[romprefix] Provide indication of successful call to install_prealloc
The existing "iPXE starting execution" message indicates that the BEV
(or INT19) was invoked, but gives no indication on whether or not the
iPXE source was successfully retrieved (e.g. from PMM). Split the
"starting execution message" into "starting execution...ok"; the "ok"
indicates that the main iPXE body was successfully decompressed and
relocated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[prefix] Default to 1MB mark as fallback high memory load point
Now that we can use odd megabytes, there is no particular need to use
an even megabyte as the fallback temporary load point.
Note that the old warnings about avoiding 2MB pre-date our ability to
cooperate with other PXE ROMs by using PMM.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE is now capable of operating in odd megabytes of memory, so remove
the obsolete code enforcing an even-megabyte constraint.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Use libflat to enable A20 line on each real-to-protected transition
Use the shared code in libflat to perform the A20 transitions
automatically on each transition from real to protected mode. This
allows us to remove all explicit calls to gateA20_set().
The old warnings about avoiding automatically enabling A20 are
essentially redundant; they date back to the time when we would always
start hammering the keyboard controller without first checking to see
if gate A20 was already enabled (which it almost always is).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently insists on residing in an even megabyte. This imposes
undesirably severe constraints upon our PMM allocation strategy, and
limits our options for mechanisms to access ROMs greater than 64kB in
size.
Add A20 handling code to libflat so that prefixes are able to access
memory even in odd megabytes.
The algorithms and tuning parameters in the new A20 handling code are
based upon a mixture of the existing iPXE A20 code and the A20 code
from the 2.6.32 Linux kernel.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The flatten_real_mode routine is not needed until after decompressing
.text16.early, and currently performs various contortions to
compensate for the fact that .prefix may not be writable. Move
flatten_real_mode to .text16.early to save on (compressed) binary size
and simplify the code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a section .text16.early which is always kept inline with the
prefix. This will allow for some code sharing between the .prefix and
.text16 sections.
Note that the simple solution of just prepending the .prefix section
to the .text16 section will not work, because a bug in Wyse Streaming
Manager server (WLDRM13.BIN) requires us to place a dummy PXENV+ entry
point at the start of .text16.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[prefix] Use flat real mode for access to high memory
Use flat real mode rather than 16-bit protected mode for access to
high memory during installation. This simplifies the code by reducing
the number of CPU modes we need to think about, and also increases the
amount of code in common between the normal and (somewhat
hypothetical) KEEP_IT_REAL methods of operation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When returning to real mode, set 4GB segment limits instead of 64kB
limits. This change improves our chances of successfully returning to
a PMM-capable BIOS aftering entering iPXE during POST; the BIOS will
have set up flat real mode before calling our initialisation point,
and may be disconcerted if we then return in genuine real mode.
This change is unlikely to break anything, since any code that might
potentially access beyond 64kB must use addr32 prefixes to do so; if
this is the case then it is almost certainly code written to expect
flat real mode anyway.
Note that it is not possible to restore the real-mode segment limits
to their original values, since it is not possible to know which
protected-mode segment descriptor was originally used to initialise
the limit portion of the segment register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The .hrom prefix provides an experimental mechanism for reducing
option ROM space usage on systems where PMM allocation fails, by
pretending that PMM allocation succeeded and gave us an address fixed
at compilation time. This is unreliable, and potentially dangerous.
In particular, when multiple gPXE ROMs are present in a system, each
gPXE ROM will assume ownership of the same fixed address, resulting in
undefined behaviour.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The .xrom prefix provides an experimental mechanism for loading ROM
images greater than 64kB in size by mapping the expansion ROM BAR in
at a hopefully-unused address. This is unreliable, and potentially
dangerous. In particular, there is no guarantee that any PCI bridges
between the CPU and the device will respond to accesses for the
"unused" memory region that is chosen, and it is possible that the
process of scanning for the "unused" memory region may end up issuing
reads to other PCI devices. If this ends up trampling on a register
with read side-effects belonging to an unrelated PCI device, this may
cause undefined behaviour.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Christopher Armenio reported link detection problems with an
integrated eepro100 NIC. Thomas Miletich removed link detection code
from the eepro100 driver and verified that the driver continued to
function. Christopher verified Thomas' patch on his integrated
eepro100 NIC.
Reported-by: Christopher Armenio <christopher.armenio@resquared.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
In building gpxe for openSUSE Factory (part of kvm package), there were
a few problems identified by the compiler. This patch addresses them.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Include config/local/$file in config/$file where it makes sense and
create empty local configs during build if not present.
Modified-by: Michael Brown <mcb30@etherboot.org>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
gPXE currently overwrites the filename stored in the cached DHCP
packets when a call to PXENV_TFTP_READ_FILE or PXENV_RESTART_TFTP is
made. This code has existed for many years as a workaround for RIS,
which seemed to require that this be done.
pxe_set_cached_filename() causes problems with the Bootix NBP, and a
recent test demonstrates that RIS will complete successfully even with
pxe_set_cached_filename() removed. There have been many changes to
the DHCP and PXE logic since this code was first added, and it is
quite plausible that it was masking a bug that no longer exists.
