[stp] Add support for detecting Spanning Tree Protocol non-forwarding ports
A fairly common end-user problem is that the default configuration of
a switch may leave the port in a non-forwarding state for a
substantial length of time (tens of seconds) after link up. This can
cause iPXE to time out and give up attempting to boot.
We cannot force the switch to start forwarding packets sooner, since
any attempt to send a Spanning Tree Protocol bridge PDU may cause the
switch to disable our port (if the switch happens to have the Bridge
PDU Guard feature enabled for the port).
For non-ancient versions of the Spanning Tree Protocol, we can detect
whether or not the port is currently forwarding and use this to inform
the network device core that the link is currently blocked.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Add a generic concept of a "blocked link"
When Spanning Tree Protocol (STP) is used, there may be a substantial
delay (tens of seconds) from the time that the link goes up to the
time that the port starts forwarding packets.
Add a generic concept of a "blocked link" (i.e. a link which is up but
which is not expected to communicate successfully), and allow "ifstat"
to indicate when a link is blocked.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Add support for mailbox used by virtual functions
Virtual functions use a mailbox to communicate with the physical
function driver: this covers functionality such as obtaining the MAC
address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When USB network card drivers are used, the BIOS' legacy USB
capability is necessarily disabled since there is no way to share the
host controller between the BIOS and iPXE. This currently results in
USB keyboards becoming non-functional in USB-enabled builds of iPXE.
Fix by adding basic support for USB keyboards, enabled by default in
iPXE builds which include USB support.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Maintain single lists of halted endpoints and changed ports
When an EHCI hotplug action results in the controller disowning the
port, it will result in a hotplug action on the corresponding UHCI or
OHCI controller. Allow such hotplug actions to be carried out as part
of the same call to usb_step() or usb_register_bus(), by maintaining a
single central list of changed ports.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The USB core will currently fail to detect disconnections if a new
device has attached by the time the port is examined in
usb_hotplug().
Fix by recording the fact that a disconnection has taken place
whenever the "connection status changed" (CSC) bit is observed to be
set. (Whether the change represents a disconnection or a
reconnection, it indicates that the port has experienced some time of
being disconnected.)
Note that the time at which a disconnection can be detected varies by
hub type. In particular: root hubs can observe the CSC bit when
polling, and so will record the disconnection before calling
usb_port_changed(), but USB hubs read the port status (and hence the
CSC bit) only during the call to hub_speed(), long after the call to
usb_port_changed().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pci] Provide PCI_CLASS() to calculate a scalar PCI class value
Rename PCI_CLASS() (which constructs a struct pci_class_id) to
PCI_CLASS_ID(), and provide PCI_CLASS() as a macro which constructs
the 24-bit scalar value of a PCI class code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Include setup packet within I/O buffer for message transfers
The USB API currently assumes that host controllers will have
immediate data buffer space available in which to store the setup
packet. This is true for xHCI, partially true for EHCI (which happens
to have 12 bytes of padding in each transfer descriptor due to
alignment requirements), and not true at all for UHCI.
Include the setup packet within the I/O buffer passed to the host
controller's message() method, thereby eliminating the requirement for
host controllers to provide immediate data buffers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[base16] Add buffer size parameter to base16_encode() and base16_decode()
The current API for Base16 (and Base64) encoding requires the caller
to always provide sufficient buffer space. This prevents the use of
the generic encoding/decoding functionality in some situations, such
as in formatting the hex setting types.
Implement a generic hex_encode() (based on the existing
format_hex_setting()), implement base16_encode() and base16_decode()
in terms of the more generic hex_encode() and hex_decode(), and update
all callers to provide the additional buffer length parameter.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Use the EFI_RNG_PROTOCOL as an entropy source if available
Entropy gathering via timer ticks is slow under UEFI (of the order of
20-30 seconds on some machines). Use the EFI_RNG_PROTOCOL if
available, to speed up the process of entropy gathering.
Note that some implementations (including EDK2) will fail if we
request fewer than 32 random bytes at a time, and that the RNG
protocol provides no guarantees about the amount of entropy provided
by a call to GetRNG(). We take the (hopefully pessimistic) view that
a 32-byte block returned by GetRNG() will contain at least the 1.3
bits of entropy claimed by min_entropy_per_sample().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-512/224 is almost identical to SHA-512, with differing initial
hash values and a truncated output length.
This implementation has been verified using the NIST SHA-512/224 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-512/256 is almost identical to SHA-512, with differing initial
hash values and a truncated output length.
This implementation has been verified using the NIST SHA-512/256 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-384 is almost identical to SHA-512, with differing initial hash
values and a truncated output length.
This implementation has been verified using the NIST SHA-384 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-224 is almost identical to SHA-256, with differing initial hash
values and a truncated output length.
This implementation has been verified using the NIST SHA-224 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[xhci] Support USB1 devices attached via transaction translators
xHCI provides a somewhat convoluted mechanism for specifying details
of a transaction translator. Hubs must be marked as such in the
device slot context. The only opportunity to do so is as part of a
Configure Endpoint command, which can be executed only when opening
the hub's interrupt endpoint.
We add a mechanism for host controllers to intercept the opening of
hub devices, providing xHCI with an opportunity to update the internal
device slot structure for the corresponding USB device to indicate
that the device is a hub. We then include the hub-specific details in
the input context whenever any Configure Endpoint command is issued.
When a device is opened, we record the device slot and port for its
transaction translator (if any), and supply these as part of the
Address Device command.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Reset endpoints without waiting for a new transfer to be enqueued
The current endpoint reset logic defers the reset until the caller
attempts to enqueue a new transfer to that endpoint. This is
insufficient when dealing with endpoints behind a transaction
translator, since the transaction translator is a resource shared
between multiple endpoints.
We cannot reset the endpoint as part of the completion handling, since
that would introduce recursive calls to usb_poll(). Instead, we
add the endpoint to a list of halted endpoints, and perform the reset
on the next call to usb_step().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several of the USB timeouts were chosen on the principle of "pick an
arbitrary but ridiculously large value, just to be safe". It turns
out that some of the timeouts permitted by the USB specification are
even larger: for example, control transactions are allowed to take up
to five seconds to complete.
Fix up these USB timeout values to match those found in the USB2
specification.
Debugged-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcp] Implement support for TCP Selective Acknowledgements (SACK)
The TCP Selective Acknowledgement option (specified in RFC2018)
provides a mechanism for the receiver to indicate packets that have
been received out of order (e.g. due to earlier dropped packets).
iPXE often operates in environments in which there is a high
probability of packet loss. For example, the legacy USB keyboard
emulation in some BIOSes involves polling the USB bus from within a
system management interrupt: this introduces an invisible delay of
around 500us which is long enough for around 40 full-length packets to
be dropped. Similarly, almost all 1Gbps USB2 devices will eventually
end up dropping packets because the USB2 bus does not provide enough
bandwidth to sustain a 1Gbps stream, and most devices will not provide
enough internal buffering to hold a full TCP window's worth of
received packets.
Add support for sending TCP Selective Acknowledgements. This provides
the sender with more detailed information about which packets have
been lost, and so allows for a more efficient retransmission strategy.
We include a SACK-permitted option in our SYN packet, since
experimentation shows that at least Linux peers will not include a
SACK-permitted option in the SYN-ACK packet if one was not present in
the initial SYN. (RFC2018 does not seem to mandate this behaviour,
but it is consistent with the approach taken in RFC1323.) We ignore
any received SACK options; this is safe to do since SACK is only ever
advisory and we never have to send non-trivial amounts of data.
Since our TCP receive queue is a candidate for cache discarding under
low memory conditions, we may end up discarding data that has been
reported as received via a SACK option. This is permitted by RFC2018.
We follow the stricture that SACK blocks must not report data which is
no longer held by the receiver: previously-reported blocks are
validated against the current receive queue before being included
within the current SACK block list.
Experiments in a qemu VM using forced packet drops (by setting
NETDEV_DISCARD_RATE to 32) show that implementing SACK improves
throughput by around 400%.
Experiments with a USB2 NIC (an SMSC7500) show that implementing SACK
improves throughput by around 700%, increasing the download rate from
35Mbps up to 250Mbps (which is approximately the usable bandwidth
limit for USB2).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smsc75xx] Add driver for SMSC/Microchip LAN75xx USB Ethernet NICs
This driver is functional but any downloads via a TCP-based protocol
tend to perform poorly. The 1Gbps Ethernet line rate is substantially
higher than the 480Mbps (in practice around 280Mbps) provided by USB2,
and the device has only 32kB of internal buffer memory. Our 256kB TCP
receive window therefore rapidly overflows the RX FIFO, leading to
multiple dropped packets (usually within the same TCP window) and
hence a low overall throughput.
Reducing the TCP window size so that the RX FIFO does not overflow
greatly increases throughput, but is not a general-purpose solution.
Further investigation is required to determine how other OSes
(e.g. Linux) cope with this scenario. It is possible that
implementing TCP SACK would provide some benefit.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most devices expose at least the link up/down status via a bit in a
MAC register, since the MAC generally already needs to know whether or
not the link is up. Some devices (e.g. the SMSC75xx USB NIC) expose
this information to software only via the MII registers.
Provide a generic mii_check_link() implementation to check the BMSR
and report the link status via netdev_link_{up,down}().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[legal] Relicense files under GPL2_OR_LATER_OR_UBDL
Relicense files with kind permission from
Stefan Hajnoczi <stefanha@redhat.com>
alongside the contributors who have already granted such relicensing
permission.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Rewrite (and relicense) the header files which are included in all
builds of iPXE (including non-Linux builds).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At some point in the past few years, binutils became more aggressive
at removing unused symbols. To function as a symbol requirement, a
relocation record must now be in a section marked with @progbits and
must not be in a section which gets discarded during the link (either
via --gc-sections or via /DISCARD/).
Update REQUIRE_SYMBOL() to generate relocation records meeting these
criteria. To minimise the impact upon the final binary size, we use
existing symbols (specified via the REQUIRING_SYMBOL() macro) as the
relocation targets where possible. We use R_386_NONE or R_X86_64_NONE
relocation types to prevent any actual unwanted relocation taking
place. Where no suitable symbol exists for REQUIRING_SYMBOL() (such
as in config.c), the macro PROVIDE_REQUIRING_SYMBOL() can be used to
generate a one-byte-long symbol to act as the relocation target.
If there are versions of binutils for which this approach fails, then
the fallback will probably involve killing off REQUEST_SYMBOL(),
redefining REQUIRE_SYMBOL() to use the current definition of
REQUEST_SYMBOL(), and postprocessing the linked ELF file with
something along the lines of "nm -u | wc -l" to check that there are
no undefined symbols remaining.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown