The "progress" macro can be used only from within the .prefix section.
At the point of calling relocate(), we are running in .text16 and so
the near call to print_message() will end up calling a random function
somewhere in .text16.
Interestingly, this problem has remained unnoticed for some time. It
is rare to build with DEBUG=libprefix. In the few cases that it has
been used during development, the randomly selected function in
.text16 seems to have been a harmless no-op with no visible
side-effects (beyond the unnoticed failure to print the "relocate"
progress message).
Fix by removing the futile attempt to print a progress message before
calling relocate().
Reported-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Avoid using PMM-allocated memory in UNDI loader entry point
The UNDI loader entry point is very likely to be called after POST,
when there is a high chance that the PMM-allocated image source area
and decompression area have been reused by something else.
In particular, using an iPXE .iso to test a separate iPXE ROM's UNDI
loader entry point in a qemu VM is likely to crash. SeaBIOS allocates
PMM blocks from close to the top of memory and so these blocks have a
high chance of colliding with the runtime addresses subsequently
chosen by the non-ROM iPXE by scanning the INT 15,e820 memory map.
The standard romprefix.S has no choice about relying on the
PMM-allocated image source area, since it has no other way to retrieve
its compressed payload.
In mromprefix.S, the image source area functions only as an optional
buffer used to avoid repeated reads from the (potentially slow)
expansion ROM BAR by the decompression code. We can therefore always
set %esi=0 when calling install_prealloc from the UNDI loader entry
point, and simply fall back to reading directly from the expansion ROM
BAR.
We can always set %edi=0 when calling install_prealloc from the UNDI
loader entry point. This will behave as though the decompression area
PMM allocation failed, and will therefore use INT 15,88 to find a
temporary decompression area somewhere close to 64MB. This is by no
means guaranteed to be safe from collisions, but it's probably safer
on balance than the PMM-allocated address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use the standard "pushl $function ; pushw %cs ; call prot_call"
sequence everywhere that prot_call() is used.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Move most arch/i386 files to arch/x86, and adjust the contents of the
Makefiles and the include/bits/*.h headers to reflect the new
locations.
This patch makes no substantive code changes, as can be seen using a
rename-aware diff (e.g. "git show -M5").
This patch does not make the pcbios platform functional for x86_64; it
merely allows it to compile without errors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
UEFI platforms may provide a watchdog timer, which will reboot the
machine if an operating system takes more than five minutes to load.
This can cause long-lived iPXE downloads (or interactive shell
sessions) to unexpectedly reboot.
Fix by resetting the watchdog timer every ten seconds while the iPXE
main processing loop continues to run.
Reported-by: Bradley B Williams <bradleybwilliams@swbell.net>
Reported-by: John Clark <john.r.clark.3@gmail.com>
Reported-by: wdriever@gmail.com
Reported-by: Charlie Beima <cbeima@indiana.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Ensure drivers are disconnected when ExitBootServices() is called
We hook the UEFI ExitBootServices() event and use it to trigger a call
to shutdown_boot(). This does not automatically cause drivers to be
disconnected from their devices, since device enumeration is now
handled by the UEFI core rather than by iPXE. (Under the old and
dubiously compatible device model, iPXE used to perform its own device
enumeration and so the call to shutdown_boot() would indeed have
caused drivers to be disconnected.)
Fix by replicating parts of the dummy "EFI root device" from
efiprefix.c to efidrvprefix.c, so that the call to shutdown_boot()
will call efi_driver_disconnect_all().
Originally-fixed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Default to releasing network devices for use via SNP
We currently treat network devices as available for use via the SNP
API only if RX queue processing has been frozen. (This is similar in
spirit to the way that RX queue processing is frozen for the network
device currently exposed via the PXE API.)
The default state of a freshly created network device is for the RX
queue to not be frozen, and thus to be unavailable for use via SNP.
This causes problems when devices are added through code paths other
than _efidrv_start() (which explicitly releases devices for use via
SNP).
We don't actually need to freeze RX queue processing, since calls via
the SNP API will always use netdev_poll() rather than net_poll(), and
so will never trigger the RX queue processing code path anyway.
We can therefore simplify the code to use a single global flag to
indicate whether network devices are claimed for use by iPXE or
available for use via SNP. Using a global flag allows the default
state for dynamically created network devices to behave sensibly.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a single instance of EFI_DRIVER_BINDING_PROTOCOL (attached to
our image handle); this matches the expectations scattered throughout
the EFI specification.
Open the underlying hardware device using EFI_OPEN_PROTOCOL_BY_DRIVER
and EFI_OPEN_PROTOCOL_EXCLUSIVE, to prevent other drivers from
attaching to the same device.
Do not automatically connect to devices when being loaded as a driver;
leave this task to the platform firmware (or to the user, if loading
directly from the EFI shell).
When running as an application, forcibly disconnect any existing
drivers from devices that we want to control, and reconnect them on
exit.
Provide a meaningful driver version number (based on the build
timestamp), to allow platform firmware to automatically load newer
versions of iPXE drivers if multiple drivers are present.
Include device paths within debug messages where possible, to aid in
debugging.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Disable SNP devices when running iPXE as the application
Some UEFI builds will set up a timer to continuously poll any SNP
devices. This can drain packets from the network device's receive
queue before iPXE gets a chance to process them.
Use netdev_rx_[un]freeze() to explicitly indicate when we expect our
network devices to be driven via the external SNP API (as we do with
the UNDI API on the standard BIOS build), and disable the SNP API
except when receive queue processing is frozen.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFIRC() uses PLATFORM_TO_ERRNO(), which evaluates its argument twice
(and can't trivially use a braced-group expression or an inline
function to avoid this, since it gets used outside of function
context).
The expression "EFIRC(main())" will therefore end up calling main()
twice, which is not the intended behaviour. Every other instance of
EFIRC() is of the simple form "EFIRC(rc)", so fix by converting this
instance to match.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Exploit the redefinition of iPXE error codes to include a "platform
error code" to allow for meaningful conversion of EFI_STATUS values to
iPXE errors and vice versa.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFI performs its own PCI bus enumeration. Respect this, and start
controlling devices only when instructed to do so by EFI.
As a side benefit, we should now correctly create multiple SNP
instances for multi-port devices.
This should also fix the problem of failing to enumerate devices
because the PCI bridges have not yet been enabled at the time the iPXE
driver is loaded.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The linker chooses to look for _start first and always picks
efidrvprefix.o to satisfy it (probably because it's earlier in the
archive) which causes a multiple definition error when the linker
later has to pick efiprefix.o for other symbols.
Fix by using EFI-specific TGT_LD_FLAGS with an explicit entry point.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
elf2efi converts a suitable ELF executable (containing relocation
information, and with appropriate virtual addresses) into an EFI
executable. It is less tightly coupled with the gPXE build process
and, in particular, does not require the use of a hand-crafted PE
image header in efiprefix.S.
elf2efi correctly handles .bss sections, which significantly reduces
the size of the gPXE EFI executable.
Michael Brown