The UEFI specification has an implicit and demonstrably incorrect
requirement (in the Mem_IO() calling convention) that any UNDI network
device has at most one memory BAR and one I/O BAR.
Some UEFI platforms have been observed to report the existence of
non-existent additional I/O BARs, causing iPXE to select the wrong
BAR. This problem does not affect the SnpDxe driver, since that
driver will always choose the lowest numbered existent BAR of each
type.
Adjust iPXE's behaviour to match that of SnpDxe, i.e. to always select
the lowest numbered BAR(s).
Debugged-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Debugged-by: Adklei <adklei@realtek.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smsc75xx] Expose functionality shared with LAN78xx devices
The LAN78xx datapath is essentially identical to that of the SMSC75xx.
Expose the transmit, poll, and bulk IN endpoint operations to allow
for reuse by the LAN78xx driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smscusb] Allow for alternative PHY register layouts
The LAN78xx PHY interrupt source and mask registers do not match those
used by the SMSC75xx and SMSC95xx.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since we don't enable IOMMU at all, we can then simply enable the
IOMMU support by claiming the support of VIRITO_F_IOMMU_PLATFORM.
This fixes booting failure when iommu_platform is set from qemu cli.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smscusb] Abstract out common SMSC USB device functionality
The smsc75xx and smsc95xx drivers include a substantial amount of
identical functionality, varying only in the base address of register
sets. Abstract out this common functionality to allow code to be
shared between the drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support renegotiation with servers supporting RFC5746. This allows
for the use of per-directory client certificates.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Use non-zero language ID to retrieve strings
We currently use a zero language ID to retrieve strings such as the
ECM/NCM MAC address. This works on most hardware devices, but is
known to fail on some software emulated CDC-NCM devices.
Fix by using the first supported language ID, falling back to English
(0x0409) if any error occurs when fetching the list of supported
languages. This matches the behaviour of the Linux kernel.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Provide asn1_built() to construct a cursor from a builder
Our ASN.1 parsing code uses a struct asn1_cursor, while the object
construction code uses a struct asn1_builder. These structures are
identical apart from the const modifier applied to the data pointer in
struct asn1_cursor.
Provide asn1_built() to safely typecast a struct asn1_builder to a
struct asn1_cursor, allowing constructed objects to be passed to
functions expecting a struct asn1_cursor.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For some CPUID leaves (e.g. %eax=0x00000004), the result depends on
the input value of %ecx. Allow this subfunction number to be
specified as a parameter to the cpuid() wrapper.
The subfunction number is exposed via the ${cpuid/...} settings
mechanism using the syntax
${cpuid/<subfunction>.0x40.<register>.<function>}
e.g.
${cpuid/0.0x40.0.0x0000000b}
${cpuid/1.0x40.0.0x0000000b}
to retrieve the CPU topology information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some distributions patch gcc to generate position independent
executables by default. We currently include a workaround to check
for this and to add -fno-PIE -nopie to CFLAGS if required.
Newer patched versions of gcc require -fno-PIE -no-pie instead. Check
for both variants.
Reported-by: Nathan Rennie-Waldock <nathan.renniewaldock@gmail.com>
Originally-fixed-by: Markos Chandras <mchandras@suse.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hdprefix] Avoid attempts to read beyond the end of the disk
When booting from a hard disk image (e.g. bin/ipxe.usb) within an
emulator such as QEMU, the disk may not exist beyond the end of the
image. Limit all reads to the length of the image to avoid spurious
errors when loading the iPXE image.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow values to be read from ACPI tables using the syntax
${acpi/<signature>.<index>.0.<offset>.<length>}
where <signature> is the ACPI table signature as a 32-bit hexadecimal
number (e.g. 0x41504093 for the 'APIC' signature on the MADT), <index>
is the index into the array of tables matching this signature,
<offset> is the byte offset within the table, and <length> is the
field length in bytes.
Numeric values are returned in reverse byte order, since ACPI numeric
values are usually little-endian.
