Someone at Dell must have a full-time job designing ways to screw up
implementations of INT 15,e820.  This latest gem is courtesy of a Dell
Xanadu system, which arbitrarily decides to obliterate the contents of
%esi.

Preserve %esi, %edi and %ebp across calls to INT 15,e820, in case
someone tries a variation on this trick in future.

FreeBSD requires the object format to be specified as elf_i386_fbsd,
rather than elf_i386.

Based on a patch from Eygene Ryabinkin <rea-fbsd@codelabs.ru>

Some PCI 3 BIOSes seem to provide a garbage value in %bx, which should
contain the runtime segment address.  Perform a basic sanity check: we
reject the segment if it is below the start of option ROM space.  If
the sanity check fails, we assume that the BIOS was not expecting us
to be a PCI 3 ROM, and we just leave our image in situ.

The section name seems to have significance for some versions of
binutils.

There is no way to instruct gcc that sections such as .bss16 contain
uninitialised data; it will emit them with contents explicitly set to
zero.  We therefore have to rely on the linker script to force these
sections to become uninitialised-data sections.  We do this by marking
them as NOLOAD; this seems to be the closest semantic equivalent in the
linker script language.

However, this gets ignored by some versions of ld (including 2.17 as
shipped with Debian Etch), which mark the resulting sections with
(CONTENTS,ALLOC,LOAD,DATA).  Combined with the fact that this version of
ld seems to ignore the specified LMA for these sections, this means that
they end up overlapping other sections, and so parts of .prefix (for
example) get obliterated by .data16's bss section.

Rename the .bss sections from .section_bss to .bss.section; this seems to
cause these versions of ld to treat them as uninitialised data.

Not fully understood, but it seems that the LMA of bss sections matters
for some newer binutils builds.  Force all bss sections to have an LMA
at the end of the file, so that they don't interfere with other
sections.

The symptom was that objcopy -O binary -j .zinfo would extract the
.zinfo section from bin/xxx.tmp as a blob of the correct length, but
with zero contents.  This would then cause the [ZBIN] stage of the
build to fail.

Also explicitly state that .zinfo(.*) sections have @progbits, in case
some future assembler or linker variant decides to omit them.

Some versions of ld choke on the "AT ( _xxx_lma )" in efi.lds with an
error saying "nonconstant expression for load base".  Since these were
only explicitly setting the LMA to the address that it would have had
anyway, they can be safely omitted.

We have EFI APIs for CPU I/O, PCI I/O, timers, console I/O, user
access and user memory allocation.

EFI executables are created using the vanilla GNU toolchain, with the
EXE header handcrafted in assembly and relocations generated by a
custom efilink utility.

The userptr_t is now the fundamental type that gets used for conversions.
For example, virt_to_phys() is implemented in terms of virt_to_user() and
user_to_phys().

We now have two implementations for the timer API: one using the
time-of-day counter at 40:70 and one using RDTSC.  Both make use of
timer2_udelay().

The copy_{to,from}_phys() functions were obsoleted long ago by
copy_{to,from}_user().

relocate_to() also disappeared some time ago.

Reduce the number of sections within the linker script to match the
number of practical sections within the output file.

Define _section, _msection, _esection, _section_filesz, _section_memsz,
and _section_lma for each section, replacing the mixture of symbols that
previously existed.

In particular, replace _text and _end with _textdata and _etextdata, to
make it explicit within code that uses these symbols that the .text and
.data sections are always treated as a single contiguous block.

Allow for the build CPU architecture and platform to be specified as part
of the make command goals.  For example:

  make bin/rtl8139.rom      # Standard i386 PC-BIOS build

  make bin-efi/rtl8139.efi  # i386 EFI build

The generic syntax is "bin[-[arch-]platform]", with the default
architecture being "i386" (regardless of the host architecture) and the
default platform being "pcbios".

Non-path targets such as "srcs" can be specified using e.g.

  make bin-efi srcs

Note that this changeset is merely Makefile restructuring to allow the
build architecture and platform to be determined by the make command
goals, and to export these to compiled code via the ARCH and PLATFORM
defines.  It doesn't actually introduce any new build platforms.

The arch/i386/Config file has long been marked as deprecated.  Move all
the pertinent bits to arch/i386/Makefile instead and remove
arch/i386/Config.

Although the E820 API allows for a caller to provide only a 20-byte
buffer, there exists at least one combination (HP BIOS, 32-bit WinPE)
that relies on information found only in the "extended attributes"
field, which requires a 24-byte buffer.

Allow for up to a 64-byte E820 buffer, in the hope of coping with
future idiocies like this one.

The ACPI specification defines an additional 4-byte field at offset 20
for an E820 memory map entry.  This field is presumably optional,
since generally E820 gets given only a 20-byte buffer to fill.
However, the bits of this optional field are defined as:

  bit 0 : region is enabled
  bit 1 : region is non-volatile memory rather than RAM

so it seems as though callers that pass in only a 20-byte buffer may
be missing out on some rather important information.

gcc should (I think) be warning about this anyway, but seems to do so
only when assertions are enabled for this object.

Our INT 15,e820 code was setting %es=%ss (as part of the "look ahead
in the memory map" logic), but failing to restore %es afterwards.
This is a serious bug, but wasn't affecting many platforms because
almost all callers seem to set %es=%ss anyway.

Use as "call dump_regs" from any real-mode code within .text16.
Should preserve all registers and flags.

Some BIOSes require us to pass in not only the continuation value (in
%ebx) as returned by the previous call to INT 15,e820 but also the
unmodified buffer (at %es:%di) as returned by the previous call to INT
15,e820.  Apparently, someone thought it would be a worthwhile
optimisation to fill in only the low dword of the "length" field and
the low byte of the "type field", assuming that the buffer would
remain unaltered from the previous call.

This problem was being triggered by the "peek ahead" logic in
get_mangled_e820(), which would read the next entry into a temporary
buffer in order to be able to guarantee terminating the map with
%ebx=0 rather than CF=1.  (Terminating with CF=1 upsets some Windows
flavours, despite being documented legal behaviour.)

Work around this problem by always fetching directly into our e820
cache; that way we can guarantee that the underlying call always sees
the previous buffer contents (and the same buffer address).

We seem to be having issues with various E820 memory maps.  These
problems are often difficult to reproduce, requiring access to the
specific system exhibiting the problem.

Add a facility for hooking in a fake E820 map generator, using an
arbitrary map defined in a C array, solely in order to be able to test
the map-mangling code against arbitrary E820 maps.

In particular, allow BANNER_TIMEOUT=0 to inhibit the prompt banners
altogether.

Ironically, this request comes from the same OEM that originally
required the prompts to be present during POST.

Based on a patch provided by XenSource for Etherboot 5.4.

Some really moronic BIOSes bring up the PXE stack via the UNDI loader
entry point during POST, and then don't bother to unload it before
overwriting the code and data segments.  If this happens, we really
don't want to leave INT 15 hooked, because that will cause any loaded
OS to die horribly as soon as it attempts to fetch the system memory
map.

We use a heuristic to detect whether or not we are being loaded at the
top of free base memory.  If we determine that we are being loaded at
some other arbitrary location in base memory, then we assume that it's
not safe to hook INT 15.

On non-BBS systems we hook INT 19, since there is no other way we can
guarantee gaining control of the flow of execution.  If we end up
doing this, prompt the user before attempting boot, since forcibly
capturing INT 19 is rather antisocial.

Some systems seem to report insane memory maps (particularly at POST
time).  Detect and work around some of the common failure cases.

If the INT 15,e820 memory map reports a region [0,0), this confuses
the "truncate to even megabytes" logic, which ends up rounding the
region 'down' to [0,fff00000).

Fix by ensuring that the region's end address is at least 1, before we
subtract 1 to obtain the "last byte in region" address.

INT 15,e801 is capable of returning a memory range that extends to
4GB, so allow for this in the debug message that shows the data
returned by INT 15,e801.

Apparently some BIOSes will place option ROMs on 512-byte boundaries.
While this is against specification, it doesn't actually hurt
anything, so we may as well increase our scan granularity to 512
bytes.

Contributed by Luca <lucarx76@gmail.com>

Wyse Streaming Manager server (WLDRM13.BIN) assumes that the PXENV+
entry point is at UNDI_CS:0000; apparently, somebody at Wyse has
difficulty distinguishing between the words "may" and "must"...

Add a dummy entry point at UNDI_CS:0000, which just jumps to the
correct entry point.

The multiboot specification states that, for raw images, if
load_end_addr is zero then it should be interpreted as meaning "use
the entire file", and if bss_end_addr is zero it should be interpreted
as meaning "no bss".

Explicitly state that we are using 32-bit addressing in 16-bit code.

GNU as 2.15 (FreeBSD/amd64 7-STABLE) got confused that 32-bit registers
are used in the code that was declared as 16-bit.  Add explicit modifier
'addr32' to make assembler happy.

Signed-off-by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>

IBM's iSCSI Firmware Initiator checks the UNDIROMID pointer in the
!PXE structure that gets created by the UNDI loader.  We didn't
previously fill this value in.

The IBM iSCSI Firmware Initiator complains that we don't have a bus
type field in the UNDI ROMID structure, so include one.

INT 1A,B101 (get PCI BIOS version) will overwrite %edi.

Include PMM allocation result in POST banner.

Include full product string in "starting execution" message.

Also mark ourselves as supporting DDIM in PnP header, for
completeness.

Commit 12f203c introduced a bug that caused the UNDI loader to attempt
to load the UNDI code and data segments to incorrect addresses.