[efi] Add a USB host controller driver based on EFI_USB_IO_PROTOCOL
Allow iPXE to coexist with other USB device drivers, by attaching to
the EFI_USB_IO_PROTOCOL instances provided by the UEFI platform
firmware.
The EFI_USB_IO_PROTOCOL is an unsurprisingly badly designed
abstraction of a USB device. The poor design choices intrinsic in the
UEFI specification prevent efficient operation as a network device,
with the result that devices operated using the EFI_USB_IO_PROTOCOL
operate approximately two orders of magnitude slower than devices
operated using our native EHCI or xHCI host controller drivers.
Since the performance is so abysmally slow, and since the underlying
problems are due to fundamental architectural mistakes in the UEFI
specification, support for the EFI_USB_IO_PROTOCOL host controller
driver is left as disabled by default. Users are advised to use the
native iPXE host controller drivers instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Many UEFI NBPs expect to find an EFI_PXE_BASE_CODE_PROTOCOL installed
in addition to the EFI_SIMPLE_NETWORK_PROTOCOL. Most NBPs use the
EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the cached DHCP packets.
This implementation has been tested with grub.efi, shim.efi,
syslinux.efi, and wdsmgfw.efi. Some methods (such as Discover() and
Arp()) are not used by any known NBP and so have not (yet) been
implemented.
Usage notes for the tested bootstraps are:
- grub.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet, and uses no other methods.
- shim.efi uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the cached
DHCP packet and to retrieve the next NBP via the Mtftp() method.
If shim.efi was downloaded via HTTP (or other non-TFTP protocol)
then shim.efi will blindly call Mtftp() with an HTTP URI as the
filename: this allows the next NBP (e.g. grubx64.efi) to also be
transparently retrieved by HTTP.
shim.efi can also use the EFI_SIMPLE_FILE_SYSTEM_PROTOCOL to
retrieve files previously loaded by "imgfetch" or similar commands
in iPXE. The current implementation of shim.efi will use the
EFI_SIMPLE_FILE_SYSTEM_PROTOCOL only if it does not find an
EFI_PXE_BASE_CODE_PROTOCOL; this patch therefore prevents this
usage of our EFI_SIMPLE_FILE_SYSTEM_PROTOCOL. This logic could be
trivially reversed in shim.efi if needed.
- syslinux.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet. Versions 6.03 and earlier have a bug which
may cause syslinux.efi to attach to the wrong NIC if there are
multiple NICs in the system (or if the UEFI firmware supports
IPv6).
- wdsmgfw.efi (ab)uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the
cached DHCP packets, and to send and retrieve UDP packets via the
UdpWrite() and UdpRead() methods. (This was presumably done in
order to minimise the amount of benefit obtainable by switching to
UEFI, by replicating all of the design mistakes present in the
original PXE specification.)
The EFI_DOWNGRADE_UX configuration option remains available for now,
until this implementation has received more widespread testing.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge the functionality of parse_next_server_and_filename() and
tftp_uri() into a single pxe_uri(), which takes a server address
(IPv4/IPv6/none) and a filename, and produces a URI using the rule:
- if the filename is a hierarchical absolute URI (i.e. includes a
scheme such as "http://" or "tftp://") then use that URI and ignore
the server address,
- otherwise, if the server address is recognised (according to
sa_family) then construct a TFTP URI based on the server address,
port, and filename
- otherwise fail.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Add definitions of GUIDs observed when booting wdsmgfw.efi
Add definitions of protocols observed to be used by wdsmgfw.efi, and
add a handle name type for ConIn, ConOut, and StdErr.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add debug wrappers for more boot services functions, and print
symbolic values rather than raw numbers where possible.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 09b057c ("[settings] Remove "uristring" setting type") removed
support for URI-encoded settings via the "uristring" setting type, on
the basis that such encoding was no longer necessary to avoid problems
with the command line parser.
Other valid use cases for the "uristring" setting type do exist: for
example, a password containing a '/' character expanded via
chain http://username:${password:uristring}@server.name/boot.php
Restore the existence of the "uristring" setting, avoiding the
potentially large stack allocations that were used in the old code
prior to commit 09b057c ("[settings] Remove "uristring" setting
type").
Requested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[image] Detect image type when image is first registered
The current usage pattern of image_probe() is a legacy from the time
before commit 34b6ecb ("[image] Simplify image management") when
loading an image to its executable location in memory was a separate
action from actually executing the image.
Call image_probe() as soon as an image is registered. This allows
"imgstat" to display image type information for all images and allows
image-consuming code to assume that image->type is already set
correctly.
Ignore failures if image_probe() does not recognise the image, since
we do expect to handle unrecognised images (initrds, modules, etc).
Unrecognised images will be left with a NULL image->type, which
image-consuming code can easily check.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[test] Allow self-tests to report exit status when running under Linux
Allow the return status from an embedded image to propagate out to the
eventual return status from main(). When running under Linux, this
allows the pass/fail result of unit tests to be observable without
having to visually inspect the console output.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[http] Rewrite HTTP core to support content encodings
Rewrite the HTTP core to allow for the addition of arbitrary content
encoding mechanisms, such as PeerDist and gzip.
The core now exposes http_open() which can be used to create requests
with an explicitly selected HTTP method, an optional requested content
range, and an optional request body. A simple wrapper provides the
preexisting behaviour of creating either a GET request or an
application/x-www-form-urlencoded POST request (if the URI includes
parameters).
The HTTP SAN interface is now implemented using the generic block
device translator. Individual blocks are requested using http_open()
to create a range request.
Server connections are now managed via a connection pool; this allows
for multiple requests to the same server (e.g. for SAN blocks) to be
completely unaware of each other. Repeated HTTPS connections to the
same server can reuse a pooled connection, avoiding the per-connection
overhead of establishing a TLS session (which can take several seconds
if using a client certificate).
Support for HTTP SAN booting and for the Basic and Digest
authentication schemes is now optional and can be controlled via the
SANBOOT_PROTO_HTTP, HTTP_AUTH_BASIC, and HTTP_AUTH_DIGEST build
configuration options in config/general.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
UEFI platforms may provide a watchdog timer, which will reboot the
machine if an operating system takes more than five minutes to load.
This can cause long-lived iPXE downloads (or interactive shell
sessions) to unexpectedly reboot.
Fix by resetting the watchdog timer every ten seconds while the iPXE
main processing loop continues to run.
Reported-by: Bradley B Williams <bradleybwilliams@swbell.net>
Reported-by: John Clark <john.r.clark.3@gmail.com>
Reported-by: wdriever@gmail.com
Reported-by: Charlie Beima <cbeima@indiana.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Support SHA-{224,384,512} in X.509 certificates
Add support for SHA-224, SHA-384, and SHA-512 as digest algorithms in
X.509 certificates, and allow the choice of public-key, cipher, and
digest algorithms to be configured at build time via config/crypto.h.
Originally-implemented-by: Tufan Karadere <tufank@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[serial] Check for UART existence in uart_select()
Check for existence of the UART in uart_select(), not just in
uart_init(). This allows uart_select() to refuse to set a non-working
address in uart->base, which in turns means that the serial console
code will not attempt to use a non-existent UART.
Reported-by: Torgeir Wulfsberg <Torgeir.Wulfsberg@kongsberg.com>
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We do not set up any kind of virtual addressing before invoking an
ELFBoot image. Reject if the image's program headers indicate that
virtual addresses are not equal to physical addresses.
This avoids problems when loading some RHEL5 kernels, which seem to
include ELFBoot headers using virtual addressing. With this change,
these kernels are no longer detected as ELFBoot, and so may be
(correctly) detected as bzImage instead.
Reported-by: Torgeir.Wulfsberg@kongsberg.com
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow line buffer to accumulate multiple lines, with buffered_line()
returning each freshly-completed line as it is encountered. This
allows buffered lines to be subsequently processed as a group.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Allow network devices to disclaim IRQ support at runtime
VLAN and 802.11 devices use a network device operations structure that
wraps an underlying structure. For example, the vlan_operations
structure wraps the network device operations structure of the
underlying trunk device. This can cause false positives from the
current implementation of netdev_irq_supported(), which will always
report that VLAN devices support interrupts since it has no visibility
into the support provided by the underlying trunk device.
Fix by allowing network devices to explicitly flag that interrupts are
not supported, despite the presence of an irq() method.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv4] Allow IPv4 socket addresses to include a scope ID
Extend the IPv6 concept of "scope ID" (indicating the network device
index) to IPv4 socket addresses, so that IPv4 multicast transmissions
may specify the transmitting network device.
The scope ID is not (currently) exposed via the string representation
of the socket address, since IPv4 does not use the IPv6 concept of
link-local addresses (which could legitimately be specified in a URI).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv4] Redefine IP address constants to avoid unnecessary byte swapping
Redefine various IPv4 address constants and testing macros to avoid
unnecessary byte swapping at runtime, and slightly rename the macros
to prevent code from accidentally using the old definitions.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv6] Treat a missing network device name as "netX"
When an IPv6 socket address string specifies a link-local or multicast
address but does not specify the requisite network device name
(e.g. "fe80::69ff:fe50:5845" rather than "fe80::69ff:fe50:5845%net0"),
assume the use of "netX".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the AES implementation from AXTLS with a dedicated iPXE
implementation which is slightly smaller and around 1000% faster.
This implementation has been verified using the existing self-tests
based on the NIST AES test vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce the cost of implementing object methods which convey no
information beyond the fact that the method has been called.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[profile] Add profile_custom() for profiling with arbitrary time units
Provide profile_custom() as a trivial wrapper around profile_update()
to allow for the use of the profiling infrastructure by code using
timers other than the default profile_timestamp() provider.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[fault] Add inject_corruption() to randomly corrupt data
Provide an inject_corruption() function that can be used to randomly
corrupt data bytes with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a generic inject_fault() function that can be used to inject
random faults with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Fix receive and transmit completion reporting
Fix the TxBuf value filled in by GetStatus() to report the transmit
buffer address as required by the (now clarified) specification.
Simplify "interrupt" handling in GetStatus() to report only that one
or more packets have been transmitted or received; there is no need to
report one GetStatus() "interrupt" per packet.
Simplify receive handling to dequeue received packets immediately from
the network device into an internal list (thereby avoiding the hacks
previously used to determine when to report new packet arrivals).
Originally-fixed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcp] Gracefully close connections during shutdown
We currently do not wait for a received FIN before exiting to boot a
loaded OS. In the common case of booting from an HTTP server, this
means that the TCP connection is left consuming resources on the
server side: the server will retransmit the FIN several times before
giving up.
Fix by initiating a graceful close of all TCP connections and waiting
(for up to one second) for all connections to finish closing
gracefully (i.e. for the outgoing FIN to have been sent and ACKed, and
for the incoming FIN to have been received and ACKed at least once).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipoib] Attempt to generate ARPs as needed to repopulate REMAC cache
The only way to map an eIPoIB MAC address (REMAC) to an IPoIB MAC
address is to intercept an incoming ARP request or reply.
If we do not have an REMAC cache entry for a particular destination
MAC address, then we cannot transmit the packet. This can arise in at
least two situations:
- An external program (e.g. a PXE NBP using the UNDI API) may attempt
to transmit to a destination MAC address that has been obtained by
some method other than ARP.
- Memory pressure may have caused REMAC cache entries to be
discarded. This is fairly likely on a busy network, since REMAC
cache entries are created for all received (broadcast) ARP
requests. (We can't sensibly avoid creating these cache entries,
since they are required in order to send an ARP reply, and when we
are being used via the UNDI API we may have no knowledge of which
IP addresses are "ours".)
Attempt to ameliorate the situation by generating a semi-spurious ARP
request whenever we find a missing REMAC cache entry. This will
hopefully trigger an ARP reply, which would then provide us with the
information required to populate the REMAC cache.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown