USB Communications Device Class devices may use a union functional
descriptor to group several interfaces into a function.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Iterate over a USB device's available configurations until we find one
for which we have working drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some protocols (such as ARP) may modify the received packet and re-use
the same I/O buffer for transmission of a reply. To allow this,
reserve sufficient headroom at the start of each received packet
buffer for our transmit datapath headers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some devices have a very small number of internal buffers, and rely on
being able to pack multiple packets into each buffer. Using 2048-byte
buffers on such devices produces throughput of around 100Mbps. Using
a small number of much larger buffers (e.g. 32kB) increases the
throughput to around 780Mbps. (The full 1Gbps is not reached because
the high RTT induced by the use of multi-packet buffers causes us to
saturate our 256kB TCP window.)
Since allocation of large buffers is very likely to fail, allocate the
buffer set only once when the device is opened and recycle buffers
immediately after use. Received data is now always copied to
per-packet buffers.
If allocation of large buffers fails, fall back to allocating a larger
number of smaller buffers. This will give reduced performance, but
the device will at least still be functional.
Share code between the interrupt and bulk IN endpoint handlers, since
the buffer handling is now very similar.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow drivers to specify a supported PCI class code. To save space in
the final binary, make this an attribute of the driver rather than an
attribute of a PCI device ID list entry.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Assume that VMBus xfer page ranges correspond to RNDIS messages
The (undocumented) VMBus protocol seems to allow for transfer
page-based packets where the data payload is split into an arbitrary
set of ranges within the transfer page set.
The RNDIS protocol includes a length field within the header of each
message, and it is known from observation that multiple RNDIS messages
can be concatenated into a single VMBus message.
iPXE currently assumes that the transfer page range boundaries are
entirely arbitrary, and uses the RNDIS header length to determine the
RNDIS message boundaries.
Windows Server 2012 R2 generates an RNDIS_INDICATE_STATUS_MSG for an
undocumented and unknown status code (0x40020006) with a malformed
RNDIS header length: the length does not cover the StatusBuffer
portion of the message. This causes iPXE to report a malformed RNDIS
message and to discard any further RNDIS messages within the same
VMBus message.
The Linux Hyper-V driver assumes that the transfer page range
boundaries correspond to RNDIS message boundaries, and so does not
notice the malformed length field in the RNDIS header.
Match the behaviour of the Linux Hyper-V driver: assume that the
transfer page range boundaries correspond to the RNDIS message
boundaries and ignore the RNDIS header length. This avoids triggering
the "malformed packet" error and also avoids unnecessary data copying:
since we now have one I/O buffer per RNDIS message, there is no longer
any need to use iob_split().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Empirical observation suggests that 32 is a sensible size to minimise
the number of deferred packet transmissions without overflowing the
VMBus transmit ring buffer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for elision of transmitted TCP ACKs by handling all received
VMBus messages in each network device poll operation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Tear down NetVSC RX buffer GPADL after closing VMBus device
On Windows Server 2012 R2, the receive buffer teardown completion
message seems to occasionally be deferred until after the VMBus
channel has been closed. This happens even if there are no packets
currently in the receive buffer.
Work around this problem by separating the revocation and teardown of
the receive buffer, and deferring the teardown until after the VMBus
channel has been closed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Use autoloaded MAC address instead of EEPROM MAC address
The i350 (and possibly other Intel NICs) have a non-trivial
correspondence between the PCI function number and the external
physical port number. For example, the i350 has a "LAN Function Sel"
bit within the EEPROM which can invert the mapping so that function 0
becomes port 3, function 1 becomes port 2, etc.
Unfortunately the MAC addresses within the EEPROM are indexed by
physical port number rather than PCI function number. The end result
is that when anything other than the default mapping is used, iPXE
will use the wrong address as the base MAC address.
Fix by using the autoloaded MAC address if it is valid, and falling
back to reading the MAC address directly from the EEPROM only if no
autoloaded address is available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Include NII driver within "snp" and "snponly" build targets
End users almost certainly don't care whether the underlying interface
is SNP or NII/UNDI. Try to minimise surprise and unnecessary
documentation by including the NII driver whenever the SNP driver is
requested.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE itself exposes a dummy NII protocol with no UNDI. Avoid
potentially dereferencing a NULL pointer by checking for a non-zero
UNDI address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some UEFI network drivers provide a software UNDI interface which is
exposed via the Network Interface Identifier Protocol (NII), rather
than providing a Simple Network Protocol (SNP).
The UEFI platform firmware will usually include the SnpDxe driver,
which attaches to NII and provides an SNP interface. The SNP
interface is usually provided on the same handle as the underlying NII
device. This causes problems for our EFI driver model: when
efi_driver_connect() detaches existing drivers from the handle it will
cause the SNP interface to be uninstalled, and so our SNP driver will
not be able to attach to the handle. The platform firmware will
eventually reattach the SnpDxe driver and may attach us to the SNP
handle, but we have no way to prevent other drivers from attaching
first.
Fix by providing a driver which can attach directly to the NII
protocol, using the software UNDI interface to drive the network
device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Free transmit ring entry before calling netdev_tx_complete()
The snpnet driver uses netdev_tx_defer() and so must ensure that space
in the (single-entry) transmit descriptor ring is freed up before
calling netdev_tx_complete().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the ID for the LM variant and differentiate it from the I217-V.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently require information about the underlying PCI device to
populate the snpnet device's name and description. If the underlying
device is not a PCI device, this will fail and prevent the device from
being registered.
Fix by falling back to populating the device description with
information based on the EFI handle, if no PCI device information is
available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Use the SNP protocol instance to match the SNP chainloading device
Some systems will install a child of the SNP device and use this as
our loaded image's device handle, duplicating the installation of the
underlying SNP protocol onto the child device handle. On such
systems, we want to end up driving the parent device (and
disconnecting any other drivers, such as MNP, which may be attached to
the parent device).
Fix by recording the SNP protocol instance at initialisation time, and
using this to match against device handles (rather than simply
comparing the handles themselves).
Reported-by: Jarrod Johnson <jarrod.b.johnson@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Apply PBS/PBA errata workaround only to ICH8 PCI device IDs
ICH8 devices have an errata which requires us to reconfigure the
packet buffer size (PBS) register, and correspondingly adjust the
packet buffer allocation (PBA) register. The "Intel I/O Controller
Hub ICH8/9/10 and 82566/82567/82562V Software Developer's Manual"
notes for the PBS register that:
10.4.20 Packet Buffer Size - PBS (01008h; R/W)
Note: The default setting of this register is 20 KB and is
incorrect. This register must be programmed to 16 KB.
Initial value: 0014h
0018h (ICH9/ICH10)
It is unclear from this comment precisely which devices require the
workaround to be applied. We currently attempt to err on the side of
caution: if we detect an initial value of either 0x14 or 0x18 then the
workaround will be applied. If the workaround is applied
unnecessarily, then the effect should be just that we use less than
the full amount of the available packet buffer memory.
Unfortunately this approach does not play nicely with other device
drivers. For example, the Linux e1000e driver will rewrite PBA while
assuming that PBS still contains the default value, which can result
in inconsistent values between the two registers, and a corresponding
inability to transmit or receive packets. Even more unfortunately,
the contents of PBS and PBA are not reset by anything less than a
power cycle, meaning that this error condition will survive a hardware
reset.
The Linux driver (written and maintained by Intel) applies the PBS/PBA
errata workaround only for devices in the ICH8 family, identified via
the PCI device ID. Adopt a similar approach, using the PCI_ROM()
driver data field to indicate when the workaround is required.