Reported-by: Alex Zeffertt <alex.zeffertt@eu.citrix.com>
Debugged-by: Shao Miller <Shao.Miller@yrdsb.edu.on.ca>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
[pxe] Avoid potential interrupt storms when using shared interrupts
Current gPXE code always returns "OURS" in response to
PXENV_UNDI_ISR:START. This is harmless for non-shared interrupt
lines, and avoids the complexity of trying to determine whether or not
we really did cause the interrupt. (This is a non-trivial
determination; some drivers don't have interrupt support and hook the
system timer interrupt instead, for example.)
A problem occurs when we have a shared interrupt line, the other
device asserts an interrupt, and the controlling ISR does not chain to
the other device's ISR when we return "OURS". Under these
circumstances, the other device's ISR never executes, and so the
interrupt remains asserted, causing an interrupt storm.
Work around this by returning "OURS" if and only if our net device's
interrupt is currently recorded as being enabled. Since we always
disable interrupts as a result of a call to PXENV_UNDI_ISR:START, this
guarantees that we will eventually (on the second call) return "NOT
OURS", allowing the other ISR to be called. Under normal operation,
including a non-shared interrupt situation, this change will make no
difference since PXENV_UNDI_ISR:START would be called only when
interrupts were enabled anyway.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
[phantom] Update interrupt support to match current firmware
The interrupt control mechanism on Phantom cards has changed
substantially since the driver was initially written. This updates
the code to match the mechanism used in production firmware.
This is sufficient to allow DOS wget to function successfully using
the 3Com UNDI/NDIS, Intel UNDI/NDIS, and UNDIPD.COM UNDI/PD stacks.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
This commit adds an igb (Intel GigaBit) driver based on Intel source
code available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support some PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit adds an e1000e driver based on Intel source code
available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support many PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit replaces the current gPXE e1000 driver with one ported
from Intel source code available at
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support most if not all PCI e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
[vxge] Add stub vxge.c file so bin/vxge.usb can be built
The vxge driver code is split over several files, including vxge_main.c.
This causes the build system and ROM-o-matic to see the driver as
"vxge_main".
This patch adds a stub vxge.c which takes up no space but gives the
driver its proper name, "vxge".
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The function recorder is a crash and hang debugging tool. It logs each
function call into a memory buffer while gPXE runs. After the machine
is reset, and if the contents of memory have not been overwritten, gPXE
will detect the memory buffer and print out its contents.
This allows developers to see a trace of the last functions called
before a crash or hang. The util/fnrec.sh script can be used to convert
the function addresses back into symbol names.
To build with fnrec:
make FNREC=1
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Embedded image support uses .incbin in inline assembly to include binary
files. The file dependency is not spotted by ccache when deciding
whether or not to rebuild embedded.o. This results in builds that
contain an outdated version of the embedded image when ccache is used.
Reported-by: Tim 'Shaggy' Bielawa <tbielawa@jabber.org>
Reported-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
In the actual SYSLINUX suite's comboot implementation, the version
string is prefixed by CR LF, and the copyright string has a leading
space. Some tools (specifically HDT) assume these padding characters
exist, so we should probably return strings in a similar format.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
Loading multiple UNDI instances would be useful in systems that have
several network cards with vendor PXE ROMs. However, we cannot rely on
UNDI ROMs working correctly with multiple instances loaded
simultaneously.
The gPXE UNDI driver supports the following multi-NIC configurations:
1. Chainloading undionly.kpxe on a specific NIC.
2. Loading the UNDI driver for the first probed device and ignoring all
other UNDI devices in the system.
This patch refuses to probe additional UNDI devices so there can never
be multiple instances of UNDI loaded.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Debian based systems may have genisoimage(1) instead of mkisofs(1).
They are command-line compatible so the util/geniso script should be
able to choose either one.
This patch also changes the use of the mkisofs quiet (-q) flag to its
long form (-quiet). This should be compatible with more versions of
cdrtools and cdrkit.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[hermon] Change hermon_alloc_icm() to conform to ConnectX2 requirements
Align each ICM member alloc to the member size instead of page size.
Increase multicast table size to 128.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The NMB protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The IGMP code came from legacy Etherboot and was never updated to work
as a gPXE protocol. There has been no demand for this protocol, so this
patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The NFS protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
I have an unfinished NFSv3 over TCP implementation for gPXE that can be
used as the base for new work, should we want to resurrect this
protocol.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The FSP protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The .elf, .elfd, .lmelf, and .lmelfd prefices were brought over from
legacy Etherboot and they do not build in gPXE. This patch removes the
ELF prefices.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The unfinished .exe prefix was brought over from legacy Etherboot.
There has been no demand for .exe images so this patch removes the
prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The DOS .com prefix was brought over from legacy Etherboot but does not
build. There has been no demand for .com images so this patch removes
the prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The .lkrn prefix allows gPXE to be loaded as a Linux bzImage. The
bImage prefix was carried over from legacy Etherboot and does not build.
This patch removes the .bImage prefix, use .lkrn instead.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Commit 3d9dd93 introduced a regression in HTTP: if a URI without a
path is specified (e.g. http://netboot.me), we send the empty string
as our GET request. Reintroduce an extra slash when uri->path is NULL,
to turn this into the expected GET /.
Reported-by: Kyle Kienapfel <doctor.whom@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
[uri] Handle an empty unparse_uri() result properly
Previously, if none of the URI parts requested existed in the passed
URI, unparse_uri() would not touch the destination buffer at all; this
could lead to use of uninitialized data. Fix by setting buf[0] = '\0'
before unparsing whenever we have room to do so.
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Michael Brown