gPXE currently overwrites the filename stored in the cached DHCP
packets when a call to PXENV_TFTP_READ_FILE or PXENV_RESTART_TFTP is
made. This code has existed for many years as a workaround for RIS,
which seemed to require that this be done.
pxe_set_cached_filename() causes problems with the Bootix NBP, and a
recent test demonstrates that RIS will complete successfully even with
pxe_set_cached_filename() removed. There have been many changes to
the DHCP and PXE logic since this code was first added, and it is
quite plausible that it was masking a bug that no longer exists.
Reported-by: Alex Zeffertt <alex.zeffertt@eu.citrix.com>
Debugged-by: Shao Miller <Shao.Miller@yrdsb.edu.on.ca>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
[pxe] Avoid potential interrupt storms when using shared interrupts
Current gPXE code always returns "OURS" in response to
PXENV_UNDI_ISR:START. This is harmless for non-shared interrupt
lines, and avoids the complexity of trying to determine whether or not
we really did cause the interrupt. (This is a non-trivial
determination; some drivers don't have interrupt support and hook the
system timer interrupt instead, for example.)
A problem occurs when we have a shared interrupt line, the other
device asserts an interrupt, and the controlling ISR does not chain to
the other device's ISR when we return "OURS". Under these
circumstances, the other device's ISR never executes, and so the
interrupt remains asserted, causing an interrupt storm.
Work around this by returning "OURS" if and only if our net device's
interrupt is currently recorded as being enabled. Since we always
disable interrupts as a result of a call to PXENV_UNDI_ISR:START, this
guarantees that we will eventually (on the second call) return "NOT
OURS", allowing the other ISR to be called. Under normal operation,
including a non-shared interrupt situation, this change will make no
difference since PXENV_UNDI_ISR:START would be called only when
interrupts were enabled anyway.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
[phantom] Update interrupt support to match current firmware
The interrupt control mechanism on Phantom cards has changed
substantially since the driver was initially written. This updates
the code to match the mechanism used in production firmware.
This is sufficient to allow DOS wget to function successfully using
the 3Com UNDI/NDIS, Intel UNDI/NDIS, and UNDIPD.COM UNDI/PD stacks.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
This commit adds an igb (Intel GigaBit) driver based on Intel source
code available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support some PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit adds an e1000e driver based on Intel source code
available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support many PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit replaces the current gPXE e1000 driver with one ported
from Intel source code available at
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support most if not all PCI e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[vxge] Add stub vxge.c file so bin/vxge.usb can be built
The vxge driver code is split over several files, including vxge_main.c.
This causes the build system and ROM-o-matic to see the driver as
"vxge_main".
This patch adds a stub vxge.c which takes up no space but gives the
driver its proper name, "vxge".
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The function recorder is a crash and hang debugging tool. It logs each
function call into a memory buffer while gPXE runs. After the machine
is reset, and if the contents of memory have not been overwritten, gPXE
will detect the memory buffer and print out its contents.
This allows developers to see a trace of the last functions called
before a crash or hang. The util/fnrec.sh script can be used to convert
the function addresses back into symbol names.
To build with fnrec:
make FNREC=1
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Embedded image support uses .incbin in inline assembly to include binary
files. The file dependency is not spotted by ccache when deciding
whether or not to rebuild embedded.o. This results in builds that
contain an outdated version of the embedded image when ccache is used.
Reported-by: Tim 'Shaggy' Bielawa <tbielawa@jabber.org>
Reported-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Embedded image support uses .incbin in inline assembly to include binary
files. The file dependency is not spotted by ccache when deciding
whether or not to rebuild embedded.o. This results in builds that
contain an outdated version of the embedded image when ccache is used.
Reported-by: Tim 'Shaggy' Bielawa <tbielawa@jabber.org>
Reported-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
In the actual SYSLINUX suite's comboot implementation, the version
string is prefixed by CR LF, and the copyright string has a leading
space. Some tools (specifically HDT) assume these padding characters
exist, so we should probably return strings in a similar format.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
Loading multiple UNDI instances would be useful in systems that have
several network cards with vendor PXE ROMs. However, we cannot rely on
UNDI ROMs working correctly with multiple instances loaded
simultaneously.
The gPXE UNDI driver supports the following multi-NIC configurations:
1. Chainloading undionly.kpxe on a specific NIC.
2. Loading the UNDI driver for the first probed device and ignoring all
other UNDI devices in the system.
This patch refuses to probe additional UNDI devices so there can never
be multiple instances of UNDI loaded.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Debian based systems may have genisoimage(1) instead of mkisofs(1).
They are command-line compatible so the util/geniso script should be
able to choose either one.
This patch also changes the use of the mkisofs quiet (-q) flag to its
long form (-quiet). This should be compatible with more versions of
cdrtools and cdrkit.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[hermon] Change hermon_alloc_icm() to conform to ConnectX2 requirements
Align each ICM member alloc to the member size instead of page size.
Increase multicast table size to 128.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The NMB protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The IGMP code came from legacy Etherboot and was never updated to work
as a gPXE protocol. There has been no demand for this protocol, so this
patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The NFS protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
I have an unfinished NFSv3 over TCP implementation for gPXE that can be
used as the base for new work, should we want to resurrect this
protocol.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The FSP protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The .elf, .elfd, .lmelf, and .lmelfd prefices were brought over from
legacy Etherboot and they do not build in gPXE. This patch removes the
ELF prefices.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The unfinished .exe prefix was brought over from legacy Etherboot.
There has been no demand for .exe images so this patch removes the
prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The DOS .com prefix was brought over from legacy Etherboot but does not
build. There has been no demand for .com images so this patch removes
the prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The .lkrn prefix allows gPXE to be loaded as a Linux bzImage. The
bImage prefix was carried over from legacy Etherboot and does not build.
This patch removes the .bImage prefix, use .lkrn instead.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Commit 3d9dd93 introduced a regression in HTTP: if a URI without a
path is specified (e.g. http://netboot.me), we send the empty string
as our GET request. Reintroduce an extra slash when uri->path is NULL,
to turn this into the expected GET /.
Reported-by: Kyle Kienapfel <doctor.whom@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[uri] Handle an empty unparse_uri() result properly
Previously, if none of the URI parts requested existed in the passed
URI, unparse_uri() would not touch the destination buffer at all; this
could lead to use of uninitialized data. Fix by setting buf[0] = '\0'
before unparsing whenever we have room to do so.
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The rtl818x driver uses programmed I/O but has a fallback to
memory-mapped I/O registers. The fallback currently will not work since
the registers are accessed using inl()/outl() programmed I/O functions
in the driver. This patch removes the fallback to we fail cleanly when
programmed I/O is not possible.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
This driver uses programmed I/O to access hardware registers. There is
a stray memory-mapped I/O read on a programmed I/O address. Perhaps
this is an artifact of porting the driver. Fix this by converting it to
programmed I/O.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
It might be the case that we wish to chain to an NBP without
being "in the way". We now implement a hook in our exit path
for gPXE *.*pxe build targets. The hook is a pointer to a
SEG16:OFF16 which we try to jump to during exit. By default,
this pointer results in the usual exit path.
We also implement the "pxenv_file_exit_hook" PXE API routine
to allow the user to specify an alternate SEG16:OFF16 to jump
to during exit.
Unfortunately, this additional PXE extension has a cost
in code size. Fortunately, a look at the size difference
for a gPXE .rom build target shows zero size difference
after compression.
The routine is documented in doc/pxe_extensions as follows:
FILE EXIT HOOK
Op-Code: PXENV_FILE_EXIT_HOOK (00e7h)
Input: Far pointer to a t_PXENV_FILE_EXIT_HOOK parameter
structure that has been initialized by the caller.
Output: PXENV_EXIT_SUCCESS or PXENV_EXIT_FAILURE must be
returned in AX. The Status field in the parameter
structure must be set to one of the values represented
by the PXENV_STATUS_xxx constants.
Description:Modify the exit path to jump to the specified code.
Only valid for pxeprefix-based builds.
typedef struct s_PXENV_FILE_EXIT_HOOK {
PXENV_STATUS_t Status;
SEGOFF16_t Hook;
} t_PXENV_FILE_EXIT_HOOK;
Set before calling API service:
Hook: The SEG16:OFF16 of the code to jump to.
Returned from API service:
Status: See PXENV_STATUS_xxx constants.
Requested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[dhcp] Keep multiple DHCP offers received, and use them intelligently
Instead of keeping only the best IP and PXE offers, store all of them,
and pick the best to use just before a request is sent. This allows
priority differentiation to work even when lower-priority offers
provide PXE options, and improves robustness at sites with broken PXE
servers intermingled with working ones: when a ProxyDHCP request times
out, instead of giving up, we try the next PXE offer we've received.
It also allows us to avoid breaking up combined IP+PXE offers, which
can be important with some firewall configurations. This behavior
matches that of most vendor PXE ROMs.
Store a reference to the DHCPOFFER packet in the offer structure, so
that when registering settings after a successful ACK we can register
the proxy PXE settings we originally received; this removes the need
for a nonstandard duplicate REQUEST/ACK to port 67 of proxy servers
like dnsmasq that provide PXE options in the OFFER.
Total cost: 450 bytes uncompressed.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This seems to be necessary for some types of PCI devices. We had
problems when using gPXE in KVM virtual machines with direct
PCI device access.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Modified-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[ftp] User and password URI support for the FTP protocol
The default user and password are used for anonymous FTP by default.
This patch adds support for an explicit user name and password in an FTP
URI:
imgfetch ftp://user:password@server.com/path/to/file
Edited-by: Stefan Hajnoczi <stefanha@gmail.com>. Bugs are my fault.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Currently, handling of URI escapes is ad-hoc; escaped strings are
stored as-is in the URI structure, and it is up to the individual
protocol to unescape as necessary. This is error-prone and expensive
in terms of code size. Modify this behavior by unescaping in
parse_uri() and escaping in unparse_uri() those fields that typically
handle URI escapes (hostname, user, password, path, query, fragment),
and allowing unparse_uri() to accept a subset of fields to print so
it can be easily used to generate e.g. the escaped HTTP path?query
request.
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[settings] Add automagic "netX" settings block for last opened netdev
A script loaded via autoboot may want to get some of the settings (MAC
address, IP address, et cetera) for the interface via which it was
loaded, in order to pass them to the operating system. Previously such
a script had no way to determine what to put in the X of ${netX/foo}.
Solve this problem by transparently forwarding accesses to the real
settings associated with the most recently opened network device,
so scripts in this situation can say literally ${netX/foo} and get
the foo setting they want.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[prefix] Add .xrom prefix for a ROM that loads itself by PCI accesses
The standard option ROM format provides a header indicating the size
of the entire ROM, which the BIOS will reserve space for, load, and
call as necessary. However, this space is strictly limited to 128k for
all ROMs. gPXE ameliorates this somewhat by reserving space for itself
in high memory and relocating the majority of its code there, but on
systems prior to PCI3 enough space must still be present to load the
ROM in the first place. Even on PCI3 systems, the BIOS often limits the
size of ROM it will load to a bit over 64kB.
These space problems can be solved by providing an artificially small
size in the ROM header: just enough to let the prefix code (at the
beginning of the ROM image) be loaded by the BIOS. To the BIOS, the
gPXE ROM will appear to be only a few kilobytes; it can then load
the rest of itself by accessing the ROM directly using the PCI
interface reserved for that task.
There are a few problems with this approach. First, gPXE needs to find
an unmapped region in memory to map the ROM so it can read from it;
this is done using the crude but effective approach of scanning high
memory (over 0xF0000000) for a sufficiently large region of all-ones
(0xFF) reads. (In x86 architecture, all-ones is returned for accesses
to memory regions that no mapped device can satisfy.) This is not
provably valid in all situations, but has worked well in practice.
More importantly, this type of ROM access can only work if the PCI ROM
BAR exists at all. NICs on physical add-in PCI cards generally must
have the BAR in order for the BIOS to be able to load their ROM, but
ISA cards and LAN-on-Motherboard cards will both fail to load gPXE
using this scheme.
Due to these uncertainties, it is recommended that .xrom only be used
when a regular .rom image is infeasible due to crowded option ROM
space. However, when it works it could allow loading gPXE images
as large as a flash chip one could find - 128kB or even higher.
Signed-off-by: Marty Connor <mdc@etherboot.org>
For extremely tight space requirements and specific applications, it is
sometimes desirable to create gPXE images that cannot provide the PXE API
functionality to client programs. Add a configuration header option,
PXE_STACK, that can be removed to remove this stack. Also add PXE_MENU
to control the PXE boot menu, which most uses of gPXE do not need.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[pxe] Support cached DHCP packets in .kkpxe images
If we don't unload the PXE stack before executing gPXE, automatically
take advantage of the cached DHCPACK that the underlying/parent PXE
stack can provide. If that cached DHCPACK contains option 175.178, or
the user sets the use-cached setting before invoking DHCP, the real
DHCP request will be skipped and the cached DHCPACK will be used for
network configuration. Otherwise, the cached settings block is thrown
away as soon as a fresh one is acquired.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[dhcp] Add generic facility for using cached network settings
When a DHCP session is started (using autoboot or a command-line `dhcp
net0'), check whether the new setting use-cached (DHCP option 175.178)
is TRUE; if so, skip DHCP and rely on currently registered
settings. This lets one combine a static IP with autoboot.
Before checking the use-cached setting, call a weak
get_cached_dhcpack() hook that can be implemented by particular builds
of gPXE supporting some fashion of retrieving a cached DHCPACK packet.
If one is available, it is registered as an options source, and then
either that packet's option 175.178 or the user's prior manual
use-cached setting can allow skipping duplicate DHCP.
Using cached packets is not the default because DHCP servers are often
configured to give gPXE different options than they give a vendor PXE
client; in order to break the infinite loop of PXE chaining, one would
need to load a gPXE with an embedded image that does something more
than autoboot.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[pxe] Separate parent PXE API caller from UNDINET driver
Calling the parent PXE stack (the stack that loaded us, for
undionly.kkpxe) can be useful for more than UNDI calls; for instance,
it lets us get cached DHCP packets to avoid re-DHCP when working with
embedded images.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Weak symbols are a useful tool in eliminating unnecessary dependencies
between object files, but they are somewhat dangerous because one must
remember to test the weak symbol against NULL before using it. To
rectify that, add macros for declaring weak functions that will return
a default value inline if the file defining them is not available at
link time.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Michael Brown