For example:
${acpi/0x41504943.0.0.0.0} - entire MADT table in raw hex
${acpi/0x41504943.0.0.0x0a.6:string} - MADT table OEM ID
${acpi/0x41504943.0.0.0x24.4:uint32} - local APIC address
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tls] Keep cipherstream window open until TLS negotiation is complete
When performing a SAN boot, the plainstream window size will be zero
(since this is the mechanism used internally to indicate that no data
should be fetched via the initial request). This zero value currently
propagates to the advertised TCP window size, which prevents the TLS
negotiation from completing.
Fix by ensuring that the cipherstream window is held open until TLS
negotiation is complete, and only then falling back to passing through
the plainstream window size.
Reported-by: John Wigley <johnwigley#ipxe@acorna.co.uk>
Tested-by: John Wigley <johnwigley#ipxe@acorna.co.uk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Prevent EFI code from being linked in to non-EFI builds
Ensure that efi_systab is an undefined symbol in non-EFI builds. In
particular, this prevents users from incorrectly enabling IMAGE_EFI in
a BIOS build of iPXE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[xen] Provide 18 4kB receive buffers to work around xen-netback bug
The Xen network backend (xen-netback) suffered from a regression
between upstream Linux kernels 3.18 and 4.2 inclusive, which would
cause packet reception to fail unless at least 18 receive buffers were
available. This bug was fixed in kernel commit 1d5d485 ("xen-netback:
require fewer guest Rx slots when not using GSO").
Work around this bug in affected versions of xen-netback by providing
the requisite 18 receive buffers.
Reported-by: Taylor Schneider <tschneider@live.com>
Tested-by: Taylor Schneider <tschneider@live.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[iscsi] Fix iBFT when no explicit initiator name setting exists
Commit 7cfdd76 ("[block] Describe all SAN devices via ACPI tables")
changed the definition of the iSCSI initiator IQN in the iBFT to
represent a common initiator IQN used for all iSCSI sessions, and
attempted to calculate this common initiator IQN by fetching the
common ${initiator-iqn} setting.
This fails when no explicit ${initiator-iqn} has been specified
(i.e. when an initiator IQN has instead been constructed from either
the hostname or system UUID), and results in an empty initiator IQN in
the iBFT.
Fix by using the initiator IQN of an arbitrary iSCSI session
present in the iBFT.
Debugged-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As of kernel 4.11, the LIO target will propose a value for
FirstBurstLength if the initiator did not do so. This is entirely
redundant in our case, since FirstBurstLength is defined by RFC 3720
to be
"Irrelevant when: ( InitialR2T=Yes and ImmediateData=No )"
and we already enforce both InitialR2T=Yes and ImmediateData=No in our
initial proposal. However, LIO (arguably correctly) complains when we
do not respond to its redundant proposal of an already-irrelevant
value.
Fix by always proposing the default value for FirstBurstLength.
Debugged-by: Patrick Seeburger <info@8bit.de>
Tested-by: Patrick Seeburger <info@8bit.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use the PCI bus:dev.fn address in debug messages, falling back to the
EFI handle name only if we do not yet have enough information to
determine the bus:dev.fn address.
Include the vendor and device IDs in debug messages when no suitable
driver is found, to match the diagnostics available in a BIOS
environment.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Cope with Windows Server 2016 enlightenments
An "enlightened" external bootloader (such as Windows Server 2016's
winload.exe) may take ownership of the Hyper-V connection before all
INT 13 operations have been completed. When this happens, all VMBus
devices are implicitly closed and we are left with a non-functional
network connection.
Detect when our Hyper-V connection has been lost (by checking the
SynIC message page MSR). Reclaim ownership of the Hyper-V connection
and reestablish any VMBus devices, without disrupting any existing
iPXE state (such as IPv4 settings attached to the network device).
Windows Server 2016 will not cleanly take ownership of an active
Hyper-V connection. Experimentation shows that we can quiesce by
resetting only the SynIC message page MSR; this results in a
successful SAN boot (on a Windows 2012 R2 physical host). Choose to
quiesce by resetting (almost) all MSRs, in the hope that this will be
more robust against corner cases such as a stray synthetic interrupt
occurring during the handover.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[block] Provide abstraction to allow system to be quiesced
When performing a SAN boot via INT 13, there is no way for the
operating system to indicate that it has finished using the INT 13 SAN
device. We therefore have no opportunity to clean up state before the
loaded operating system's native drivers take over. This can cause
problems when booting Windows, which tends not to be forgiving of
unexpected system state.
Windows will typically write a flag to the SAN device as the last
action before transferring control to the native drivers. We can use
this as a heuristic to bring the system to a quiescent state (without
performing a full shutdown); this provides us an opportunity to
temporarily clean up state that could otherwise prevent a successful
Windows boot.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On most Intel NICs, Auto-Speed Detection Enable (ASDE) can be used to
automatically detect the correct link speed by sampling the link using
the internal PHY. This feature is automatically inhibited when not
appropriate for the physical link (e.g. when using internal SerDes
mode on the 8254x).
On the i350 datasheet ASDE is a reserved bit, but the relevant
auto-speed detection hardware appears still to be present. However,
enabling ASDE on the i350 1000BASE-KX backplane NIC seems to cause an
immediate link failure. It is possible that the auto-speed detection
hardware is still present, is not connected to a physical link, and is
not inhibited from being applied in this mode.
Work around this problem by adding an INTEL_NO_ASDE flag bit
(analogous to INTEL_NO_PHY_RST), and applying this for the i350
backplane NIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Show original CTRL and STATUS values in debugging output
In situations where iPXE fails to reach link-up as expected, it is
useful to know the original values of the CTRL and STATUS registers
prior to our reset attempt.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[block] Allow use of a non-default EFI SAN boot filename
Some older operating systems (e.g. RHEL6) use a non-default filename
on the root disk and rely on setting an EFI variable to point to the
bootloader. This does not work when performing a SAN boot on a
machine where the EFI variable is not present.
Fix by allowing a non-default filename to be specified via the
"sanboot --filename" option or the "san-filename" setting. For
example:
sanboot --filename \efi\redhat\grub.efi \
iscsi:192.168.0.1::::iqn.2010-04.org.ipxe.demo:rhel6
or
option ipxe.san-filename code 188 = string;
option ipxe.san-filename "\\efi\\redhat\\grub.efi";
option root-path "iscsi:192.168.0.1::::iqn.2010-04.org.ipxe.demo:rhel6";
Originally-implemented-by: Vishvananda Ishaya Abrams <vish.ishaya@oracle.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[thunderx] Use ThunderxConfigProtocol to obtain board configuration
Following changes were introduced:
- added GetBgxProp and GetLmacProp methods to ThunderxConfigProtocol
- replaced direct BOARD_CFG access with usage of introduced methods
- removed redundant BOARD_CFG
- changed GUID of ThunderxConfigProtocol, as this is not compatible
with previous version
- changed UINTN* to UINT64* buffer type to fix issue on 32-bit
platforms with MAC address
This change allows us to avoid alignment of BOARD_CFG definitions
every time it changes in UEFI.
Signed-off-by: Konrad Adamczyk <konrad.adamczyk@cavium.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The TEST UNIT READY command is issued automatically when the device is
opened, and is not the result of a command being issued by the caller.
This is required in order that a permanent TEST UNIT READY failure can
be used to identify unusable paths in a multipath SAN device.
Since the TEST UNIT READY command is not part of the caller's command
issuing process, it is not covered by any external retry loops (such
as the main retry loop in sandev_command()).
We must therefore be prepared to retry the TEST UNIT READY command
within the SCSI layer itself. We retry only the TEST UNIT READY
command so as not to multiply the number of potential retries for
normal commands (which are already retried by sandev_command()).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown