[ipv4] Use broadcast link-layer address for all broadcast IPv4 addresses
When transmitting, use the broadcast link-layer address for any
broadcast address (e.g. 192.168.0.255), not just INADDR_BROADCAST
(255.255.255.255).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Explicitly discard any unicast packets for addresses that we do not
control, to avoid unexpected behaviour when operating in promiscuous
mode (which is now the default, thanks to FCoE).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Allow link layer to report broadcast/multicast packets via pull()
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to section 14.23 of RFC2616, an HTTP Host header without
port implies the default port is used. Thus, when fetching from
anywhere but port 80 for HTTP or 443 for HTTPS, the port ought to be
explicitly given in that header. Otherwise, some servers might fail
to associate the request with the correct virtual host or generate
incorrect self-referencing URLs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iSCSI TX process can now be woken up by the TCP socket via
xfer_window_changed(), so it is no longer valid to assume that
iscsi_tx_step() can be called in state ISCSI_TX_IDLE only immediately
after completing a transmission.
Fix by calling iscsi_tx_done() only upon a transition into state
ISCSI_TX_IDLE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Avoid using -ffunction-sections on some older versions of gcc
Some older versions of gcc issue a warning if -ffunction-sections is
used in combination with -g (gcc bug #18553). Inhibit
-ffunction-sections when building with such a version of gcc.
Reported-by: zhengwei <zw111_2001@126.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide support for HTTP range requests, and expose this functionality
via the iPXE block device API. This allows SAN booting from a root
path such as:
sanboot http://boot.ipxe.org/freedos/fdfullcd.iso
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[int13] Provide a permanently closed window via the control interface
Allow objects to support both streaming and block device protocols, by
starting streaming data only when the data transfer window opens.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hw] Eliminate polling while waiting for window to open
Polling for the data-transfer window to become open is wasteful. We
can eliminate the polling loop by using hw_step() as the handler for
an xfer_window_changed() event.
If the window is already open at the time of instantiation, then
xfer_window_changed() may never be called. We can cover this case by
using hw_step() as the step() method of a one-shot process. Since the
signature for an xfer_window_changed() method is identical to the
signature for a process step() method, the same function can be used
for both.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some processes execute only once, and exist solely in order to defer
execution until after the relevant instantiator method has returned.
Such processes do not need to be automatically rescheduled when
executing.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[process] Pass containing object pointer to process step() methods
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[xfer] Send xfer_window_changed() after xfer_vredirect()
Modify the default action for xfer_vredirect() to automatically send
xfer_window_changed() messages to both the new child and the parent
interfaces. This will allow the elimination of processes that simply
poll on xfer_window() to determine when a redirection has completed
successfully.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ftp_data_deliver() does nothing except pass through the received data
to the xfer interface, and so can be eliminated by using a
pass-through interface.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[prefix] Cope with BOOT_IMAGE= anywhere within command line
Some bootloaders seem to add "BOOT_IMAGE=..." at the end of the
command line; some at the start. Cope with either variation.
Reported-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At the time of attempting ARP resolution, we already know the
transmitting network device. We can therefore record ARP errors using
netdev_tx_err() so that they show up in the output of "ifstat".
Inspired-by: Dominik Russenberger <dominik.russenberger@terreactive.ch>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Allow non-completion TX errors to be recorded
Allow TX errors to be recorded against a network device even when the
packet didn't make it as far as netdev_tx().
Inspired-by: Dominik Russenberger <dominik.russenberger@terreactive.ch>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Force PnP header to a 16-byte boundary for IBM BIOSes
IBM BIOSes ignore the PnP header offset stored at address 0x1a and
instead scan for the $PnP signature on a 16-byte boundary. (This
alignment is not mandated by the PnP specification.)
Force PnP header to a 16-byte boundary to work around these BIOSes.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Do not fall back to hooking INT19 by default
Several BIOSes (including most IBM BIOSes and many virtual machine
BIOSes) do not provide detectable PnP support, but will use the BEV
entry point for a PnP option ROM. On these semi-PnP BIOSes, iPXE will
respond to the absence of detectable PnP support by hooking INT19,
which disrupts the boot order.
BIOSes that genuinely require hooking INT19 seem to be very rare
nowadays. It may therefore be preferable to assume that the absence
of detectable PnP support indicates a semi-PnP BIOS rather than a
non-PnP BIOS.
Change the default behaviour so that INT19 will never be hooked unless
the compile-time option NONPNP_HOOK_INT19 is enabled. Leave the
redundant PnP detection routine in-place to allow for debugging via
the ROM banner line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Remove special treatment for IBM BIOSes
Revert commit 38cd351 ("[romprefix] Attempt to gracefully handle
semi-PnP IBM BIOSes"), since the test for the "IBM " signature in %edi
is not sufficient to identify an IBM BIOS.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv4] Include network device metadata in packet traces
(Ab)use the "ident" field in transmitted IPv4 packets to convey
metadata about the network device. In particular:
bits 0-3 represent the low bits of the "RX" good packet counter
bits 4-7 represent the low bits of the "RXE" bad packet counter
bits 8-15 represent the transmitted packet sequence number
This allows some relevant information about the internal state of the
network device to be read out from a packet trace from a non-debug
build of iPXE. In particular, it allows a packet trace containing
packets transmitted by iPXE to indicate whether or not any packets
have been received by iPXE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Booting from an HTTP SAN will require HTTP range requests, which are
defined only in HTTP/1.1 and above. HTTP/1.1 mandates support for
"Transfer-Encoding: chunked", so we must support it.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hermon] Remove temporary workaround for missing BOFM mport support
This reverts commit 15c1200 ("[hermon] Work around missing mport
support in current BOFM implementations").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[bofm] Report {slot,port} to {bus:dev.fn,mport} mapping on newer BOFM builds
Newer BOFM builds provide support for mapping multiple physical ports
to a single PCI bus:dev.fn via PCI VPD descriptions. These builds
will also leave the {slot,port} field intact, and will populate the
mport field with a meaningful value.
Older BOFM builds will zero out the {slot,port} field. A zero value
in this field may indicate either a genuine zero value (i.e. slot 0
first port) or an older build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Attempt to gracefully handle semi-PnP IBM BIOSes
Some IBM BIOSes provide partial support for PnP: they will use the BEV
entry point but will not advertise PnP support. This causes iPXE to
hook INT 19, which disrupts the boot process.
Attempt to improve this situation by detecting an IBM BIOS and
treating it as a PnP BIOS despite the absence of a PnP signature.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown