Change the behaviour for adding DHCP options into a DHCP packet so
that we now append options, rather than insert them in front of
whatever options might already be present.
Apparently, the DHCP relay logic on a Nortel 470-48T layer 2 switch
cares about the order of DHCP options. If we build a DHCP packet
pre-populated with some options, their order will now be preserved,
except for encapsulated options.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Apparently, the DHCP relay logic on a Nortel 470-48T layer 2 switch
cares about the order of DHCP options. Specifically, it requires
that the DHCP message type option be the first option present in the
DHCP packet. We achieve this by having this option appear first in
our dhcp_request_options_data array, which pre-populates DHCP
requests.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[prefix] Add .hrom prefix for a ROM that loads high under PCI3 without PMM
gPXE currently takes advantage of the feature of PCI3.0 that allows
option ROMs to relocate the bulk of their code to high memory and so
take up only a small amount of space in the option ROM area. Currently,
the relocation can only take place if the BIOS's implementation of PMM
can be made to return blocks aligned to an even megabyte, because of
the A20 gate. AMI BIOSes, in particular, will not return allocations
that gPXE can use.
Ameliorate the situation somewhat by adding a prefix, .hrom, that works
identically to .rom except in the case that PMM allocation fails. Where
.rom would give up and place itself entirely in option ROM space, .hrom
moves to a block (assumed free) at HIGHMEM_LOADPOINT = 4MB. This allows
for the use of larger gPXE ROMs than would otherwise be possible.
Because there is no way to check that the area at HIGHMEM_LOADPOINT is
really free, other devices using that memory during the boot process
will cause failure for gPXE, the other device, or both. In practice
such conflicts will likely not occur, but this prefix should still be
considered EXPERIMENTAL.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[myri10ge] Native driver for Myricom 10Gb Ethernet NICs
This driver supports all current Myricom 10 gigabit Ethernet NICs.
It was written from scratch for gPXE by Glenn Brown <glenn@myri.com>,
referenencing Myricom's Linux and EFI drivers, with permission.
Signed-off-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[802.11] Allow connecting to spectrum managed networks
Contrary to the IEEE specification, some access points apparently
set the Spectrum Mgmt bit in the capabilities field even when
broadcasting on a 2.4GHz band that does not require spectrum
management. Allow gPXE to attempt to connect to such networks;
if spectrum management is really required, our advertisement
of capabilities not including it will result in an association
failure.
Reported-by: Peter Meyer <residue@xmail.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Wireless gPXE images are already so large that user-friendliness
seems to trump ROM-size friendliness in this case.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[eapol] Add basic support for 802.1X EAP over LANs
EAPOL is a container protocol that can wrap either EAP packets or
802.11 EAPOL-Key frames. For cleanliness' sake, add a stub that strips
the framing and sends packets off to the appropriate handler if it
is compiled in.
Signed-off-by: Marty Connor <mdc@etherboot.org>
WEP is a highly flawed cryptosystem, barely better than no encryption at all,
but many people still use it. It does have the advantage of being very simple
and small in code size.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[iwmgmt] Add wireless management commands and text for common errors
Add commands `iwstat' (to list 802.11-specific status information for
802.11 devices) and `iwlist' (to scan for available networks and print
a list along with security information).
Signed-off-by: Marty Connor <mdc@etherboot.org>
[crypto] Add parentheses around len argument in blocksize assert
This fixes an issue where passing a length as a compound expression
(e.g. using `hdrlen + datalen') would trigger compiler warnings and
potentially precedence-related errors.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[digest] Add HMAC-SHA1 based pseudorandom function and PBKDF2
Both of these routines are used by 802.11 WPA, but they are generic
and could be needed by other protocols as well.
Signed-off-by: Marty Connor <mdc@etherboot.org>
The disk partition prefix code in hdprefix.S reads the gPXE image in
tracks, not individual sectors. This means it will attempt to read
beyond the end of the image if the .hd image type is not padded to 32
KB.
This issue is affects virtualization software which may execute a .hd or
.usb image file directly - effectively running a machine with a tiny
disk containing just the gPXE image. Boot will fail when gPXE tries to
read beyond the end of disk.
[multiboot] Build memory map after shutting down and unhiding gPXE
The Multiboot memory map needs to be built after unhiding gPXE and
downloaded images from memory. Solaris faults during boot when trying
to access the ramdisk, which is hidden from the memory map while gPXE is
executing. This issue is fixed by using the memory map from after gPXE
unhides itself.
Reported-by: Moinak Ghosh <moinakg@belenix.org>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
[e1000] Use the alternate MAC in NVRAM when available
The 82571 supports an alternate MAC address location in NVRAM.
When this is set, use this for the MAC rather than the default
physical MAC address.
Ported from linux-2.6.git 93ca161027
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[e820mangler] Add missing CLC ins. for success path
The get_underlying_e820 function should return with CF unset on success.
Reported-by: Timothy Stack <tstack@vmware.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[linker] Add mechanism for subsystem-dependent configuration options
It is often the case that some module of gPXE is only relevant if the
subsystem it depends on is already being included. For instance,
commands to manage wireless interfaces are quite useless if no
compiled-in driver has pulled in the wireless networking stack. There
may be a user-modifiable configuration options for these dependent
modules, but even if enabled, they should not be included when they
would be useless.
Solve this by allowing the creation of config_subsystem.c, for
configuration directives like those in the global config.c that should
only be considered when subsystem.c is included in the final gPXE
build.
For consistency, move core/config.c to the config/ directory, where
the other config_subsystem.c files will eventually reside.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[linker] Expand and correct symbol requirement macros
REQUIRE_SYMBOL() formerly used a formulation of symbol requirement
that would allow a link to succeed despite lacking a required symbol,
because it did not introduce any relocations. Fix by renaming it to
REQUEST_SYMBOL() (since the soft-requirement behavior can be useful)
and add a REQUIRE_SYMBOL() that truly requires.
Add EXPORT_SYMBOL() and IMPORT_SYMBOL() for REQUEST_SYMBOL()-like
behavior that allows one to make use of the symbol, by combining a
weak external on the symbol itself with a REQUEST_SYMBOL() of a second
symbol.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[pxebs] Consistently interpret PXE type field as little-endian
The PXE menu code also treated the type as big-endian, which went
unnoticed until the first fix because its ntohs() was matched by a
htons() in the PXE boot server discovery code.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[int13] Guard against BIOSes that "fix" the drive count
Some BIOSes (observed with an AMI BIOS on a SunFire X2200) seem to
reset the BIOS drive counter at 40:75 after a failed boot attempt.
This causes problems when attempting a Windows direct-to-iSCSI
installation: bootmgr.exe calls INT 13,0800 and gets told that there
are no hard disks, so never bothers to read the MBR in order to obtain
the boot disk signature. The Windows iSCSI initiator will detect the
iBFT and connect to the target, and everything will appear to work
except for the error message "This computer's hardware may not support
booting to this disk. Ensure that the disk's controller is enabled in
the computer's BIOS menu."
Fix by checking the BIOS drive counter on every INT 13 call, and
updating it whenever necessary.
[autoboot] Ensure that an error message is always printed for a boot failure
The case of an unsupported SAN protocol will currently not result in
any error message. Fix by printing the error message at the top level
using strerror(), rather than using hard-coded error messages in the
error paths.
[susieq] Update qib_genbits.pl to handle SusieQ definitions
The latest RTL-generated register lists include (mostly redundant)
xxx_MSB values alongside xxx_LSB and xxx_RMASK, and also include
default register values.
Some subnet managers expect the GetResponse from a SetPortInfo MAD to
contain the new link state. The transition is not immediate, so we
often end up returning the previous link state. This can cause the SM
to fail to activate the port.
Fix by waiting for up to 20us for the link state transition to take
effect.
[ipoib] Mask out non-QPN bits in the IPoIB destination MAC when sending
The first byte of the IPoIB MAC address is used for flags indicating
support for "connected mode". Strip out the non-QPN bits of the first
dword when constructing the address vector for transmitted IPoIB
packets, so as not to end up passing an invalid QPN in the BTH.
[infiniband] Make node description invariant across all ports
IBA section 14.2.5.2 states that "the contents of the NodeDescription
attribute are the same for all ports on a node". Satisfy this by
using the HCA GUID rather than the port GUID to form the node
description string.
[ipv4] Ignore non-open net devices when performing routing
We do not discard routing table entries when closing an interface. It
is plausible that multiple interfaces may be on the same physical
network; if so, then we may end up in a situation whereby outbound
packets attempt to route via a closed interface.
Fix by ignoring non-open net devices in ipv4_route().
Shao Miller