[e1000] Remove unused variable when ICR register is simply cleared
On reset and close, the ICR register is read to clear any pending
interrupts, but the value is simply ignored. Avoid assigning the
value to a variable, to inhibit a warning from gcc 4.6.
Also fix a potential race condition in reset routines which clear
interrupts before disabling them.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[igbvf] Remove some unused Linux-specific portions of igbvf.h
These unused portions trigger a compiler warning under gcc 4.6, due to
the ambiguity over the "page" field in struct igbvf_buffer.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a virtual environment such as qemu, we can legitimately receive
packets less than 64 bytes in length, such as ARP replies. These are
currently discarded, causing most IPv4 communication to fail.
Fix by ignoring the RFDShort bit when receiving packets.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When chainloading rtl8139.pxe from an old Etherboot rtl8139.zrom, iPXE
can end up misreading the first word of the MAC address from the
EEPROM as being all zeroes. This is presumably because Etherboot has
left the serial EEPROM in an unexpected state.
Fix by using the chip select line to reset the SPI device before we
start accessing it.
Reported-by: Mandar U Jog <mandarjog@gmail.com>
Tested-by: Mandar U Jog <mandarjog@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The default initiator IQN is "iqn.2000-09.org.etherboot:UNKNOWN".
This is problematic for two reasons:
a) the etherboot.org domain (and hence the associated IQN namespace)
is not under the control of the iPXE project, and
b) some targets (correctly) refuse to allow concurrent connections
from different initiators using the same initiator IQN.
Solve both problems by changing the default initiator IQN to be
iqn.2010-04.org.ipxe:<hostname> if a hostname is set, or
iqn.2010-04.org.ipxe:<uuid> if no hostname is set.
Explicit initiator IQNs set via DHCP option 203 are not affected by
this change.
Unfortunately, this change is likely to break some existing
configurations, where ACL rules have been put in place referring to
the old default initiator IQN. Users may need to update ACLs, or
force the use of the old IQN using an iPXE script line such as
set initiator-iqn iqn.2000-09.org.etherboot:UNKNOWN
or a dhcpd.conf option such as
option iscsi-initiator-iqn "iqn.2000-09.org.etherboot:UNKNOWN"
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some operating environments require (or at least prefer) that we do
not perform our own PCI bus scan, but deal only with specified
devices. Modularise the PCI core to allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pci] Use single "busdevfn" field in struct pci_device
Merge the "bus" and "devfn" fields into a single "busdevfn" field, to
match the format used by the majority of external code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On 64-bit builds, MLX_DECLARE_STRUCT() produces a structure that is
always a multiple of 64 bits long, causing the HCR structure to be
over-length by one dword. This in turn causes hermon_cmd() to write
beyond the end of the HCR, which causes commands to fail.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid memory leak of untreated events by having circular event queue
operation.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove duplicate hardware resets, remove network interface logic
reset.
This also fixes a bug where some 3c905C variants would return bogus
EEPROM values because of a too short delay after the network reset.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Reported-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DBG is reserved for errors and important warnings only.
DBG2 for additional information, e.g. "received packet".
DBGP is used to print the name of every function as it is called.
Signed-off-by: Thomas Miletich<thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the concept of shutdown exit flags, and replace it with a
counter used to keep track of exposed interfaces that require devices
to remain active.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[vxge] Add support for new function mode "multi-function 8 Direct IO"
Support a new function mode "multi-function 8 Direct IO" which is used
in ESX Direct I/O configuration.
Update driver version to 3.5.0.1
Signed-off-by: Masroor Vettuparambil <masroor.vettuparambil@exar.com>
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@exar.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pci] Allow pci_vpd_init() return status to be ignored
Most xxx_init() functions are void functions with no failure cases.
Allow pci_vpd_init() to be used in the same way. (Subsequent calls to
pci_vpd_read() etc. will fail if pci_vpd_init() fails.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[nvo] Remove the non-volatile options fragment list
Since its implementation several years ago, no driver has used a
fragment list containing more than a single fragment. Simplify the
NVO core and the drivers that use it by removing the whole concept of
the fragment list, and using a simple (address,length) pair instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[legal] Add FILE_LICENCE macro to some GPL-v2-or-later files
Changes were made to files where the licence text within the files
themselves confirms that the files are GPL version 2 or later.
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Apply settings block name in register_settings()
Pass the settings block name as a parameter to register_settings(),
rather than defining it with settings_init() (and then possibly
changing it by directly manipulating settings->name).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[scsi] Wait for a successful TEST UNIT READY command
Some SCSI targets (observed with an EMC CLARiiON Fibre Channel target)
will not respond to commands correctly until a TEST UNIT READY has
been issued. In particular, a READ CAPACITY (10) command will return
with a success status, but no capacity data.
Fix by issuing a TEST UNIT READY command automatically, and delaying
further SCSI commands until the TEST UNIT READY has succeeded.
Reported-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
FCoE requires us to be able to receive unicast packets for multiple
addresses. Support this by operating in promiscuous mode.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown