Select the IPv6 source address and corresponding router (if any) using
a very simplified version of the algorithm from RFC6724:
- Ignore any source address that has a smaller scope than the
destination address. For example, do not use a link-local source
address when sending to a global destination address.
- If we have a source address which is on the same link as the
destination address, then use that source address.
- If we are left with multiple possible source addresses, then choose
the address with the smallest scope. For example, if we are sending
to a site-local destination address and we have both a global source
address and a site-local source address, then use the site-local
source address.
- If we are still left with multiple possible source addresses, then
choose the address with the longest matching prefix.
For the purposes of this algorithm, we treat RFC4193 Unique Local
Addresses as having organisation-local scope. Since we use only
link-local scope for our multicast transmissions, this approximation
should remain valid in all practical situations.
Originally-implemented-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv6] Create routing table based on IPv6 settings
Use the IPv6 settings to construct the routing table, in a matter
analogous to the construction of the IPv4 routing table.
This allows for manual assignment of IPv6 addresses via e.g.
set net0/ip6 2001:ba8:0:1d4::6950:5845
set net0/len6 64
set net0/gateway6 fe80::226:bff:fedd:d3c0
The prefix length ("len6") may be omitted, in which case a default
prefix length of 64 will be assumed.
Multiple IPv6 addresses may be assigned manually by implicitly
creating child settings blocks. For example:
set net0/ip6 2001:ba8:0:1d4::6950:5845
set net0.ula/ip6 fda4:2496:e992::6950:5845
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv6] Match user expectations for IPv6 settings priorities
A reasonable user expectation is that ${net0/ip6} should show the
"highest-priority" of the IPv6 addresses, even when multiple IPv6
addresses are active. The expected order of priority is likely to be
manually-assigned addresses first, then stateful DHCPv6 addresses,
then SLAAC addresses, and lastly link-local addresses.
Using ${priority} to enforce an ordering is undesirable since that
would affect the priority assigned to each of the net<N> blocks as a
whole, so use the sibling ordering capability instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Allow settings blocks to specify a sibling ordering
Allow settings blocks to provide an explicit default ordering between
siblings, with lower precedence than the existing ${priority} setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Originally-implemented-by: Hannes Reinecke <hare@suse.de>
Originally-implemented-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose the IPv6 address (or prefix) as ${ip6}, the prefix length as
${len6}, and the router address as ${gateway6}.
Originally-implemented-by: Hannes Reinecke <hare@suse.de>
Originally-implemented-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The settings scope ipv6_scope refers specifically to IPv6 settings
that have a corresponding DHCPv6 option. Rename to dhcpv6_scope to
more accurately reflect this purpose.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Install the HII config access protocol on a child of the SNP handle
In edk2, there are several drivers that associate HII forms (and
corresponding config access protocol instances) with each individual
network device. (In this context, "network device" means the EFI
handle on which the SNP protocol is installed, and on which the device
path ending with the MAC() node is installed also.) Such edk2 drivers
are, for example: Ip4Dxe, HttpBootDxe, VlanConfigDxe.
In UEFI, any given handle can carry at most one instance of a specific
protocol (see e.g. the specification of the InstallProtocolInterface()
boot service). This implies that the class of drivers mentioned above
can't install their EFI_HII_CONFIG_ACCESS_PROTOCOL instances on the
SNP handle directly -- they would conflict with each other.
Accordingly, each of those edk2 drivers creates a "private" child
handle under the SNP handle, and installs its config access protocol
(and corresponding HII package list) on its child handle.
The device path for the child handle is traditionally derived by
appending a Hardware Vendor Device Path node after the MAC() node.
The VenHw() nodes in question consist of a GUID (by definition), and
no trailing data (by choice). The purpose of these VenHw() nodes is
only that all the child nodes can be uniquely identified by device
path.
At the moment iPXE does not follow this pattern. It doesn't run into
a conflict when it installs its EFI_HII_CONFIG_ACCESS_PROTOCOL
directly on the SNP handle, but that's only because iPXE is the sole
driver not following the pattern. This behavior seems risky (one
might call it a "latent bug"); better align iPXE with the edk2 custom.
Cc: Michael Brown <mcb30@ipxe.org>
Cc: Gary Lin <glin@suse.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Ref: http://thread.gmane.org/gmane.comp.bios.edk2.devel/13494/focus=13532
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ladi Prosek <lprosek@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[profile] Allow profiling to be globally enabled or disabled
As with assertions, profiling is enabled for objects built with any
debug level (including an explicit debug level of zero).
Allow profiling to be globally enabled or disabled by adding PROFILE=1
or PROFILE=0 respectively to the build command line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[libc] Allow assertions to be globally enabled or disabled
Assertions are enabled for objects built with any debug level
(including an explicit debug level of zero). It is sometimes useful
to be able to enable assertions across all objects; this currently
requires manually hacking include/assert.h.
Allow assertions to be globally enabled by adding ASSERT=1 to the
build command line. For example:
make bin/8086100e.mrom ASSERT=1
Similarly, allow assertions to be globally disabled by adding ASSERT=0
to the build command line. If no ASSERT=... is specified on the
build command line, then only objects mentioned in DEBUG=... will have
assertions enabled (as is currently the case).
Note than globally enabling assertions imposes a relatively heavy
runtime penalty, primarily due to the various sanity checks performed
by list_add(), list_for_each_entry(), etc.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[debug] Allow debug messages to be initially disabled at runtime
Extend the DEBUG=... syntax to allow debug messages to be compiled in
but disabled by default. For example:
make bin/undionly.kpxe DEBUG=netdevice:3:1
would compile in the messages as for DEBUG=netdevice:3, but would set
the debug level mask so that only the DEBUG=netdevice:1 messages would
be displayed.
This allows for external code to selectively enable the additional
debug messages at runtime, without being overwhelmed by unwanted
initial noise. For example, a developer of a new protocol may want to
temporarily enable tracing of all packets received: this can be done
by building with DEBUG=netdevice:3:1 and using
// temporarily enable per-packet messages
DBG_ENABLE_OBJECT ( netdevice, DBGLVL_EXTRA );
...
// disable per-packet messages
DBG_DISABLE_OBJECT ( netdevice, DBGLVL_EXTRA );
Note that unlike the usual DBG_ENABLE() and DBG_DISABLE() macros,
DBG_ENABLE_OBJECT() and DBG_DISABLE_OBJECT() will not be removed via
dead code elimination if debugging is disabled in the specified
object. In particular, this means that using either of these macros
will always result in a symbol reference to the specified object.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[debug] Allow per-object runtime enabling/disabling of debug messages
The DBG_ENABLE() and DBG_DISABLE() macros currently affect the debug
level of all objects that were built with debugging enabled. This is
undesirable, since it is common to use different debug levels in each
object.
Make the debug level mask a per-object variable. DBG_ENABLE() and
DBG_DISABLE() now control only the debug level for the containing
object (which is consistent with the intended usage across the
existing codebase). DBG_ENABLE_OBJECT() and DBG_DISABLE_OBJECT() may
be used to control the debug level for a specified object. For
example:
// Enable DBG() messages from tcpip.c
DBG_ENABLE_OBJECT ( tcpip, DBGLVL_LOG );
Note that the existence of debug messages continues to be gated by the
DEBUG=... list specified on the build command line. If an object was
built without the relevant debug level, then DBG_ENABLE_OBJECT() will
have no effect on that object at runtime (other than to explicitly
drag in the object via a symbol reference).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcp] Automatically generate vendor class identifier string
The vendor class identifier strings in DHCP_ARCH_VENDOR_CLASS_ID are
out of sync with the (correct) client architecture values in
DHCP_ARCH_CLIENT_ARCHITECTURE.
Fix by removing all definitions of DHCP_ARCH_VENDOR_CLASS_ID, and
instead generating the vendor class identifier string automatically
based on DHCP_ARCH_CLIENT_ARCHITECTURE and DHCP_ARCH_CLIENT_NDI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcpv6] Include vendor class identifier option in DHCPv6 requests
RFC3315 defines DHCPv6 option 16 (vendor class identifier) but does
not define any direct relationship with the roughly equivalent DHCPv4
option 60.
The PXE specification predates IPv6, and the UEFI specification is
expectedly vague on the subject. Examination of the reference EDK2
codebase suggests that the DHCPv6 vendor class identifier will be
formatted in accordance with RFC3315, using a single vendor-class-data
item in which the opaque-data field is the string as would appear in
DHCPv4 option 60.
RFC3315 requires the vendor class identifier to specify an IANA
enterprise number, as a way of disambiguating the vendor-class-data
namespace. The EDK2 code uses the value 343, described as:
// TODO: IANA TBD: temporarily using Intel's
Since this "TODO" has been present since at least 2010, it is probably
safe to assume that it has now become a de facto standard.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcpv6] Include RFC5970 client architecture options in DHCPv6 requests
RFC5970 defines DHCPv6 options 61 (client system architecture type)
and 62 (client network interface identifier), with contents equivalent
to DHCPv4 options 93 and 94 respectively.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some of the regions may end up being unmapped, either because they are
optional or because the attempt to map them has failed. Region types
starting at 0 didn't make it easy to test for this condition.
