaries comply with Authenticode requirements
Authenticode requires that the size of the raw file must equal the
size of the OptionalHeader.SizeOfHeaders plus the sum of all sections'
SizeOfRawData.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tls] Concatenate received non-data records before processing
Allow non-data records to be split across multiple received I/O
buffers, to accommodate large certificate chains.
Reported-by: Nicola Volpini <Nicola.Volpini@kambi.com>
Tested-by: Nicola Volpini <Nicola.Volpini@kambi.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Delegate to child device's EFI_COMPONENT_NAME2_PROTOCOL, if present
EFI's device naming model requires drivers to provide names for child
devices. Allow the driver's GetControllerName() method to delegate to
an instance of EFI_COMPONENT_NAME2_PROTOCOL installed on the child
device itself (if present); this allows the SNP device to expose its
own device name via the PCI driver's GetControllerName() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At present, loading a bzImage via iPXE requires enough RAM to hold two
copies of each initrd file. Remove this constraint by rearranging the
initrds in place.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No code from the original source remains within this file; relicense
under GPL2+ with a new copyright notice.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown