[netdevice] Allow the hardware and link-layer addresses to differ in size
IPoIB has a 20-byte link-layer address, of which only eight bytes
represent anything relating to a "hardware address".
The PXE and EFI SNP APIs expect the permanent address to be the same
size as the link-layer address, so fill in the "permanent address"
field with the initial link layer address (as generated by
register_netdev() based upon the real hardware address).
[netdevice] Separate out the concept of hardware and link-layer addresses
The hardware address is an intrinsic property of the hardware, while
the link-layer address can be changed at runtime. This separation is
exposed via APIs such as PXE and EFI, but is currently elided by gPXE.
Expose the hardware and link-layer addresses as separate properties
within a net device. Drivers should now fill in hw_addr, which will
be used to initialise ll_addr at the time of calling
register_netdev().
[netdevice] Make ll_broadcast per-netdevice rather than per-ll_protocol
IPoIB has a link-layer broadcast address that varies according to the
partition key. We currently go through several contortions to pretend
that the link-layer address is a fixed constant; by making the
broadcast address a property of the network device rather than the
link-layer protocol it will be possible to simplify IPoIB's broadcast
handling.
[netdevice] Add netdev argument to link-layer push and pull handlers
In order to construct outgoing link-layer frames or parse incoming
ones properly, some protocols (such as 802.11) need more state than is
available in the existing variables passed to the link-layer protocol
handlers. To remedy this, add struct net_device *netdev as the first
argument to each of these functions, so that more information can be
fetched from the link layer-private part of the network device.
Updated all three call sites (netdevice.c, efi_snp.c, pxe_undi.c) and
both implementations (ethernet.c, ipoib.c) of ll_protocol to use the
new argument.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
[iobuf] Add iob_disown() and use it where it simplifies code
There are many functions that take ownership of the I/O buffer they
are passed as a parameter. The caller should not retain a pointer to
the I/O buffer. Use iob_disown() to automatically nullify the
caller's pointer, e.g.:
xfer_deliver_iob ( xfer, iob_disown ( iobuf ) );
This will ensure that iobuf is set to NULL for any code after the call
to xfer_deliver_iob().
iob_disown() is currently used only in places where it simplifies the
code, by avoiding an extra line explicitly setting the I/O buffer
pointer to NULL. It should ideally be used with each call to any
function that takes ownership of an I/O buffer. (The SSA
optimisations will ensure that use of iob_disown() gets optimised away
in cases where the caller makes no further use of the I/O buffer
pointer anyway.)
If gcc ever introduces an __attribute__((free)), indicating that use
of a function argument after a function call should generate a
warning, then we should use this to identify all applicable function
call sites, and add iob_disown() as necessary.
[efi] Expose both GUIDs for the EFI_NETWORK_INTERFACE_IDENTIFIER_PROTOCOL
At some point, it seems that someone decided to change the GUID for
the EFI_NETWORK_INTERFACE_IDENTIFIER_PROTOCOL. Current EFI builds
ignore the older GUID, older EFI builds ignore the newer GUID, so we
have to expose both.
[efi] Provide component name protocol and device path protocol interfaces
Include a minimal component name protocol so that the driver name
shows up as something other than "<UNKNOWN>" in the driver list, and a
device path protocol so that the network interface shows up as a
separate device in the device list, rather than being attached
directly to the PCI device.
Incidentally, the EFI component name protocol reaches new depths for
signal-to-noise ratio in program code. A typical instance within the
EFI development kit will use an additional 300 lines of code to
provide slightly less functionality than GNU gettext achieves with
three additional characters.
EFI_STATUS is defined as an INTN, which maps to UINT32 (i.e. unsigned
int) on i386 and UINT64 (i.e. unsigned long) on x86_64. This would
require a cast each time the error status is printed.
Add efi_strerror() to avoid this ickiness and simultaneously enable
prettier reporting of EFI status codes.
[i386] Change [u]int32_t to [unsigned] int, rather than [unsigned] long
This brings us in to line with Linux definitions, and also simplifies
adding x86_64 support since both platforms have 2-byte shorts, 4-byte
ints and 8-byte long longs.
[netdevice] Retain and report detailed error breakdowns
netdev_rx_err() and netdev_tx_complete_err() get passed the error
code, but currently use it only in debug messages.
Retain error numbers and frequencey counts for up to
NETDEV_MAX_UNIQUE_ERRORS (4) different errors for each of TX and RX.
This allows the "ifstat" command to report the reasons for TX/RX
errors in most cases, even in non-debug builds.