From: Viswanath Krishnamurthy <viswa.krish@gmail.com>

The current ipv4 incorrectly checks the IP address for multicast address.
This causes valid IPv4 unicast address to be trated as multicast address

For e.g if the PXE/tftp server IP address is 192.168.4.XXX where XXX is
224 or greater, it gets treated as multicast address and a ethernet
multicast address is sent out on the wire causing timeouts

Some EMC targets will fail if we advertise that we can authenticate with
CHAP, but the target is configured to allow unauthenticated access to that
target.  We advertise AuthMethod=CHAP,None; the target should (I think)
select AuthMethod=None for unprotected targets.  IETD does this, but an
EMC Celerra NS83 doesn't.

Fix by offering only AuthMethod=None if the user hasn't supplied a
username and password; this means that we won't be offering CHAP
authentication unless the user is expecting to use it (in which case the
target is presumably configured appropriately).

Many thanks to Alessandro Iurlano <alessandro.iurlano@gmail.com> for
reporting and helping to diagnose this problem.

Infiniband devices no longer block waiting for link-up in
register_ibdev().

Hermon driver needs to create an event queue and poll for link-up events.

Infiniband core needs to reread MAD parameters when link state changes.

IPoIB needs to cope with Infiniband link parameters being only partially
available at probe and open time.

gPXE is not compliant with the HTTP/1.1 specification (RFC 2616),
since it lacks support for "Transfer-Encoding: chunked".  gPXE is,
however, compliant with the HTTP/1.0 specification (RFC 1945), which
does not require "Transfer-Encoding: chunked" to be supported.

The only HTTP/1.1 feature that gPXE uses is the "Host:" header, but
servers universally accept that one from HTTP/1.0 clients as an
optional extension (it is obligatory for HTTP/1.1).  gPXE does not,
for example, appear to support connection caching.  Advertising as a
HTTP/1.0 client will typically make the server close the connection
immediately upon sending the last data, which is actually beneficial
if we aren't going to keep the connection alive anyway.

In particular, expose the system UUID as a setting ("smbios/uuid").

The PXE spec is (as usual) unclear on precisely when ProxyDHCPREQUESTs
should be issued.  We adapt the following, slightly paranoid approach:

  If an offer contains an IP address, then it is a normal DHCPOFFER.

  If an offer contains an option #60 "PXEClient", then it is a
  ProxyDHCPOFFER.  Note that the same packet can be both a normal
  DHCPOFFER and a ProxyDHCPOFFER.

  After receiving the normal DHCPACK, if we have received a
  ProxyDHCPOFFER, we unicast a ProxyDHCPREQUEST back to the ProxyDHCP
  server on port 4011.  If we time out waiting for a ProxyDHCPACK, we
  treat this as a non-fatal error.

This avoids confusing other code by insisting that we have e.g. a
filename consisting of 128 zero bytes.

Copy DHCP responses to a standard malloc()ed buffer, rather than
retaining the I/O buffer that they arrived in.

Allow for settings to be described by something other than a DHCP option
tag if desirable.  Currently used only for the MAC address setting.

Separate out fake DHCP packet creation code from dhcp.c to fakedhcp.c.

Remove notion of settings from dhcppkt.c.

Rationalise dhcp.c to use settings API only for final registration of the
DHCP options, rather than using {store,fetch}_setting throughout.

DHCP code was using an incorrect check for whether to construct a
DHCPDISCOVER or DHCPREQUEST packet.

Add dedicated functions create_dhcpdiscover(), create_dhcpack() and
create_proxydhcpack() for use by external code such as the PXE preboot
code.

Register ProxyDHCP options under the global scope "proxydhcp".

Unregister previously-acquired DHCP and ProxyDHCP settings when DHCP
succeeds.

Convert DHCP option applicators in dns.c and iscsi.c to settings
applicators.

Kill off DHCP option applicators.

Add a configuration settings block for each net device.  This will
provide the parent scope for settings applicable only to that network
device (e.g. non-volatile options stored on the NIC, options obtained via
DHCP, etc.).

Expose the MAC address as a setting.

Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>

RFC 4390 provides for the DHCP client identifier to contain the link-layer
hardware type and MAC address when the MAC address exceeds 16 bytes.
However, the hardware type field is only 8 bits; we were assuming 16 bits.

Arbel and Hermon cards both have multiple ports.  Add the
infrastructure required to register each port as a separate IB
device.  Don't yet register more than one port, since registration
will currently fail unless a valid link is detected.

Use ib_*_{set,get}_{drv,owner}data wrappers to access driver- and
owner-private data on Infiniband structures.

Pull out common code for handling management datagrams from arbel.c
and hermon.c into infiniband.c.

Add port number to struct ib_device.

Add open(), close() and mad() methods to struct ib_device_operations.

  Allow port numbers in iSCSI redirection.

  Wait for SCSI status, not just the final data-in (which may be followed
  by an explicit SCSI Response PDU if the S bit is not set).

separate xfer method.

Add missing .alloc_iob entries to several xfer_interface_operations
structures.

their equivalent DHCP-option-specified values.

is non-functional anyway.

supply options.

also avoid waiting for ProxyDHCP offers).

Also reduce the ProxyDHCP timeout, because it's already irritating me.

We didn't specify values for MaxRecvDataSegmentLength and
MaxBurstLength (to save space, since we were happy with the
RFC-defined default values of 8kB and 256kB respectively).  However,
the OpenSolaris target (incorrectly) assumes default values of zero
for these parameters.

The upshot was that the OpenSolaris target would get stuck in an
endless loop trying to send us the first 512-byte sector, zero bytes
at a time, and would eventually run out of memory and core-dump.

Fixed by explicitly specifying the default values for these two
parameters.

packet, to work around the problem whereby small TX rings get backed
up because we haven't yet poll()ed for TX completions.

packet, to work around the problem whereby small TX rings get backed
up because we haven't yet poll()ed for TX completions.

to construct DHCP packets suitable for Infiniband.