[ifmgmt] Do not sleep CPU while configuring network devices
iPXE currently calls cpu_nap() while performing DHCP, in order to
reduce CPU utilisation on virtual machines. Under mild broadcast load
(~100 packets per second), this can cause received packets to be
dropped because the receive descriptor ring is overrun before the next
18Hz timer interrupt wakes up the CPU. The result is that DHCP is
likely to intermittently fail on networks with appreciable amounts of
broadcast (or multicast) traffic.
This behaviour was introduced in the series of commits which
generalised the "dhcp" command to the "ifconf" command. The earlier
code (which did not handle IPv6 configuration) had no call to
cpu_nap() and so did not suffer from this problem.
Fix by removing the call to cpu_nap() in ifpoller_progress(). This
has the undesirable side effect that CPU utilisation will remain at
100% while waiting for DHCP to complete (which can take several
seconds, if we have to wait around for potential ProxyDHCP offers to
arrive).
Reported-by: Alex Davies <adavies@jumptrading.com>
Reported-by: Christoffer Stokbæk <christoffers@easyspeedy.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Allow network device to update link state before checking
If the network interface has only just been opened (e.g. by the "dhcp"
command) then we should allow at least one opportunity for the card to
update the link state before testing it, to avoid false positives.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Separate out the concept of hardware and link-layer addresses
The hardware address is an intrinsic property of the hardware, while
the link-layer address can be changed at runtime. This separation is
exposed via APIs such as PXE and EFI, but is currently elided by gPXE.
Expose the hardware and link-layer addresses as separate properties
within a net device. Drivers should now fill in hw_addr, which will
be used to initialise ll_addr at the time of calling
register_netdev().
[ifmgmt] Move link-up status messages from autoboot() to iflinkwait()
With the addition of link status codes, we can now display a detailed
error indication if iflinkwait() fails.
Putting the error output in iflinkwait avoids code duplication, and
gains symmetry with the other interface management routines; ifopen()
already prints an error directly if it cannot open its interface.
Modified-by: Michael Brown <mcb30@etherboot.org>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
[netdevice] Add mechanism for reporting detailed link status codes
Expand the NETDEV_LINK_UP bit into a link_rc status code field,
allowing specific reasons for link failure to be reported via
"ifstat".
Originally-authored-by: Joshua Oreman <oremanj@rwcr.net>
[netdevice] Retain and report detailed error breakdowns
netdev_rx_err() and netdev_tx_complete_err() get passed the error
code, but currently use it only in debug messages.
Retain error numbers and frequencey counts for up to
NETDEV_MAX_UNIQUE_ERRORS (4) different errors for each of TX and RX.
This allows the "ifstat" command to report the reasons for TX/RX
errors in most cases, even in non-debug builds.
Add ability for network devices to flag link up/down state to the
networking core.
Autobooting code will now wait for link-up before attempting DHCP.
IPoIB reflects the Infiniband link state as the network device link state
(which is not strictly correct; we also need a succesful IPoIB IPv4
broadcast group join), but is probably more informative.
Add "name" field to struct device to allow human-readable hardware device
names.
Add "dev" pointer in struct net_device to tie network interfaces back to a
hardware device.
Force natural alignment of data types in __table() macros. This seems to
prevent gcc from taking the unilateral decision to occasionally increase
their alignment (which screws up the table packing).
Strip down i386 PCI configuration space I/O to the bare minimum. A
typical build will now include 880 bytes of PCI support code, compared to
2327 bytes in Etherboot 5.4.
(There is a slight cost of around 5 extra bytes per access to a
non-constant config space address; this should be an overall win.
Driver-specific accesses will usually be to constant addresses, for
which there is no additional cost.)
Michael Brown