Reported-by: Donald Bindner <dbindner@truman.edu>
Debugged-by: Donald Bindner <dbindner@truman.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Under some circumstances (e.g. if iPXE itself is booted via iSCSI, or
after an unclean reboot), the backend may not be in the expected
InitWait state when iPXE starts up.
There is no generic reset mechanism for Xenbus devices. Recent
versions of xen-netback will gracefully perform all of the required
steps if the frontend sets its state to Initialising. Older versions
(such as that found in XenServer 6.2.0) require the frontend to
transition through Closed before reaching Initialising.
Add a reset mechanism for netfront devices which does the following:
- read current backend state
- if backend state is anything other than InitWait, then set the
frontend state to Closed and wait for the backend to also reach
Closed
- set the frontend state to Initialising and wait for the backend to
reach InitWait.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Using version 1 grant tables limits guests to using 16TB of grantable
RAM, and prevents the use of subpage grants. Some versions of the Xen
hypervisor refuse to allow the grant table version to be set after the
first grant references have been created, so the loaded operating
system may be stuck with whatever choice we make here. We therefore
currently use version 2 grant tables, since they give the most
flexibility to the loaded OS.
Current versions (7.2.0) of the Windows PV drivers have no support for
version 2 grant tables, and will merrily create version 1 entries in
what the hypervisor believes to be a version 2 table. This causes
some confusion.
Avoid this problem by attempting to use version 1 tables, since
otherwise we may render Windows unable to boot.
Play nicely with other potential bootloaders by accepting either
version 1 or version 2 grant tables (if we are unable to set our
requested version).
Note that the use of version 1 tables on a 64-bit system introduces a
possible failure path in which a frame number cannot fit into the
32-bit field within the v1 structure. This in turn introduces
additional failure paths into netfront_transmit() and
netfront_refill_rx().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The behavior observed in the Apple EFI (1.10) RecieveFilters() call
is:
- failure if any of the PROMISCUOUS or MULTICAST filters are
included
- success if only UNICAST is included, however the result is
UNICAST|BROADCAST
- success if only UNICAST and BROADCAST are included
- if UNICAST, or UNICAST|BROADCAST are used, but the previous call
tried (and failed) to set UNICAST|BROADCAST|MULTICAST, then the
result is UNICAST|BROADCAST|MULTICAST
Work around this apparently broken SNP implementation by trying
RecieveFilterMask, then falling back to UNICAST|BROADCAST|MULTICAST,
then UNICAST|BROADCAST, and finally UNICAST.
Modified-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Curtis Larsen <larsen@dixie.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Open device path protocol only at point of use
Some EFI 1.10 systems (observed on an Apple iMac) do not allow us to
open the device path protocol with an attribute of
EFI_OPEN_PROTOCOL_BY_DRIVER and so we cannot maintain a safe,
long-lived pointer to the device path. Work around this by instead
opening the device path protocol with an attribute of
EFI_OPEN_PROTOCOL_GET_PROTOCOL whenever we need to use it.
Debugged-by: Curtis Larsen <larsen@dixie.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Reset multicast filter list when setting SNP receive filters
According to the UEFI specification, the MCastFilter parameter (which
we currently pass as NULL, along with a zero MCastFilterCnt) is
optional only if ResetMCastFilter is true.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Dump existing openers when we are unable to open a protocol
Dump the existing openers of a protocol whenever we are unable to open
a protocol using attributes of BY_DEVICE, EXCLUSIVE, or
BY_CHILD_CONTROLLER.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Use efi_handle_name() instead of efi_devpath_text() where applicable
Using efi_devpath_text() is marginally more efficient if we already
have the device path protocol available, but the mild increase in
efficiency is not worth compromising the clarity of the pattern:
DBGC ( device, "THING %p %s ...", device, efi_handle_name ( device ) );
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Rewrite the SNP NIC driver to use non-blocking and deferrable
transmissions, to provide link status detection, to provide
information about the underlying (PCI) hardware device, and to avoid
unnecessary I/O buffer allocations during receive polling.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown