[tcpip] Do not fall back to using unoptimised TCP/IP checksumming
Require architecture-specific code to make a deliberate choice to use
the unoptimised generic_tcpip_continue_chksum() function, if there is
no optimised version available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcpip] Avoid generating positive zero for transmitted UDP checksums
TCP/IP checksum fields are one's complement values and therefore have
two possible representations of zero: positive zero (0x0000) and
negative zero (0xffff).
In RFC768, UDP over IPv4 exploits this redundancy to repurpose the
positive representation of zero (0x0000) to mean "no checksum
calculated"; checksums are optional for UDP over IPv4.
In RFC2460, checksums are made mandatory for UDP over IPv4. The
wording of the RFC is such that the UDP header is mandated to use only
the negative representation of zero (0xffff), rather than simply
requiring the checksum to be correct but allowing for either
representation of zero to be used.
In RFC1071, an example algorithm is given for calculating the TCP/IP
checksum. This algorithm happens to produce only the positive
representation of zero (0x0000); this is an artifact of the way that
unsigned arithmetic is used to calculate a signed one's complement
sum (and its final negation).
A common misconception has developed (exemplified in RFC1624) that
this artifact is part of the specification. Many people have assumed
that the checksum field should never contain the negative
representation of zero (0xffff).
A sensible receiver will calculate the checksum over the whole packet
and verify that the result is zero (in whichever representation of
zero happens to be generated by the receiver's algorithm). Such a
receiver will not care which representation of zero happens to be used
in the checksum field.
However, there are receivers in existence which will verify the
received checksum the hard way: by calculating the checksum over the
remainder of the packet and comparing the result against the checksum
field. If the representation of zero used by the receiver's algorithm
does not match the representation of zero used by the transmitter (and
so placed in the checksum field), and if the receiver does not
explicitly allow for both representations to compare as equal, then
the receiver may reject packets with a valid checksum.
For UDP, the combined RFCs effectively mandate that we should generate
only the negative representation of zero in the checksum field.
For IP, TCP and ICMP, the RFCs do not mandate which representation of
zero should be used, but the misconceptions which have grown up around
RFC1071 and RFC1624 suggest that it would be least surprising to
generate only the positive representation of zero in the checksum
field.
Fix by ensuring that all of our checksum algorithms generate only the
positive representation of zero, and explicitly inverting this in the
case of transmitted UDP packets.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Tested-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv4] Allow IPv4 socket addresses to include a scope ID
Extend the IPv6 concept of "scope ID" (indicating the network device
index) to IPv4 socket addresses, so that IPv4 multicast transmissions
may specify the transmitting network device.
The scope ID is not (currently) exposed via the string representation
of the socket address, since IPv4 does not use the IPv6 concept of
link-local addresses (which could legitimately be specified in a URI).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[legal] Relicense files under GPL2_OR_LATER_OR_UBDL
These files cannot be automatically relicensed by util/relicense.pl
since they either contain unusual but trivial contributions (such as
the addition of __nonnull function attributes), or contain lines
dating back to the initial git revision (and so require manual
knowledge of the code's origin).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcpip] Provide tcpip_mtu() to determine the maximum transmission unit
Provide the function tcpip_mtu() to allow external code to determine
the (transport-layer) maximum transmission unit for a given socket
address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcpip] Provide tcpip_netdev() to determine the transmitting network device
Provide the function tcpip_netdev() to allow external code to
determine the transmitting network device for a given socket address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcpip] Allow for architecture-specific TCP/IP checksum routines
Calculating the TCP/IP checksum on received packets accounts for a
substantial fraction of the response latency.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tables] Incorporate table data type information into table definition
Eliminate the potential for mismatches between table names and the
table entry data type by incorporating the data type into the
definition of the table, rather than specifying it explicitly in each
table accessor method.
[tables] Redefine methods for accessing linker tables
Intel's C compiler (icc) chokes on the zero-length arrays that we
currently use as part of the mechanism for accessing linker table
entries. Abstract away the zero-length arrays, to make a port to icc
easier.
Introduce macros such as for_each_table_entry() to simplify the common
case of iterating over all entries in a linker table.
Represent table names as #defined string constants rather than
unquoted literals; this avoids visual confusion between table names
and C variable or type names, and also allows us to force a
compilation error in the event of incorrect table names.
[tcpip] Allow for transmission to multicast IPv4 addresses
When sending to a multicast address, it may be necessary to specify
the source address explicitly, since the multicast destination address
does not provide enough information to deduce the source address via
the miniroute table.
Allow the source address specified via the data-xfer metadata to be
passed down through the TCP/IP stack to the IPv4 layer, which can use
it as a default source address.
[build] Avoid strict-aliasing warnings when building with gcc 4.4
Conventional usage of the various struct sockaddr_xxx types involves
liberal use of casting, which tends to trigger strict-aliasing
warnings from gcc. Avoid these now and in future by marking all the
relevant types with __attribute__((may_alias)).
Add "name" field to struct device to allow human-readable hardware device
names.
Add "dev" pointer in struct net_device to tie network interfaces back to a
hardware device.
Force natural alignment of data types in __table() macros. This seems to
prevent gcc from taking the unilateral decision to occasionally increase
their alignment (which screws up the table packing).
Michael Brown