gcc 4.7 produces a spurious warning about an array subscript being out
of bounds. Use a pointer dereference instead of an array lookup to
inhibit this spurious warning.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On i350 the datasheet contradicts itself in stating that the default
value of RXDCTL.ENABLE for queue zero is both set (according to the
"Receive Initialization" section) and unset (according to the "Receive
Descriptor Control - RXDCTL" section). Empirical evidence suggests
that the default value is unset.
Explicitly enable both transmit and receive queues to avoid any
ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Refill receive ring only after enabling receiver
On 82576 (and probably others), the datasheet states that "the tail
register of the queue (RDT[n]) should not be bumped until the queue is
enabled". There is some confusion over exactly what constitutes
"enabled": the initialisation blurb says that we should "poll the
RXDCTL register until the ENABLE bit is set", while the description
for the RXDCTL register says that the ENABLE bit is set by default
(for queue zero). Empirical evidence suggests that the ENABLE bit
reads as set immediately after writing to RCTL.EN, and so polling is
not necessary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hw pointer in PCI driver data as expected by sky2_remove().
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Support RTL8139 cards within generic Realtek driver
RTL8139C+ cards use essentially the same datapath as RTL8169, which is
zerocopy and 64-bit capable. Older RTL8139 cards use a single receive
ring buffer rather than a descriptor ring, but still share substantial
amounts of functionality with RTL8169.
Include support for RTL8139 cards within the generic Realtek driver,
since there is no way to differentiate between RTL8139 and RTL8139C+
cards based on the PCI IDs alone.
Many thanks to all the people who worked on the rtl8139 driver over
the years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The link state is currently set at probe time, and updated only when
the device is polled. This results in the user seeing a misleading
stale "Link: down" message, if autonegotiation did not complete within
the short timespan of the probe routine.
Fix by updating the link state when the device is opened, so that the
message that ends up being displayed to the user reflects the real
link state at device open time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE provides no support for manually configuring the link speed.
Provide a generic routine which should be able to reset any MII/GMII
PHY and enable autonegotiation.
Prototyped-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for 82579-based chips such as those found on Sandy Bridge
motherboards. Based on d3738bb820 in
Linux.
Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Practically speaking, it seems the convention is to only have one
packet pending and not rely upon any mechanism to associate returned
txbuf with txqueue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This function never did much in this driver anyway, and after commit
b5ed30b2 ("[tg3] Fix compilation on newer gcc versions") it became
apparent that its remaining functionality could be easily moved to
tg3_test_dma().
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the old Etherboot tg3 driver with a more up-to-date driver
using the iPXE API.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The RS bit is used to instruct the NIC to update the TX descriptor
status byte. The RPS bit is used to instruct the NIC to defer this
update until after the packet has been transmitted on the wire (rather
than merely read into the transmit FIFO).
The driver currently sets RPS but not RS. Some e1000 models seem to
interpret this as implying that the status byte should be updated;
some don't. On the ones that don't, we never see any TX completions
and so rapidly run out of TX buffers.
Fix by setting the RS bit in the TX descriptor. (We don't care about
when the packet reaches the wire, so don't bother setting the RPS
bit.)
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hermon] Ensure hardware is quiescent when no interfaces are open
WinPE has been observed to call PXENV_UNDI_SHUTDOWN but not
PXENV_STOP_UNDI. This means that Hermon hardware is left partially
active (firmware running and one event queue mapped) when WinPE starts
up, which can cause a Blue Screen of Death.
Fix by ensuring that the hardware is left quiescent (with the firmware
stopped) when no interfaces are open.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipoib] Report packets as broadcast when ambiguous
Avoid spurious matches for peer key 0 against empty peer cache
entries, and set the LL_MULTICAST flag in addition to LL_BROADCAST.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[rtl8139] Perform only 8-bit ioport access on the ChipCmd register
The ChipCmd register is only an 8-bit register. The 16-bit access
used by iPXE was causing an issue when used with qemu emulated rtl8139
device which was improperly aligning IOs.
Signed-off-by: Julian Pidancet <julian.pidancet@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[arbel] Add (not-yet-functional) support for RC queue pairs
Arbel seems to crash the system as soon as the first send WQE
completes on an RC queue pair. (NOPs complete successfully, so this
is a problem specific to the work queue rather than the completion
queue.) The cause of this problem has remained unknown for over a
year.
Check in the non-functioning code to avoid bit-rot, and in the hope
that someone will find the fix.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Allow link layer to report broadcast/multicast packets via pull()
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[process] Pass containing object pointer to process step() methods
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Alexey