This commit bumps all valid region types up by 1 with 0 having the
implicit 'unmapped' meaning.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[time] Allow system clock to be adjusted at runtime
Provide a mechanism to allow an arbitrary adjustment to be applied to
all subsequent calls to time().
Note that the underlying clock source (e.g. the RTC clock) will not be
changed; only the time as reported within iPXE will be affected.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcp] Send TCP keepalives on idle established connections
In some circumstances, intermediate devices may lose state in a way
that temporarily prevents the successful delivery of packets from a
TCP peer. For example, a firewall may drop a NAT forwarding table
entry.
Since iPXE spends most of its time downloading files (and hence purely
receiving data, sending only TCP ACKs), this can easily happen in a
situation in which there is no reason for iPXE's TCP stack to generate
any retransmissions. The temporary loss of connectivity can therefore
effectively become permanent.
Work around this problem by sending TCP keepalives after a period of
inactivity on an established connection.
TCP keepalives usually send a single garbage byte in sequence number
space that has already been ACKed by the peer. Since we do not need
to elicit a response from the peer, we instead send pure ACKs (with no
garbage data) in order to keep the transmit code path simple.
Originally-implemented-by: Ladi Prosek <lprosek@redhat.com>
Debugged-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pci] Support systems with multiple PCI root bridges
Extend the 16-bit PCI bus:dev.fn address to a 32-bit seg:bus:dev.fn
address, assuming a segment value of zero in contexts where multiple
segments are unsupported by the underlying data structures (e.g. in
the iBFT or BOFM tables).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Expose DHCP packets via the Apple NetBoot protocol
Mac OS X uses non-standard EFI protocols to obtain the DHCP packets
from the UEFI firmware.
Originally-implemented-by: Michael Kuron <m.kuron@gmx.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcp] Fix definitions for x86_64 and EFI BC client architectures
There has been a longstanding disagreement between RFC4578 and the
IANA "Processor Architecture Types" registry. RFC4578 section 2.1
defines type 7 as "EFI BC" and type 9 as "EFI x86-64"; the IANA
registry quotes RFC4578 as its source but has these values erroneously
swapped. The EDK2 codebase uses the IANA values.
As of March 2016, RFC4578 has been modified by an errata to match the
values as recorded in the IANA registry.
Fix our definitions to match the consensus values.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Use a timer event to generate the currticks() timer
We currently use the EFI_CPU_ARCH_PROTOCOL's GetTimerValue() method to
generate the currticks() timer, calibrated against a 1ms delay from
the boot services Stall() method.
This does not work on ARM platforms, where GetTimerValue() is an empty
stub which just returns EFI_UNSUPPORTED.
Fix by instead creating a periodic timer event, and using this event
to increment a current tick counter.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcpip] Do not fall back to using unoptimised TCP/IP checksumming
Require architecture-specific code to make a deliberate choice to use
the unoptimised generic_tcpip_continue_chksum() function, if there is
no optimised version available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This commit adds support for driving virtio 1.0 PCI devices. In
addition to various helpers, a number of vpm_ functions are introduced
to be used instead of their legacy vp_ counterparts when accessing
virtio 1.0 (aka modern) devices.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[virtio] Add virtio 1.0 constants and data structures
Virtio 1.0 introduces new constants and data structures, common to all
devices as well as specific to virtio-net. This commit adds a subset
of these to be able to drive the virtio-net 1.0 network device.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
PCI devices may support more capabilities of the same type (for
example PCI_CAP_ID_VNDR) and there was no way to discover all of them.
This commit adds a new API pci_find_next_capability which provides
this functionality. It would typically be used like so:
for (pos = pci_find_capability(pci, PCI_CAP_ID_VNDR);
pos > 0;
pos = pci_find_next_capability(pci, pos, PCI_CAP_ID_VNDR)) {
...
}
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[int13] Allow default drive to be specified via "san-drive" setting
The DHCP option 175.189 has been defined (by us) since 2006 as
containing the drive number to be used for a SAN boot, but has never
been automatically used as such by iPXE.
Use this option (if specified) to override the default SAN drive
number.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[int13] Allow drive to be hooked using the natural drive number
Interpret the maximum drive number (0xff for hard disks, 0x7f for
floppy disks) as meaning "use natural drive number".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown