[settings] Eliminate call to fetchf_named_setting() in expand_settings()
Use parse_setting_name() and fetchf_setting_copy() in
expand_settings(), to eliminate the call to fetchf_named_setting().
This change also eliminates the potentially large stack-allocated
buffer in expand_settings().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Change "not-found" semantics of fetch_setting_copy()
fetch_settings_copy() currently returns success and a NULL data
pointer to indicate a non-existent setting. This is intended to allow
the caller to differentiate between a non-existent setting and an
error in allocating memory for the copy of the setting.
The underlying settings blocks' fetch() methods provide no way to
perform an existence check separate from an attempt to fetch the
setting. A "non-existent setting" therefore means simply a setting
for which an error was encountered when attempting to fetch from every
settings block within the subtree.
Since any underlying error within a settings block (e.g. a GuestRPC
failure when attempting to retrieve a VMware GuestInfo setting) will
produce the effect of a "non-existent setting", it seems somewhat
meaningless to give special treatment to memory allocation errors
within fetch_setting_copy().
Remove the special treatment and simplify the semantics of
fetch_setting_copy() by directly passing through any underlying error
(including non-existence) encountered while fetching the setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Clarify usage of the term "named setting"
There are currently two conflicting usages of the term "named setting"
within iPXE: one refers to predefined settings (such as show up in the
"config" UI), the other refers to settings identified by a name (such
as "net0.dhcp/ip").
Split these usages into the term "predefined setting" and "named
setting" to avoid ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Our use of --gc-sections causes the linker to discard the symbols
defined by FILE_LICENCE(), meaning that the resulting licence
determination is incomplete.
We must use the KEEP() directive in the linker script to force the
linker to not discard the licence symbols. Using KEEP(*(COMMON))
would be undesirable, since there are some symbols in COMMON which we
may wish to discard.
Fix by placing symbols defined by PROVIDE_SYMBOL() (which is used by
FILE_LICENCE()) into a special ".provided" section, which we then mark
with KEEP(). All such symbols are zero-length, so there is no cost in
terms of the final binary size.
Since the symbols are no longer in COMMON, the linker will reject
symbols with the same name coming from multiple objects. We therefore
append the object name to the licence symbol, to ensure that it is
unique.
Reported-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ifmgmt] Avoid relying on global variable within ifcommon_exec()
The getopt API defines optind as a global variable. When used by the
"autoboot" command, the payload function passed to ifcommon_exec() may
result in a new iPXE script being executed; the commands therein would
then overwrite the value of optind. On returning, ifcommon_exec()
would continue processing the list of interfaces from an undefined
point.
Fix by using a local variable to hold the index within the list of
interfaces.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some hardware (observed with an onboard RTL8168) will erroneously
report a buffer overflow error if the received packet exactly fills
the receive buffer.
Fix by adding an extra four bytes of padding to each receive buffer.
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Add support for navigation keys in "config" user interface
Add support for page up, page down, home and end keys, matching the
navigation logic used in the menu user interface.
Originally-implemented-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[script] Allow for backslash continuation of script lines
Allow long script lines to be broken up using backslash continuation.
For example:
choose --default linux --timeout 3000 os \
&& goto boot_${os} || goto cancelled
Requested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[base16] Ensure base16_encode() always terminates its result string
base16_encode() will fail to generate a terminating NUL if the length
of the raw data is zero, since the loop calling sprintf() will never
execute.
Fix by explicitly terminating the result with a NUL.
Reported-by: Marin Hannache <git@mareo.fr>
Debugged-by: Marin Hannache <git@mareo.fr>
Tested-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the old via-rhine driver with a new version using the iPXE
API.
Includes fixes by Thomas Miletich for:
- MMIO access
- Link detection
- RX completion in RX overflow case
- Reset and EEPROM reloading
- CRC stripping
- Missing cpu_to_le32() calls
- Missing memory barriers
Signed-off-by: Adrian Jamróz <adrian.jamroz@gmail.com>
Modified-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Modified-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[lotest] Include sequence number within loopback test packets
Include a sequence number as the first four bytes of the loopback test
packet payload. When a content mismatch occurs, this gives some
information about the source of the mismatched packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow any iPXE command expecting a network device name to accept
"netX" as a synonym for "most recently opened network device".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Make "netX" settings block function as a symbolic link
Add a facility for settings blocks to act as symbolic links to other
settings blocks, and reimplement the "netX" virtual settings block
using this facility.
The primary advantage of this approach is that unscoped settings such
as ${mac} and ${filename} will now reflect the settings obtained from
the most recently opened network device: in most cases, this will mean
the settings obtained from the most recent DHCP attempt. This should
improve conformance to the principle of least astonishment.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Expose PCI configuration space via settings mechanism
Allow values to be read from PCI configuration space using the syntax
${pci/<busdevfn>.<offset>.<length>}
where <busdevfn> is the bus:dev.fn address of the PCI device
(expressed as a single integer, as returned by ${net0/busloc}),
<offset> is the offset within PCI configuration space, and <length> is
the length within PCI configuration space.
Values are returned in reverse byte order, since PCI configuration
space is little-endian by definition.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Move VMWARE_SETTINGS build configuration option from config/sideband.h
to a new config/settings.h.
Existing instances of config/local/sideband.h will not be affected,
since config.c still #includes config/sideband.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow network device's "busloc" setting to be formatted as a PCI
bus:dev.fn address using e.g. ${net0/busloc:busdevfn}.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hex_decode() to parse "hex" and "hexhyp" settings. Note that this
parser is stricter than the old parser; it now requires exactly two
hex digits for each byte. (The old parser was based upon strtoul()
and so would allow leading whitespace and a leading plus or minus
sign.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[base16] Generalise base16_decode() to hex_decode()
Provide a generic hex_decode() routine which can be shared between the
Base16 code and the "hex" and "hexhyp" settings parsers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tcp] Do not send RST for unrecognised connections
On large networks with substantial numbers of monitoring agents,
unwanted TCP connection attempts may end up flooding iPXE's ARP cache.
Fix by silently dropping packets received for unrecognised TCP
connections. This should not cause problems, since many firewalls
will also silently drop any such packets.
Reported-by: Jarrod Johnson <jarrod.b.johnson@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[autoboot] Use next-server from filename's settings block
Locate the settings block containing the filename, and search only
that settings block for the next-server address. This avoids problems
caused by misconfigured DHCP servers which provide a next-server
address (often defaulting to the DHCP server's own IP address) even
when not providing a filename.
Originally-implemented-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc 4.8 and 4.9 fail to compile pxe_call.c with the error "bp cannot
be used in asm here". Other points in the codebase which use "ebp" in
the asm clobber list do not seem to be affected.
Unfortunately gcc provides no way to specify %ebp as an output
register, so we cannot use this as a workaround. The only viable
solution is to explicitly push/pop %ebp within the asm itself. This
is ugly for two reasons: firstly, it may be unnecessary; secondly, it
may cause gcc to generate invalid %esp-relative addresses if the asm
happens to use memory operands. This specific block of asm uses no
memory operands and so will not generate invalid code.
Reported-by: Daniel P. Berrange <berrange@redhat.com>
Reported-by: Christian Hesse <list@eworm.de>
Originally-fixed-by: Christian Hesse <list@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of Linux apparently complain if initrds are not aligned
to a page boundary. Fix by changing INITRD_ALIGN from 4 bytes to 4096
bytes.
The amount of padding at the end of each initrd will now often be
sufficient to allow the cpio header to be prepended without crossing
an alignment boundary. The final location of the initrd may therefore
end up being slightly higher than the post-shuffle location.
bzimage_load_initrd() must therefore now copy the initrd body prior to
copying the cpio header, otherwise the start of the initrd body may be
overwritten by the cpio header. (Note that the guarantee that an
initrd will never need to overwrite an initrd at a higher location
still holds, since the overall length of each initrd cannot decrease
as a result of adding a cpio header.)
Reported-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown