Allow the active timer (providing udelay() and currticks()) to be
selected at runtime based on probing during the INIT_EARLY stage of
initialisation.
TICKS_PER_SEC is now a fixed compile-time constant for all builds, and
is independent of the underlying clock tick rate. We choose the value
1024 to allow multiplications and divisions on seconds to be converted
to bit shifts.
TICKS_PER_MS is defined as 1, allowing multiplications and divisions
on milliseconds to be omitted entirely. The 2% inaccuracy in this
definition is negligible when using the standard BIOS timer (running
at around 18.2Hz).
TIMER_RDTSC now checks for a constant TSC before claiming to be a
usable timer. (This timer can be tested in KVM via the command-line
option "-cpu host,+invtsc".)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Limit MTU by hardware maximum frame length
Separate out the concept of "hardware maximum supported frame length"
and "configured link MTU", and limit the latter according to the
former.
In networks where the DHCP-supplied link MTU is inconsistent with the
hardware or driver capabilities (e.g. a network using jumbo frames),
this will result in iPXE advertising a TCP MSS consistent with a size
that can actually be received.
Note that the term "MTU" is typically used to refer to the maximum
length excluding the link-layer headers; we adopt this usage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a settings applicator to modify netdev->max_pkt_len in
response to changes to the "mtu" setting (DHCP option 26).
Note that as with MAC address changes, drivers are permitted to
completely ignore any changes in the MTU value. The net result will
be that iPXE effectively uses the smaller of either the hardware
default MTU or the software configured MTU.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This code largely inspired by tap.c. Allows for testing iPXE on real
NICs from within Linux. For example:
make bin-x86_64-linux/af_packet.linux
valgrind ./bin-x86_64-linux/af_packet.linux --net af_packet,if=eth3
Tested as x86_64 and i386 binary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Virtio 0.9 implementation was limited to the maximum virtqueue size of
MAX_QUEUE_NUM and the virtio-net driver would fail to initialize on hosts
exceeding this limit.
This commit lifts the restriction by allocating the queue memory based on
the actual queue size instead of using a fixed maximum. Note that virtio
1.0 still uses the MAX_QUEUE_NUM constant to cap the size (unfortunately
this functionality is not available in virtio 0.9).
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
vpm_find_vqs incorrectly accepted the host provided queue size with no
regard to iPXE's internal limitations. Virtio 1.0 makes it possible for
the driver to override the queue size to reduce memory requirements and
iPXE is a great use case for this feature.
Also removing the extra vq->vring.num assignment which is already
handled in vring_init.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Work around temporal anomaly encountered during ExitBootServices()
EFI provides no clean way for device drivers to shut down in
preparation for handover to a booted operating system. The platform
firmware simply doesn't bother to call the drivers' Stop() methods.
Instead, drivers must register an EVT_SIGNAL_EXIT_BOOT_SERVICES event
to be signalled when ExitBootServices() is called, and clean up
without any reference to the EFI driver model.
Unfortunately, all timers silently stop working when ExitBootServices()
is called. Even more unfortunately, and for no discernible reason,
this happens before any EVT_SIGNAL_EXIT_BOOT_SERVICES events are
signalled. The net effect of this entertaining design choice is that
any timeout loops on the shutdown path (e.g. for gracefully closing
outstanding TCP connections) may wait indefinitely.
There is no way to report failure from currticks(), since the API
lazily assumes that the host system continues to travel through time
in the usual direction. Work around EFI's violation of this
assumption by falling back to a simple free-running monotonic counter.
Debugged-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
AppleNetBoot.h is not taken from the EDK2 codebase and so cannot be
imported using include/ipxe/efi/import.pl. Mark as a native iPXE
header (by changing the include guard) to avoid breaking the import
process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Allow certificates to be marked as having been added explicitly
Allow certificates to be marked as having been added explicitly at run
time. Such certificates will not be discarded via the certificate
store cache discarder.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Enable IMAGE_PNG (but not IMAGE_PNM) by default, and drag in the
relevant objects only when image_pixbuf() is present in the binary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add PEM-encoded ASN.1 as an image format. We accept as PEM any image
containing a line starting with a "-----BEGIN" boundary marker.
We allow for PEM files containing multiple ASN.1 objects, such as a
certificate chain produced by concatenating individual certificate
files.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add DER-encoded ASN.1 as an image format. There is no fixed signature
for DER files. We treat an image as DER if it comprises a single
valid SEQUENCE object covering the entire length of the image.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Allow for parsing of partial ASN.1 cursors
Allow code to create a partial ASN.1 cursor containing only the type
and length bytes, so that asn1_start() may be used to determine the
length of a large ASN.1 blob without first allocating memory to hold
the entire blob.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Windows drivers for VMBus devices are enumerated using the
instance UUID rather than the channel number. Include the instance
UUID within the iPXE device name to allow an iPXE network device to be
more easily associated with the corresponding Windows network device
when debugging.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Select the IPv6 source address and corresponding router (if any) using
a very simplified version of the algorithm from RFC6724:
- Ignore any source address that has a smaller scope than the
destination address. For example, do not use a link-local source
address when sending to a global destination address.
- If we have a source address which is on the same link as the
destination address, then use that source address.
- If we are left with multiple possible source addresses, then choose
the address with the smallest scope. For example, if we are sending
to a site-local destination address and we have both a global source
address and a site-local source address, then use the site-local
source address.
- If we are still left with multiple possible source addresses, then
choose the address with the longest matching prefix.
For the purposes of this algorithm, we treat RFC4193 Unique Local
Addresses as having organisation-local scope. Since we use only
link-local scope for our multicast transmissions, this approximation
should remain valid in all practical situations.
Originally-implemented-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv6] Create routing table based on IPv6 settings
Use the IPv6 settings to construct the routing table, in a matter
analogous to the construction of the IPv4 routing table.
This allows for manual assignment of IPv6 addresses via e.g.
set net0/ip6 2001:ba8:0:1d4::6950:5845
set net0/len6 64
set net0/gateway6 fe80::226:bff:fedd:d3c0
The prefix length ("len6") may be omitted, in which case a default
prefix length of 64 will be assumed.
Multiple IPv6 addresses may be assigned manually by implicitly
creating child settings blocks. For example:
set net0/ip6 2001:ba8:0:1d4::6950:5845
set net0.ula/ip6 fda4:2496:e992::6950:5845
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv6] Match user expectations for IPv6 settings priorities
A reasonable user expectation is that ${net0/ip6} should show the
"highest-priority" of the IPv6 addresses, even when multiple IPv6
addresses are active. The expected order of priority is likely to be
manually-assigned addresses first, then stateful DHCPv6 addresses,
then SLAAC addresses, and lastly link-local addresses.
Using ${priority} to enforce an ordering is undesirable since that
would affect the priority assigned to each of the net<N> blocks as a
whole, so use the sibling ordering capability instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[settings] Allow settings blocks to specify a sibling ordering
Allow settings blocks to provide an explicit default ordering between
siblings, with lower precedence than the existing ${priority} setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Originally-implemented-by: Hannes Reinecke <hare@suse.de>
Originally-implemented-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose the IPv6 address (or prefix) as ${ip6}, the prefix length as
${len6}, and the router address as ${gateway6}.
Originally-implemented-by: Hannes Reinecke <hare@suse.de>
Originally-implemented-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The settings scope ipv6_scope refers specifically to IPv6 settings
that have a corresponding DHCPv6 option. Rename to dhcpv6_scope to
more accurately reflect this purpose.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Install the HII config access protocol on a child of the SNP handle
In edk2, there are several drivers that associate HII forms (and
corresponding config access protocol instances) with each individual
network device. (In this context, "network device" means the EFI
handle on which the SNP protocol is installed, and on which the device
path ending with the MAC() node is installed also.) Such edk2 drivers
are, for example: Ip4Dxe, HttpBootDxe, VlanConfigDxe.
In UEFI, any given handle can carry at most one instance of a specific
protocol (see e.g. the specification of the InstallProtocolInterface()
boot service). This implies that the class of drivers mentioned above
can't install their EFI_HII_CONFIG_ACCESS_PROTOCOL instances on the
SNP handle directly -- they would conflict with each other.
Accordingly, each of those edk2 drivers creates a "private" child
handle under the SNP handle, and installs its config access protocol
(and corresponding HII package list) on its child handle.
The device path for the child handle is traditionally derived by
appending a Hardware Vendor Device Path node after the MAC() node.
The VenHw() nodes in question consist of a GUID (by definition), and
no trailing data (by choice). The purpose of these VenHw() nodes is
only that all the child nodes can be uniquely identified by device
path.
At the moment iPXE does not follow this pattern. It doesn't run into
a conflict when it installs its EFI_HII_CONFIG_ACCESS_PROTOCOL
directly on the SNP handle, but that's only because iPXE is the sole
driver not following the pattern. This behavior seems risky (one
might call it a "latent bug"); better align iPXE with the edk2 custom.
Cc: Michael Brown <mcb30@ipxe.org>
Cc: Gary Lin <glin@suse.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Ref: http://thread.gmane.org/gmane.comp.bios.edk2.devel/13494/focus=13532
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ladi Prosek <lprosek@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[profile] Allow profiling to be globally enabled or disabled
As with assertions, profiling is enabled for objects built with any
debug level (including an explicit debug level of zero).
Allow profiling to be globally enabled or disabled by adding PROFILE=1
or PROFILE=0 respectively to the build command line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[libc] Allow assertions to be globally enabled or disabled
Assertions are enabled for objects built with any debug level
(including an explicit debug level of zero). It is sometimes useful
to be able to enable assertions across all objects; this currently
requires manually hacking include/assert.h.
Allow assertions to be globally enabled by adding ASSERT=1 to the
build command line. For example:
make bin/8086100e.mrom ASSERT=1
Similarly, allow assertions to be globally disabled by adding ASSERT=0
to the build command line. If no ASSERT=... is specified on the
build command line, then only objects mentioned in DEBUG=... will have
assertions enabled (as is currently the case).
Note than globally enabling assertions imposes a relatively heavy
runtime penalty, primarily due to the various sanity checks performed
by list_add(), list_for_each_entry(), etc.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[debug] Allow debug messages to be initially disabled at runtime
Extend the DEBUG=... syntax to allow debug messages to be compiled in
but disabled by default. For example:
make bin/undionly.kpxe DEBUG=netdevice:3:1
would compile in the messages as for DEBUG=netdevice:3, but would set
the debug level mask so that only the DEBUG=netdevice:1 messages would
be displayed.
This allows for external code to selectively enable the additional
debug messages at runtime, without being overwhelmed by unwanted
initial noise. For example, a developer of a new protocol may want to
temporarily enable tracing of all packets received: this can be done
by building with DEBUG=netdevice:3:1 and using
// temporarily enable per-packet messages
DBG_ENABLE_OBJECT ( netdevice, DBGLVL_EXTRA );
...
// disable per-packet messages
DBG_DISABLE_OBJECT ( netdevice, DBGLVL_EXTRA );
Note that unlike the usual DBG_ENABLE() and DBG_DISABLE() macros,
DBG_ENABLE_OBJECT() and DBG_DISABLE_OBJECT() will not be removed via
dead code elimination if debugging is disabled in the specified
object. In particular, this means that using either of these macros
will always result in a symbol reference to the specified object.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[debug] Allow per-object runtime enabling/disabling of debug messages
The DBG_ENABLE() and DBG_DISABLE() macros currently affect the debug
level of all objects that were built with debugging enabled. This is
undesirable, since it is common to use different debug levels in each
object.
Make the debug level mask a per-object variable. DBG_ENABLE() and
DBG_DISABLE() now control only the debug level for the containing
object (which is consistent with the intended usage across the
existing codebase). DBG_ENABLE_OBJECT() and DBG_DISABLE_OBJECT() may
be used to control the debug level for a specified object. For
example:
// Enable DBG() messages from tcpip.c
DBG_ENABLE_OBJECT ( tcpip, DBGLVL_LOG );
Note that the existence of debug messages continues to be gated by the
DEBUG=... list specified on the build command line. If an object was
built without the relevant debug level, then DBG_ENABLE_OBJECT() will
have no effect on that object at runtime (other than to explicitly
drag in the object via a symbol reference).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcp] Automatically generate vendor class identifier string
The vendor class identifier strings in DHCP_ARCH_VENDOR_CLASS_ID are
out of sync with the (correct) client architecture values in
DHCP_ARCH_CLIENT_ARCHITECTURE.
Fix by removing all definitions of DHCP_ARCH_VENDOR_CLASS_ID, and
instead generating the vendor class identifier string automatically
based on DHCP_ARCH_CLIENT_ARCHITECTURE and DHCP_ARCH_CLIENT_NDI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcpv6] Include vendor class identifier option in DHCPv6 requests
RFC3315 defines DHCPv6 option 16 (vendor class identifier) but does
not define any direct relationship with the roughly equivalent DHCPv4
option 60.
The PXE specification predates IPv6, and the UEFI specification is
expectedly vague on the subject. Examination of the reference EDK2
codebase suggests that the DHCPv6 vendor class identifier will be
formatted in accordance with RFC3315, using a single vendor-class-data
item in which the opaque-data field is the string as would appear in
DHCPv4 option 60.
RFC3315 requires the vendor class identifier to specify an IANA
enterprise number, as a way of disambiguating the vendor-class-data
namespace. The EDK2 code uses the value 343, described as:
// TODO: IANA TBD: temporarily using Intel's
Since this "TODO" has been present since at least 2010, it is probably
safe to assume that it has now become a de facto standard.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[dhcpv6] Include RFC5970 client architecture options in DHCPv6 requests
RFC5970 defines DHCPv6 options 61 (client system architecture type)
and 62 (client network interface identifier), with contents equivalent
to DHCPv4 options 93 and 94 respectively.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some of the regions may end up being unmapped, either because they are
optional or because the attempt to map them has failed. Region types
starting at 0 didn't make it easy to test for this condition.
This commit bumps all valid region types up by 1 with 0 having the
implicit 'unmapped' meaning.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[time] Allow system clock to be adjusted at runtime
Provide a mechanism to allow an arbitrary adjustment to be applied to
all subsequent calls to time().
Note that the underlying clock source (e.g. the RTC clock) will not be
changed; only the time as reported within iPXE will be affected.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown