A window size of 256kB should be sufficient to allow for
full-bandwidth transfers over a Gigabit LAN, and for acceptable
transfer speeds over other typical links.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Discarding the active ARP cache entry in the middle of a download will
substantially disrupt the TCP stream. Try to minimise any such
disruption by treating ARP cache entries as expensive, and discarding
them only when nothing else is available to discard.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[iobuf] Relax alignment requirement for small I/O buffers
iPXE currently aligns all I/O buffers on a 2kB boundary. This is
overkill for transmitted packets, which are typically much smaller
than 2kB.
Align I/O buffers on their own size. This reduces the alignment
requirement for small buffers, while preserving the guarantee that I/O
buffers will never cross boundaries that might cause problems for some
DMA engines.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tls] Request a maximum fragment length of 2048 bytes
The default maximum plaintext fragment length for TLS is 16kB, which
is a substantial amount of memory for iPXE to have to allocate for a
temporary decryption buffer.
Reduce the memory footprint of TLS connections by requesting a maximum
fragment length of 2kB.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The maximum unscaled TCP window (64kB) implies a maximum bandwidth of
around 300kB/s on a WAN link with an RTT of 200ms. Add support for
the TCP window scaling option to remove this upper limit.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcpip] Allow for architecture-specific TCP/IP checksum routines
Calculating the TCP/IP checksum on received packets accounts for a
substantial fraction of the response latency.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Allow an error margin on X.509 certificate validity periods
iPXE has no concept of the local time zone, mainly because there is no
viable way to obtain time zone information in the absence of local
state. This causes potential problems with newly-issued certificates
and certificates that are about to expire.
Avoid such problems by allowing an error margin of around 12 hours on
certificate validity periods, similar to the error margin already
allowed for OCSP response timestamps.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcp] Request broadcast responses when we already have an IPv4 address
FCoE requires the use of multiple local unicast link-layer addresses.
To avoid the complexity of managing multiple addresses, iPXE operates
in promiscuous mode. As a consequence, any unicast packets with
non-matching IPv4 addresses are rejected at the IPv4 layer (rather
than at the link layer).
This can cause problems when issuing a second DHCP request: if the
address chosen by the DHCP server does not match the existing address,
then the DHCP response will itself be rejected.
Fix by requesting a broadcast response from the DHCP server if the
network interface already has any IPv4 addresses.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE is fundamentally asynchronous in operation: some operations
continue in the background even after the foreground has continued to
a new task. For example, the closing FIN/ACK exchanges of a TCP
connection will take place in the background after an HTTP download
has completed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for constructing OCSP queries and parsing OCSP responses.
(There is no support yet for actually issuing an OCSP query via an
HTTP POST.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Automatically attempt to download any required cross-signing
certificates from http://ca.ipxe.org/auto, in order to enable the use
of standard SSL certificates issued by public CAs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
To allow for automatic download of cross-signing certificates and for
OCSP, the validation of certificates must be an asynchronous process.
Create a stub validator which uses a job-control interface to report
the result of certificate validation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
CMS includes an unordered certificate set, from which certificates
must be extracted in order by matching up issuers with subjects. We
will use the same functionality as part of the automatic download of
cross-signing certificates. Generalise cms_find_subject() to
x509_find_subject(), and create x509_auto_append().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Allow certificate chains to be long-lived data structures
At present, certificate chain validation is treated as an
instantaneous process that can be carried out using only data that is
already in memory. This model does not allow for validation to
include non-instantaneous steps, such as downloading a cross-signing
certificate, or determining certificate revocation status via OCSP.
Redesign the internal representation of certificate chains to allow
chains to outlive the scope of the original source of certificates
(such as a TLS Certificate record).
Allow for certificates to be cached, so that each certificate needs to
be validated only once.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Allow trusted root certificate to be changed without a rebuild
Changing the trusted root certificate currently requires a rebuild of
the iPXE binary, which may be inconvenient or impractical.
Allow the list of trusted root certificate fingerprints to be
overridden using the "trust" setting, but only at the point of iPXE
initialisation. This prevents untrusted sources of settings
(e.g. DHCP) from subverting the chain of trust, while allowing
trustworthy sources to change the trusted root certificate without
requiring a rebuild.
The basic idea is that if you are able to manipulate a trustworthy
source of settings (e.g. VMware GuestInfo or non-volatile stored
options), then you would be able to replace the iPXE binary anyway,
and so no security is lost by allowing such sources to override the
list of trusted root certificates.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Solaris assumes that there is enough space above the Multiboot modules
to use as a decompression and scratch area. This assumption is
invalid when using iPXE, which places the Multiboot modules near the
top of (32-bit) memory.
Fix by copying the modules to an area of memory immediately following
the loaded kernel.
Debugged-by: Michael Brown <mcb30@ipxe.org>
Debugged-by: Scott McWhirter <scottm@joyent.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE provides no support for manually configuring the link speed.
Provide a generic routine which should be able to reset any MII/GMII
PHY and enable autonegotiation.
Prototyped-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Split fetching and storing out of setting type handlers
Refactor setting type handlers to parse and format values, rather than
storing and fetching formatted values.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown