Provide a generic inject_fault() function that can be used to inject
random faults with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE does not currently provide EFI_PXE_BASE_CODE_PROTOCOL: this
causes failures when chainloading bootloaders such as shim.efi which
assume that this protocol will be present.
Provide the ability to work around these problems via the build
configuration option EFI_DOWNGRADE_UX. If this option is enabled,
then we will not install our usual EFI_LOAD_FILE_PROTOCOL
implementation, thereby allowing the platform firmware to install its
own EFI_PXE_BASE_CODE_PROTOCOL implementation on top of our
EFI_SIMPLE_NETWORK_PROTOCOL handle.
A somewhat major side-effect of this workaround is that almost all
iPXE features will be disabled.
This configuration option will be removed in future when support for
EFI_PXE_BASE_CODE_PROTOCOL is added.
Requested-by: Laszlo Ersek <lersek@redhat.com>
Requested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[stp] Add support for detecting Spanning Tree Protocol non-forwarding ports
A fairly common end-user problem is that the default configuration of
a switch may leave the port in a non-forwarding state for a
substantial length of time (tens of seconds) after link up. This can
cause iPXE to time out and give up attempting to boot.
We cannot force the switch to start forwarding packets sooner, since
any attempt to send a Spanning Tree Protocol bridge PDU may cause the
switch to disable our port (if the switch happens to have the Bridge
PDU Guard feature enabled for the port).
For non-ancient versions of the Spanning Tree Protocol, we can detect
whether or not the port is currently forwarding and use this to inform
the network device core that the link is currently blocked.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Allow autoboot device filter to be disabled
Our current behaviour when booting as a ROM is to autoboot only from
devices which are attached via the PCI bus:dev.fn address passed to
the ROM's initialisation vector.
Add a build configuration option AUTOBOOT_ROM_FILTER (enabled by
default) to control this behaviour. This allows for ROMs to be built
which will attempt to boot from any detected device, even if not
attached via the original PCI bus:dev.fn address. (This is
particularly useful when building combined EHCI/xHCI ROMs for USB
network boot, since the BIOS may request a boot via the EHCI
controller but the xHCI driver will reroute the root hub ports to the
xHCI controller.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[legal] Relicense files under GPL2_OR_LATER_OR_UBDL
These files cannot be automatically relicensed by util/relicense.pl
since they either contain unusual but trivial contributions (such as
the addition of __nonnull function attributes), or contain lines
dating back to the initial git revision (and so require manual
knowledge of the code's origin).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Allow for named configurations at build time
Allow named configurations to be specified via the CONFIG=... build
parameter. For headers in config/*.h which support named
configurations, the following files will be included when building
with CONFIG=<name>:
- config/defaults/<platform>.h (e.g. config/defaults/pcbios.h)
- config/<header>.h
- config/<name>/<header>.h (only if the directory config/<name> exists)
- config/local/<header>.h (autocreated if necessary)
- config/local/<name>/<header>.h (autocreated if necessary)
This mechanism allows for predefined named configurations to be
checked in to the source tree, as a directory config/<name> containing
all of the required header files.
The mechanism also allows for users to define multiple local
configurations, by creating header files in the directory
config/local/<name>.
Note that the config/*.h files which are used only to configure
internal iPXE APIs (e.g. config/ioapi.h) cannot be modified via a
named configuration. This avoids rebuilding the entire iPXE codebase
whenever switching to a different named configuration.
Inspired-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Allow ROM banner timeout to be configured independently
iPXE currently prints a "Press Ctrl-B" banner twice: once when the ROM
is first called for initialisation and again if we attempt to boot
from the ROM. This slows boot, especially when the NIC is not the
primary boot device. Tools such as libguestfs make use of QEMU VMs
for performing maintenance on disk images and may make use of NICs in
the VM for network support. If iPXE introduces a static init-time
delay, that directly translates to increased runtime for the tools.
Fix by allowing the ROM banner timeout to be configured independently
of the main banner timeout.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the existing partially-implemented IPv6 stack with a fresh
implementation.
This implementation is not yet complete. The IPv6 transmit and
receive datapaths are functional (including fragment reassembly and
parsing of arbitrary extension headers). NDP neighbour solicitations
and advertisements are supported. ICMPv6 echo is supported.
At present, only link-local addresses may be used, and there is no way
to specify an IPv6 address as part of a URI (either directly or via
a DNS lookup).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add "sync" command (loosely based on the Unix "sync"), which will wait
for any pending operations to complete.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The WinCE, a.out and FreeBSD loaders are designed to be #included by
core/loader.c, which no longer exists. These old loaders are not
usable anymore and cause compilation failures when enabled in
config/general.h.
Signed-off-by: Marin Hannache <mareo@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DOWNLOAD_PROTO_TFTM is now useless as tftm support has been merged
into tftp.c. DOWNLOAD_PROTO_TFTP should be used instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Do not fall back to hooking INT19 by default
Several BIOSes (including most IBM BIOSes and many virtual machine
BIOSes) do not provide detectable PnP support, but will use the BEV
entry point for a PnP option ROM. On these semi-PnP BIOSes, iPXE will
respond to the absence of detectable PnP support by hooking INT19,
which disrupts the boot order.
BIOSes that genuinely require hooking INT19 seem to be very rare
nowadays. It may therefore be preferable to assume that the absence
of detectable PnP support indicates a semi-PnP BIOS rather than a
non-PnP BIOS.
Change the default behaviour so that INT19 will never be hooked unless
the compile-time option NONPNP_HOOK_INT19 is enabled. Leave the
redundant PnP detection routine in-place to allow for debugging via
the ROM banner line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pxe] Remove startpxe and stoppxe commands from default builds
These commands exist primarily for debugging and are not generally
useful, so save 137 bytes by removing them by default.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Fibre Channel Protocol provides a mechanism for transporting SCSI
commands via a Fibre Channel fabric.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Provide a test mechanism for discarding packets at random
Setting NETDEV_DISCARD_RATE to a non-zero value will cause one in
every NETDEV_DISCARD_RATE packets to be discarded at random on both
the transmit and receive datapaths, allowing the robustness of
upper-layer network protocols to be tested even in simulation
environments that provide wholly reliable packet transmission.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include config/local/$file in config/$file where it makes sense and
create empty local configs during build if not present.
Modified-by: Michael Brown <mcb30@etherboot.org>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
The NMB protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The NFS protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
I have an unfinished NFSv3 over TCP implementation for gPXE that can be
used as the base for new work, should we want to resurrect this
protocol.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The FSP protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
For extremely tight space requirements and specific applications, it is
sometimes desirable to create gPXE images that cannot provide the PXE API
functionality to client programs. Add a configuration header option,
PXE_STACK, that can be removed to remove this stack. Also add PXE_MENU
to control the PXE boot menu, which most uses of gPXE do not need.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Wireless gPXE images are already so large that user-friendliness
seems to trump ROM-size friendliness in this case.
Signed-off-by: Marty Connor <mdc@etherboot.org>
WEP is a highly flawed cryptosystem, barely better than no encryption at all,
but many people still use it. It does have the advantage of being very simple
and small in code size.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[iwmgmt] Add wireless management commands and text for common errors
Add commands `iwstat' (to list 802.11-specific status information for
802.11 devices) and `iwlist' (to scan for available networks and print
a list along with security information).
Signed-off-by: Marty Connor <mdc@etherboot.org>
SRP is the SCSI RDMA Protocol. It allows for a method of SAN booting
whereby the target is responsible for reading and writing data using
Remote DMA directly to the initiator's memory. The software initiator
merely sends and receives SCSI commands; it never has to touch the
actual data.
Michael Brown