ns8390.c can produce four different drivers (one PCI, three ISA.) The
ISA driver requires setting a few macros; do that by setting defines
in stub files instead of using src/Config.
Currently, all the ISA drivers are broken (they were not enabled by
default), so #if 0 them out.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When the 16-bit segment registers are accessed using 32-bit instructions
the high order bytes are undefined on older CPUs. We now explicitly
zero the high order bytes when snapshotting the CPU state. This ensures
that the GDB stub reports consistent values for the segment registers.
This commit implements GDB over UDP. Using UDP is more complex than
serial and has required some restructuring.
The GDB stub is now built using one or both of GDBSERIAL and GDBUDP
config.h options.
To enter the debugger, execute the gPXE shell command:
gdbstub <transport> [<options>...]
Where <transport> is "serial" or "udp". For "udp", the name of a
configured network device is required:
gdbstub udp net0
The GDB stub listens on UDP port 43770 by default.
Commit fd0aef9 introduced a typo that caused PMM detection to start at
paragraph 0xe00 rather than 0xe000. (Detection would still work, since it
would scan until it ran out of base memory, but it would end up scanning
an unnecessarily large portion of base memory.)
Spotted by Sebastian Herbszt <herbszt@gmx.de>.
[a20] Send a null command to the KBC after changing A20
Send a null command, specifically "pulse outputs" with no outputs
selected, to the KBC after changing A20. This was apparently done by DOS,
presumably as a synchronization hack, and the authors of the UHCI spec
thought it was inherent. Therefore, there are systems out there (e.g. HP
DL360 G5) which will stop responsing to "legacy USB" unless they see the
null command, 0xFF, written to port 0x64 at the end of the A20 toggling
sequence.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
[legacy] Align legacy drivers' __shared data to the maximum possible
Some drivers that still use the legacy-driver wrapper (tg3 in particular)
apparently do not specify their alignment constraints properly. This
hack forces any __shared data to be maximally aligned.
Note that this provides only 16-byte alignment; it is not possible to
request alignment to any greater than 16 bytes using
__attribute__((aligned)), since the relocation code will preserve only 16
byte alignment (and operation under -DKEEP_IT_REAL cannot preserve more
that 16 byte alignment).
Idea proposed by Tim Hockin <thockin@google.com>
[prefix] When we have to hook INT 19, chain to original handler if possible
When the BIOS doesn't support BBS, hooking INT 19 is the only way to add
ourselves as a boot device. If we have to do this, we should at least
try to chain to the original INT 19 vector if our boot fails.
Idea suggested by Andrew Schran <aschran@google.com>
[bzimage] Support kernel command lines of greater than 256 characters
2.6.22+ kernels have an extra field in the bzimage_header structure to
indicate the maximum permitted command-line length. Use this if it is
available.
A bug in read_smbios_string() was causing the starting offset of the
SMBIOS structure to be added twice, resulting in completely the wrong
strings being returned.
Bug identified by Martin Herweg <m.herweg@gmx.de>
[slam] Add support for SLAM window lengths of greater than one packet
Add the definition of SLAM_MAX_BLOCKS_PER_NACK, which is roughly
equivalent to a TCP window size; it represents the maximum number of
packets that will be requested in a single NACK.
Note that, to keep the code size down, we still limit ourselves to
requesting only a single range per NACK; if the missing-block list is
discontiguous then we may request fewer than SLAM_MAX_BLOCKS_PER_NACK
blocks.
[console] Call cpu_nap() only if there is no input waiting
Avoid calling cpu_nap() until after we have determined that there is
no input ready to read. This avoids delaying for one timer interrupt
(~50ms) in the case of
if ( iskey() )
char = getkey()
which happens to be present in monojob.c, which is where we spend most
of our time looping (e.g. during any download).
This should eliminate the irritating tendency of gPXE to lose
keypresses.
Discovered on a Dell system where the serial port seems to send in a
constant stream of 0xff characters; this wouldn't be a problem in
itself except that each one triggers the 50ms delay (as mentioned
above), which really kills performance.
On any fast network, or with any driver that may drop packets
(e.g. Infiniband, which has very small RX rings), the traditional
usage of the SLAM protocol will result in enormous numbers of packet
drops and a consequent large number of retransmissions.
By adapting the client behaviour, we can force the server to act more
like a multicast TFTP server, with flow control provided by a single
master client.
This behaviour should interoperate with any traditional SLAM client
(e.g. Etherboot 5.4) on the network. The SLAM protocol isn't actually
documented anywhere, so it's hard to define either behaviour as
compliant or otherwise.
[dhcp] Do not transition to DHCPREQUEST without a valid DHCPOFFER
A missing test for dhcp->dhcpoffer in dhcp_timer_expired() was causing
the client to transition to DHCPREQUEST after timing out on waiting
for ProxyDHCP even if no DHCPOFFERs had been received.
[slam] Request all remaining blocks if we run out of space for the blocklist
In a SLAM NACK packet, if we run out of space to represent the
missing-block list, then indicate all remaining blocks as missing.
This avoids the need to wait for the one-second timeout before
receiving the blocks that otherwise wouldn't have been requested due
to running out of space.
[slam] Speed up NACK transmission by restricting the block-list length
Shorter NACK packets take less time to construct and spew out less
debug output, and there's a limit to how useful it is to send a
complete missing-block list anyway; if the loss rate is high then
we're going to have to retransmit an updated missing-block list
anyway.
Also add pretty debugging output to show the list of requested blocks.
[undi] Ask for promiscuous packet reception when using UNDI driver
We never set up specific multicast filters; native drivers will ask
the card to receive all multicast packets. The only way to achieve
this via the UNDI API is to enable promiscuous mode.
[udp] Verify local socket address (if specified) for UDP sockets
UDP sockets can be used for multicast, at which point it becomes
plausible that we could receive packets that aren't destined for us
but that still match on a port number.
[ELF] Add ability to boot ELF images generated by wraplinux and mkelfImage
Delete ELF as a generic image type. The method for invoking an
ELF-based image (as well as any tables that must be set up to allow it
to boot) will always depend on the specific architecture. core/elf.c
now only provides the elf_load() function, to avoid duplicating
functionality between ELF-based image types.
Add arch/i386/image/elfboot.c, to handle the generic case of 32-bit
x86 ELF images. We don't currently set up any multiboot tables, ELF
notes, etc. This seems to be sufficient for loading kernels generated
using both wraplinux and coreboot's mkelfImage.
Note that while Etherboot 5.4 allowed ELF images to return, we don't.
There is no callback mechanism for the loaded image to shut down gPXE,
which means that we have to shut down before invoking the image. This
means that we lose device state, protection against being trampled on,
etc. It is not safe to continue afterwards.
[Makefile] Use .PRECIOUS instead of .SECONDARY for bin/%.tmp targets
Revert "Use .SECONDARY instead of .PRECIOUS for bin/%.tmp targets."
This reverts commit de29e5a39c.
.SECONDARY doesn't seem to work properly with the target patterns of
implicit rules. In particular, a "make clean ; make bin/rtl8139.dsk"
will correctly leave the bin/rtl8139.dsk.tmp file present when .PRECIOUS
is used, but not when .SECONDARY is used.
This is slightly irritating since we don't want the
"do-not-delete-if-interrupted" semantics of .PRECIOUS, but it seems to be
the best compromise.
During development it is often handy to change the config.h options from
their defaults, for example to enable debugging features.
To prevent accidental commits of debugging config.h changes, mdc
suggested having a config-local.h that is excluded from source control.
This file acts as a temporary config.h and can override any of the
defaults.
This commit is an attempt to implement the config-local.h feature.
The config.h file now has the following as its last line:
/* @TRYSOURCE config-local.h */
The @TRYSOURCE directive causes config-local.h to be included at that
point in the file. If config-local.h does not exist, no error will be
printed and parsing will continue as normal. Therefore, mkconfig.pl is
"trying" to "source" config-local.h.
The GDBSYM config.h option was an attempt at QEMU GDB debugging. I have
removed the code since it is unused and may confuse people wanting to
use the GDB stub.
H. Peter Anvin