[usb] Maintain single lists of halted endpoints and changed ports
When an EHCI hotplug action results in the controller disowning the
port, it will result in a hotplug action on the corresponding UHCI or
OHCI controller. Allow such hotplug actions to be carried out as part
of the same call to usb_step() or usb_register_bus(), by maintaining a
single central list of changed ports.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The USB core will currently fail to detect disconnections if a new
device has attached by the time the port is examined in
usb_hotplug().
Fix by recording the fact that a disconnection has taken place
whenever the "connection status changed" (CSC) bit is observed to be
set. (Whether the change represents a disconnection or a
reconnection, it indicates that the port has experienced some time of
being disconnected.)
Note that the time at which a disconnection can be detected varies by
hub type. In particular: root hubs can observe the CSC bit when
polling, and so will record the disconnection before calling
usb_port_changed(), but USB hubs read the port status (and hence the
CSC bit) only during the call to hub_speed(), long after the call to
usb_port_changed().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pci] Provide PCI_CLASS() to calculate a scalar PCI class value
Rename PCI_CLASS() (which constructs a struct pci_class_id) to
PCI_CLASS_ID(), and provide PCI_CLASS() as a macro which constructs
the 24-bit scalar value of a PCI class code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Include setup packet within I/O buffer for message transfers
The USB API currently assumes that host controllers will have
immediate data buffer space available in which to store the setup
packet. This is true for xHCI, partially true for EHCI (which happens
to have 12 bytes of padding in each transfer descriptor due to
alignment requirements), and not true at all for UHCI.
Include the setup packet within the I/O buffer passed to the host
controller's message() method, thereby eliminating the requirement for
host controllers to provide immediate data buffers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[vram] Add "vram" built-in setting to dump video RAM
The "vram" setting returns the (Base64-encoded) contents of video RAM,
and can be used to capture a screenshot. For example: after running
memtest.0 and encountering an error, the output can be captured and
sent to a remote server for later diagnosis:
#!ipxe
chain -a http://server/memtest.0 && goto ok || goto bad
:bad
params
param errno ${errno}
param vram ${vram}
chain -a http://server/report.php##params
:ok
Inspired-by: Christian Nilsson <nikize@gmail.com>
Originally-implemented-by: Christian Nilsson <nikize@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[base16] Add buffer size parameter to base16_encode() and base16_decode()
The current API for Base16 (and Base64) encoding requires the caller
to always provide sufficient buffer space. This prevents the use of
the generic encoding/decoding functionality in some situations, such
as in formatting the hex setting types.
Implement a generic hex_encode() (based on the existing
format_hex_setting()), implement base16_encode() and base16_decode()
in terms of the more generic hex_encode() and hex_decode(), and update
all callers to provide the additional buffer length parameter.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[test] Include IPv6 support when performing settings self-tests
The settings self-tests include tests for the "ipv6" setting type.
When IPv6 support is not included, this setting type exists (since it
is referred to by some dual-stack code, such as dns.c) but is
non-functional.
Force IPv6 support to be included within a settings self-test build
using an explicit REQUIRE_OBJECT() macro.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ath9k] Remove confusing logic inversion in an ANI variable
This changed in Linux kernel the same way in commit 7067e701
("ath9k_hw: remove confusing logic inversion in an ANI variable") by
Felix Fietkau.
Additionally this fixes "error: logical not is only applied to the
left hand side of comparison" with GCC 5.1.0.
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This fixes "initialization discards 'const' qualifier from pointer
target type" warnings with GCC 5.1.0.
Signed-off-by: Christian Hesse <mail@eworm.de>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Add PCI device IDs for Intel I218-LM and I218-V
I218-LM (rev 3) is found in Lenovo Thinkpad X250. The remaining
device IDs are from linux/drivers/net/ethernet/intel/e1000e/hw.h
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Construct all-drivers list based on driver class
The USB bus drivers (ehci.c and xhci.c) have PCI device ID tables and
hence PCI_ROM() lines, but should probably not be included in the
all-drivers build on this basis, since they do nothing useful unless a
USB network driver is also present.
Fix by constructing the all-drivers list based on the driver class
(i.e. the portion of the source path immediately after "drivers/").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[realtek] Do not attempt to access EEPROM on RTL8169 chips
On some RTL8169 onboard NICs (observed with a Lenovo ThinkPad 11e),
the EEPROM is not merely not present: any attempt to read from the
non-existent EEPROM will crash and reboot the system.
The equivalent code to read from the EEPROM was removed from the Linux
r8169 driver in 2009 with a comment suggesting that it was similarly
found to be unreliable on some systems.
Fix by accessing the EEPROM only on RTL8139 NICs, and assuming that
the MAC address will always be correctly preset on RTL8169 NICs.
Reported-by: Evan Prohaska <eprohaska@edkey.org>
Tested-by: Evan Prohaska <eprohaska@edkey.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Force RX polling on VMware emulated 82545em
The emulated Intel 82545em in some versions of VMware (observed with
ESXi v5.1) seems to sometimes fail to set the RXT0 bit in the
interrupt cause register (ICR), causing iPXE to stop receiving
packets. Work around this problem (for the 82545em only) by always
polling the receive queue regardless of the state of the ICR.
Reported-by: Slava Bendersky <volga629@networklab.ca>
Tested-by: Slava Bendersky <volga629@networklab.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The assembler on OpenBSD 5.7 seems not to correctly handle the
combinations of .struct and .previous used in unlzma.S, and ends up
complaining about an "attempt to allocate data in absolute section".
Work around this problem by explicitly resetting the section after the
data structure definitions.
Reported-by: Jiri B <jirib@devio.us>
Tested-by: Jiri B <jirib@devio.us>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Allow building PCI ROMs with device ID lists
PCI v3.0 supports a "device list" which allows the ROM to claim
support for multiple PCI device IDs (but only a single vendor ID).
Add support for building such ROMs by scanning the build target
element list and incorporating any device IDs into the ROM's device
list header. For example:
make bin/8086153a--8086153b.mrom
would build a ROM claiming support for both 8086:153a and 8086:153b.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Use the EFI_RNG_PROTOCOL as an entropy source if available
Entropy gathering via timer ticks is slow under UEFI (of the order of
20-30 seconds on some machines). Use the EFI_RNG_PROTOCOL if
available, to speed up the process of entropy gathering.
Note that some implementations (including EDK2) will fail if we
request fewer than 32 random bytes at a time, and that the RNG
protocol provides no guarantees about the amount of entropy provided
by a call to GetRNG(). We take the (hopefully pessimistic) view that
a 32-byte block returned by GetRNG() will contain at least the 1.3
bits of entropy claimed by min_entropy_per_sample().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Poll for TX completions only when there is an outstanding TX buffer
At least one NII implementation (in a Microsoft Surface tablet) seems
to fail to report the absence (sic) of TX completions properly. Work
around this by checking for TX completions only when we expect to see
one.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Poll media status only if advertised as supported
Some NII implementations will fail the GET_STATUS operation if we
request the media status. Fix by doing so only if GET_INIT_INFO
reported that media status is supported.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Allow autoboot device filter to be disabled
Our current behaviour when booting as a ROM is to autoboot only from
devices which are attached via the PCI bus:dev.fn address passed to
the ROM's initialisation vector.
Add a build configuration option AUTOBOOT_ROM_FILTER (enabled by
default) to control this behaviour. This allows for ROMs to be built
which will attempt to boot from any detected device, even if not
attached via the original PCI bus:dev.fn address. (This is
particularly useful when building combined EHCI/xHCI ROMs for USB
network boot, since the BIOS may request a boot via the EHCI
controller but the xHCI driver will reroute the root hub ports to the
xHCI controller.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In theory USB3 ports do not require a reset to enable the port.
Experimentation shows that this is sometimes required, particularly
when rerouting ports from EHCI to xHCI and switching speeds.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Rewrite parserom.pl to support multiple source files
Running util/parserom.pl on all source files (637) one by one takes
approximately 35 seconds because of the startup cost of each invocation.
With the utility rewritten to support multiple source files it now takes
approximately 1 second to scan all source files for ROM declarations.
The --exclude-driver and --exclude-driver-class options have been added,
making it possible to skip certain source files from being scanned at all.
In addition --debug option has been added to more easily trace progress.
Finally --help option was added to show usage information.
Signed-off-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Ensure drivers are disconnected when ExitBootServices() is called
We hook the UEFI ExitBootServices() event and use it to trigger a call
to shutdown_boot(). This does not automatically cause drivers to be
disconnected from their devices, since device enumeration is now
handled by the UEFI core rather than by iPXE. (Under the old and
dubiously compatible device model, iPXE used to perform its own device
enumeration and so the call to shutdown_boot() would indeed have
caused drivers to be disconnected.)
Fix by replicating parts of the dummy "EFI root device" from
efiprefix.c to efidrvprefix.c, so that the call to shutdown_boot()
will call efi_driver_disconnect_all().
Originally-fixed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-512/224 is almost identical to SHA-512, with differing initial
hash values and a truncated output length.
This implementation has been verified using the NIST SHA-512/224 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-512/256 is almost identical to SHA-512, with differing initial
hash values and a truncated output length.
This implementation has been verified using the NIST SHA-512/256 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-384 is almost identical to SHA-512, with differing initial hash
values and a truncated output length.
This implementation has been verified using the NIST SHA-384 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
SHA-224 is almost identical to SHA-256, with differing initial hash
values and a truncated output length.
This implementation has been verified using the NIST SHA-224 test
vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Update the digest self-tests to use okx(), and centralise concepts and
data shared between tests for multiple algorithms to reduce duplicated
code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown