EoIB is a fairly simple protocol in which raw Ethernet frames
(excluding the CRC) are encapsulated within Infiniband Unreliable
Datagrams, with a four-byte fixed EoIB header (which conveys no actual
information). The Ethernet broadcast domain is provided by a
multicast group, similar to the IPoIB IPv4 multicast group.
The mapping from Ethernet MAC addresses to Infiniband address vectors
is achieved by snooping incoming traffic and building a peer cache
which can then be used to map a MAC address into a port GID. The
address vector is completed using a path record lookup, as for IPoIB.
Note that this requires every packet to include a GRH.
Add basic support for EoIB devices. This driver is substantially
derived from the IPoIB driver. There is currently no mechanism for
automatically creating EoIB devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smsc95xx] Add driver for SMSC/Microchip LAN95xx USB Ethernet NICs
Tested using QEMU and usbredir to expose the LAN9512 chip present on a
Raspberry Pi.
There is a known issue with the LAN9512: an extra two bytes are
appended to every transmitted packet. These two bytes comprise:
{ 0x00, 0x08 } if packet length == 0 (mod 8)
{ CRC[0], 0x00 } if packet length == 7 (mod 8)
{ CRC[0], CRC[1] } otherwise
The extra bytes are appended whether the Ethernet CRC is generated
manually or added automatically by the hardware. The issue occurs
with the Linux kernel driver as well as the iPXE driver. It appears
to be an undocumented hardware errata.
TCP/IP traffic is not affected, since the IP header length field
causes the extraneous bytes to be discarded by the receiver. However,
protocols that rely on the length of the Ethernet frame (such as FCoE
or iPXE's "lotest" protocol) will be unusable on this hardware.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Expose unused USB devices via EFI_USB_IO_PROTOCOL
Allow the UEFI platform firmware to provide drivers for unrecognised
devices, by exposing our own implementation of EFI_USB_IO_PROTOCOL.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Add a USB host controller driver based on EFI_USB_IO_PROTOCOL
Allow iPXE to coexist with other USB device drivers, by attaching to
the EFI_USB_IO_PROTOCOL instances provided by the UEFI platform
firmware.
The EFI_USB_IO_PROTOCOL is an unsurprisingly badly designed
abstraction of a USB device. The poor design choices intrinsic in the
UEFI specification prevent efficient operation as a network device,
with the result that devices operated using the EFI_USB_IO_PROTOCOL
operate approximately two orders of magnitude slower than devices
operated using our native EHCI or xHCI host controller drivers.
Since the performance is so abysmally slow, and since the underlying
problems are due to fundamental architectural mistakes in the UEFI
specification, support for the EFI_USB_IO_PROTOCOL host controller
driver is left as disabled by default. Users are advised to use the
native iPXE host controller drivers instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Many UEFI NBPs expect to find an EFI_PXE_BASE_CODE_PROTOCOL installed
in addition to the EFI_SIMPLE_NETWORK_PROTOCOL. Most NBPs use the
EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the cached DHCP packets.
This implementation has been tested with grub.efi, shim.efi,
syslinux.efi, and wdsmgfw.efi. Some methods (such as Discover() and
Arp()) are not used by any known NBP and so have not (yet) been
implemented.
Usage notes for the tested bootstraps are:
- grub.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet, and uses no other methods.
- shim.efi uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the cached
DHCP packet and to retrieve the next NBP via the Mtftp() method.
If shim.efi was downloaded via HTTP (or other non-TFTP protocol)
then shim.efi will blindly call Mtftp() with an HTTP URI as the
filename: this allows the next NBP (e.g. grubx64.efi) to also be
transparently retrieved by HTTP.
shim.efi can also use the EFI_SIMPLE_FILE_SYSTEM_PROTOCOL to
retrieve files previously loaded by "imgfetch" or similar commands
in iPXE. The current implementation of shim.efi will use the
EFI_SIMPLE_FILE_SYSTEM_PROTOCOL only if it does not find an
EFI_PXE_BASE_CODE_PROTOCOL; this patch therefore prevents this
usage of our EFI_SIMPLE_FILE_SYSTEM_PROTOCOL. This logic could be
trivially reversed in shim.efi if needed.
- syslinux.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet. Versions 6.03 and earlier have a bug which
may cause syslinux.efi to attach to the wrong NIC if there are
multiple NICs in the system (or if the UEFI firmware supports
IPv6).
- wdsmgfw.efi (ab)uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the
cached DHCP packets, and to send and retrieve UDP packets via the
UdpWrite() and UdpRead() methods. (This was presumably done in
order to minimise the amount of benefit obtainable by switching to
UEFI, by replicating all of the design mistakes present in the
original PXE specification.)
The EFI_DOWNGRADE_UX configuration option remains available for now,
until this implementation has received more widespread testing.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[http] Rewrite HTTP core to support content encodings
Rewrite the HTTP core to allow for the addition of arbitrary content
encoding mechanisms, such as PeerDist and gzip.
The core now exposes http_open() which can be used to create requests
with an explicitly selected HTTP method, an optional requested content
range, and an optional request body. A simple wrapper provides the
preexisting behaviour of creating either a GET request or an
application/x-www-form-urlencoded POST request (if the URI includes
parameters).
The HTTP SAN interface is now implemented using the generic block
device translator. Individual blocks are requested using http_open()
to create a range request.
Server connections are now managed via a connection pool; this allows
for multiple requests to the same server (e.g. for SAN blocks) to be
completely unaware of each other. Repeated HTTPS connections to the
same server can reuse a pooled connection, avoiding the per-connection
overhead of establishing a TLS session (which can take several seconds
if using a client certificate).
Support for HTTP SAN booting and for the Basic and Digest
authentication schemes is now optional and can be controlled via the
SANBOOT_PROTO_HTTP, HTTP_AUTH_BASIC, and HTTP_AUTH_DIGEST build
configuration options in config/general.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
UEFI platforms may provide a watchdog timer, which will reboot the
machine if an operating system takes more than five minutes to load.
This can cause long-lived iPXE downloads (or interactive shell
sessions) to unexpectedly reboot.
Fix by resetting the watchdog timer every ten seconds while the iPXE
main processing loop continues to run.
Reported-by: Bradley B Williams <bradleybwilliams@swbell.net>
Reported-by: John Clark <john.r.clark.3@gmail.com>
Reported-by: wdriever@gmail.com
Reported-by: Charlie Beima <cbeima@indiana.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the AES implementation from AXTLS with a dedicated iPXE
implementation which is slightly smaller and around 1000% faster.
This implementation has been verified using the existing self-tests
based on the NIST AES test vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a generic inject_fault() function that can be used to inject
random faults with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[stp] Add support for detecting Spanning Tree Protocol non-forwarding ports
A fairly common end-user problem is that the default configuration of
a switch may leave the port in a non-forwarding state for a
substantial length of time (tens of seconds) after link up. This can
cause iPXE to time out and give up attempting to boot.
We cannot force the switch to start forwarding packets sooner, since
any attempt to send a Spanning Tree Protocol bridge PDU may cause the
switch to disable our port (if the switch happens to have the Bridge
PDU Guard feature enabled for the port).
For non-ancient versions of the Spanning Tree Protocol, we can detect
whether or not the port is currently forwarding and use this to inform
the network device core that the link is currently blocked.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Add support for mailbox used by virtual functions
Virtual functions use a mailbox to communicate with the physical
function driver: this covers functionality such as obtaining the MAC
address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When USB network card drivers are used, the BIOS' legacy USB
capability is necessarily disabled since there is no way to share the
host controller between the BIOS and iPXE. This currently results in
USB keyboards becoming non-functional in USB-enabled builds of iPXE.
Fix by adding basic support for USB keyboards, enabled by default in
iPXE builds which include USB support.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smsc75xx] Add driver for SMSC/Microchip LAN75xx USB Ethernet NICs
This driver is functional but any downloads via a TCP-based protocol
tend to perform poorly. The 1Gbps Ethernet line rate is substantially
higher than the 480Mbps (in practice around 280Mbps) provided by USB2,
and the device has only 32kB of internal buffer memory. Our 256kB TCP
receive window therefore rapidly overflows the RX FIFO, leading to
multiple dropped packets (usually within the same TCP window) and
hence a low overall throughput.
Reducing the TCP window size so that the RX FIFO does not overflow
greatly increases throughput, but is not a general-purpose solution.
Further investigation is required to determine how other OSes
(e.g. Linux) cope with this scenario. It is possible that
implementing TCP SACK would provide some benefit.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[legal] Relicense files under GPL2_OR_LATER_OR_UBDL
These files cannot be automatically relicensed by util/relicense.pl
since they either contain unusual but trivial contributions (such as
the addition of __nonnull function attributes), or contain lines
dating back to the initial git revision (and so require manual
knowledge of the code's origin).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some UEFI network drivers provide a software UNDI interface which is
exposed via the Network Interface Identifier Protocol (NII), rather
than providing a Simple Network Protocol (SNP).
The UEFI platform firmware will usually include the SnpDxe driver,
which attaches to NII and provides an SNP interface. The SNP
interface is usually provided on the same handle as the underlying NII
device. This causes problems for our EFI driver model: when
efi_driver_connect() detaches existing drivers from the handle it will
cause the SNP interface to be uninstalled, and so our SNP driver will
not be able to attach to the handle. The platform firmware will
eventually reattach the SnpDxe driver and may attach us to the SNP
handle, but we have no way to prevent other drivers from attaching
first.
Fix by providing a driver which can attach directly to the NII
protocol, using the software UNDI interface to drive the network
device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Propagate our modified EFI system table to any images loaded by the
image that we wrap, thereby allowing us to observe boot services calls
made by all subsequent EFI images.
Also show details of intercepted ExitBootServices() calls. When
wrapping is used, exiting boot services will almost certainly fail,
but this at least allows us to see when it happens.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add basic support for Xen PV-HVM domains (detected via the Xen
platform PCI device with IDs 5853:0001), including support for
accessing configuration via XenStore and enumerating devices via
XenBus.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Get the NFS URI manipulation code out of nfs_open.c. The resulting
code is now much more readable.
Signed-off-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[console] Add centralised concept of colours and colour pairs
Add a centralised concept of colours and colour pairs (using the
default colour pairs as configured via config/colour.h). A colour
pair consists of a pair of colour indices.
Add the ability to redefine both a colour pair and an individual
colour index, with minimal overhead if this feature is not required
(e.g. because the relevant shell commands are not present in the
build).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown