Allow drivers to specify a supported PCI class code. To save space in
the final binary, make this an attribute of the driver rather than an
attribute of a PCI device ID list entry.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Require support for VMBus version 3.0 or newer
We require the ability to disconnect from and reconnect to VMBus; if
we don't have this then there is no (viable) way for a loaded
operating system to continue to use any VMBus devices. (There is also
a small but non-zero risk that the host will continue to write to our
interrupt and monitor pages, since the VMBUS_UNLOAD message in earlier
versions is essentially a no-op.)
This requires us to ensure that the host supports protocol version 3.0
(VMBUS_VERSION_WIN8_1). However, we can't actually _use_ protocol
version 3.0, since doing so causes an iSCSI-booted Windows Server 2012
R2 VM to crash due to a NULL pointer dereference in vmbus.sys.
To work around this problem, we first ensure that we can connect using
protocol v3.0, then disconnect and reconnect using the oldest known
protocol.
This deliberately prevents the use of the iPXE native Hyper-V drivers
on older versions of Hyper-V, where we could use our drivers but in so
doing would break the loaded operating system.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[rndis] Ignore start-of-day RNDIS_INDICATE_STATUS_MSG with status 0x40020006
Windows Server 2012 R2 generates an RNDIS_INDICATE_STATUS_MSG with a
status code of 0x4002006. This status code does not appear to be
documented anywhere within the sphere of human knowledge.
Explicitly ignore this status code in order to avoid unnecessarily
cluttering the display when RNDIS debugging is enabled.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Assume that VMBus xfer page ranges correspond to RNDIS messages
The (undocumented) VMBus protocol seems to allow for transfer
page-based packets where the data payload is split into an arbitrary
set of ranges within the transfer page set.
The RNDIS protocol includes a length field within the header of each
message, and it is known from observation that multiple RNDIS messages
can be concatenated into a single VMBus message.
iPXE currently assumes that the transfer page range boundaries are
entirely arbitrary, and uses the RNDIS header length to determine the
RNDIS message boundaries.
Windows Server 2012 R2 generates an RNDIS_INDICATE_STATUS_MSG for an
undocumented and unknown status code (0x40020006) with a malformed
RNDIS header length: the length does not cover the StatusBuffer
portion of the message. This causes iPXE to report a malformed RNDIS
message and to discard any further RNDIS messages within the same
VMBus message.
The Linux Hyper-V driver assumes that the transfer page range
boundaries correspond to RNDIS message boundaries, and so does not
notice the malformed length field in the RNDIS header.
Match the behaviour of the Linux Hyper-V driver: assume that the
transfer page range boundaries correspond to the RNDIS message
boundaries and ignore the RNDIS header length. This avoids triggering
the "malformed packet" error and also avoids unnecessary data copying:
since we now have one I/O buffer per RNDIS message, there is no longer
any need to use iob_split().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Empirical observation suggests that 32 is a sensible size to minimise
the number of deferred packet transmissions without overflowing the
VMBus transmit ring buffer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for elision of transmitted TCP ACKs by handling all received
VMBus messages in each network device poll operation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[rndis] Clear receive filter when closing the device
On Windows Server 2012 R2, closing and reopening the device will
sometimes result in a non-functional RX datapath. The root cause is
unknown. Clearing the receive filter before closing the device seems
to fix the problem.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Tear down NetVSC RX buffer GPADL after closing VMBus device
On Windows Server 2012 R2, the receive buffer teardown completion
message seems to occasionally be deferred until after the VMBus
channel has been closed. This happens even if there are no packets
currently in the receive buffer.
Work around this problem by separating the revocation and teardown of
the receive buffer, and deferring the teardown until after the VMBus
channel has been closed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Hyper-V RNDIS implementation on Windows Server 2012 R2 requires
that we send an explicit RNDIS initialisation message in order to get
a working RX datapath.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[iobuf] Add iob_split() to split an I/O buffer into portions
RNDIS devices may provide multiple packets encapsulated into a single
message. Provide an API to allow the RNDIS driver to split an I/O
buffer into smaller portions.
The current implementation will always copy the underlying data,
rather than splitting the buffer in situ.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Check the integrity of the free memory block list before and after any
modifications to the list. We check that certain invariants are
preserved:
- the list is a well-formed doubly linked list
- all blocks are at least MIN_MEMBLOCK_SIZE
- no block extends beyond the end of our address space
- blocks remain sorted in ascending order of address
- no blocks are adjacent (i.e. any adjacent blocks have been merged)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Fix parsing of OCSP responder ID key hash
We currently compare the entirety of the KeyHash object (including the
ASN.1 tag and length byte) against the raw SHA-1 hash of the
certificate's public key. This causes OCSP validation to fail for any
responses which identify the responder by key hash rather than by
name, and hence prevents the use of X.509 certificates where any
certificate in the chain has an OCSP responder which chooses to
identify itself via its key hash.
Fix by adding the missing asn1_enter() required to enter the ASN.1
octet string containing the key hash.
Also add a corresponding test case including an OCSP response where
the responder is identified by key hash, to ensure that this
functionality cannot be broken in future.
Debugged-by: Brian Rak <brak@gameservers.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Use autoloaded MAC address instead of EEPROM MAC address
The i350 (and possibly other Intel NICs) have a non-trivial
correspondence between the PCI function number and the external
physical port number. For example, the i350 has a "LAN Function Sel"
bit within the EEPROM which can invert the mapping so that function 0
becomes port 3, function 1 becomes port 2, etc.
Unfortunately the MAC addresses within the EEPROM are indexed by
physical port number rather than PCI function number. The end result
is that when anything other than the default mapping is used, iPXE
will use the wrong address as the base MAC address.
Fix by using the autoloaded MAC address if it is valid, and falling
back to reading the MAC address directly from the EEPROM only if no
autoloaded address is available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ping] Allow termination after a specified number of packets
Add the "-c <count>" option to the "ping" command, allowing for
automatic termination after a specified number of packets.
When a number of packets is specified:
- if a serious error (i.e. length mismatch or content mismatch)
occurs, then the ping will be immediately terminated with the relevant
status code;
- if at least one response is received successfully, and all errors
are non-serious (i.e. timeouts or out-of-sequence responses), then
the ping will be terminated after the final response (or timeout)
with a success status;
- if no responses are received successfully, then the ping will be
terminated after the final timeout with ETIMEDOUT.
If no number of packets is specified, then the ping will continue
until manually interrupted.
Originally-implemented-by: Cedric Levasseur <cyr-ius@ipocus.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Include NII driver within "snp" and "snponly" build targets
End users almost certainly don't care whether the underlying interface
is SNP or NII/UNDI. Try to minimise surprise and unnecessary
documentation by including the NII driver whenever the SNP driver is
requested.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE itself exposes a dummy NII protocol with no UNDI. Avoid
potentially dereferencing a NULL pointer by checking for a non-zero
UNDI address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some UEFI network drivers provide a software UNDI interface which is
exposed via the Network Interface Identifier Protocol (NII), rather
than providing a Simple Network Protocol (SNP).
The UEFI platform firmware will usually include the SnpDxe driver,
which attaches to NII and provides an SNP interface. The SNP
interface is usually provided on the same handle as the underlying NII
device. This causes problems for our EFI driver model: when
efi_driver_connect() detaches existing drivers from the handle it will
cause the SNP interface to be uninstalled, and so our SNP driver will
not be able to attach to the handle. The platform firmware will
eventually reattach the SnpDxe driver and may attach us to the SNP
handle, but we have no way to prevent other drivers from attaching
first.
Fix by providing a driver which can attach directly to the NII
protocol, using the software UNDI interface to drive the network
device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Free transmit ring entry before calling netdev_tx_complete()
The snpnet driver uses netdev_tx_defer() and so must ensure that space
in the (single-entry) transmit descriptor ring is freed up before
calling netdev_tx_complete().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Use -malign-double to build 32-bit UEFI binaries
The EDK2 codebase uses -malign-double for 32-bit builds, which causes
64-bit integers to be naturally aligned. This affects the layout of
some structures (including EFI_BLOCK_IO_MEDIA).
This mirrors wimboot commit 7b8f39d ("[build] Fix building of 32-bit
UEFI version").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As of commit 03f0c23 ("[ipoib] Expose Ethernet-compatible eIPoIB
link-layer addresses and headers"), all link layers have used
addresses which fit within the DHCP chaddr field. The dhcp_chaddr()
function was therefore made obsolete by this commit, but was
accidentally left present (though unused) in the source code.
Remove the dhcp_chaddr() function and the only remaining use of it,
unnecessarily introduced in commit 08bcc0f ("[dhcp] Check for matching
chaddr in received DHCP packets").
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcp] Check for matching chaddr in received DHCP packets
On large networks a DHCP XID collision is possible. Fix by explicitly
checking the chaddr in received DHCP packets.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Provide dummy device path in efi_image_probe()
Some UEFI platforms will fail the call to LoadImage() with
EFI_INVALID_PARAMETER if we do not provide a device path (even though
we are providing a non-NULL SourceBuffer).
Fix by providing an empty device path for the call to LoadImage() in
efi_image_probe().
The call to LoadImage() in efi_image_exec() already constructs and
provides a device path (based on the most recently opened SNP device),
and so does not require this fix.
Reported-by: NICOLAS CATTIE <nicolas.cattie@mpsa.com>
Tested-by: NICOLAS CATTIE <nicolas.cattie@mpsa.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the ID for the LM variant and differentiate it from the I217-V.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add utility for constructing EFI fat binaries (dual 32/64-bit
binaries, usable only on Apple EFI systems).
This utility is not part of the standard build process. To use it:
make util/efifatbin bin-i386-efi/ipxe.efi bin-x86_64-efi/ipxe.efi
and then
./util/efifatbin bin-*-efi/ipxe.efi fat-ipxe.efi
Requested-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Tested-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Clean up all binary directories on "make [very]clean"
Allow a straightforward "make clean" or "make veryclean" to apply to
all binary directories (using the shell pattern "bin{,-*}").
Individual binary directories can be cleaned using e.g.
make bin clean
make bin-x86_64-efi clean
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown