[efi] Do not raise TPL within EFI_DRIVER_BINDING_PROTOCOL.Supported()
When booting some versions of the UEFI shell, our driver binding
protocol's Supported() entry point is called at TPL_NOTIFY for no
discernible reason. Attempting to raise to TPL_CALLBACK triggers an
immediate assertion failure in the firmware.
Since our Supported() method can run at any TPL, fix by simply not
attempting to raise the TPL within this method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Inhibit our driver Start() method during disconnection attempts
Some HP BIOSes (observed with a Z840) seem to attempt to connect our
drivers in the middle of our call to DisconnectController(). The
precise chain of events is unclear, but the symptom is that we see
several calls to our Supported() and Start() methods, followed by a
system lock-up.
Work around this dubious BIOS behaviour by explicitly failing calls to
our Start() method while we are in the middle of attempting to
disconnect drivers.
Reported-by: Jordan Wright <jordan.m.wright@disney.com>
Debugged-by: Adrian Lucrèce Céleste <adrianlucrececeleste@airmail.cc>
Debugged-by: Christian Nilsson <nikize@gmail.com>
Tested-by: Jordan Wright <jordan.m.wright@disney.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Continue to connect remaining handles after connection errors
Some UEFI BIOSes will deliberately break the implementation of
ConnectController() to return errors for devices that have been
"disabled" via the BIOS setup screen. (As an added bonus, such BIOSes
may return garbage EFI_STATUS values such as 0xff.)
Work around these broken UEFI BIOSes by ignoring failures and
continuing to attempt to connect any remaining handles.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Avoid infinite loops when asked to stop non-existent devices
Calling EDK2's OpenProtocol() with attributes BY_DRIVER|EXCLUSIVE will
call DisconnectController() in a loop to attempt to dislodge any
existing openers with attributes BY_DRIVER. The loop will continue
indefinitely until either no such openers remain, or until
DisconnectController() returns an error.
If our driver binding protocol's Stop() method is ever called to
disconnect a device that we are not in fact driving, then return
EFI_DEVICE_ERROR rather than EFI_SUCCESS, in order to break this
potentially infinite loop.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Remove raw EFI_HANDLE values from debug messages
The raw EFI_HANDLE value is almost never useful to know, and simply
adds noise to the already verbose debug messages. Improve the
legibility of debug messages by using only the name generated by
efi_handle_name().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Open device path protocol only at point of use
Some EFI 1.10 systems (observed on an Apple iMac) do not allow us to
open the device path protocol with an attribute of
EFI_OPEN_PROTOCOL_BY_DRIVER and so we cannot maintain a safe,
long-lived pointer to the device path. Work around this by instead
opening the device path protocol with an attribute of
EFI_OPEN_PROTOCOL_GET_PROTOCOL whenever we need to use it.
Debugged-by: Curtis Larsen <larsen@dixie.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Dump existing openers when we are unable to open a protocol
Dump the existing openers of a protocol whenever we are unable to open
a protocol using attributes of BY_DEVICE, EXCLUSIVE, or
BY_CHILD_CONTROLLER.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a single instance of EFI_DRIVER_BINDING_PROTOCOL (attached to
our image handle); this matches the expectations scattered throughout
the EFI specification.
Open the underlying hardware device using EFI_OPEN_PROTOCOL_BY_DRIVER
and EFI_OPEN_PROTOCOL_EXCLUSIVE, to prevent other drivers from
attaching to the same device.
Do not automatically connect to devices when being loaded as a driver;
leave this task to the platform firmware (or to the user, if loading
directly from the EFI shell).
When running as an application, forcibly disconnect any existing
drivers from devices that we want to control, and reconnect them on
exit.
Provide a meaningful driver version number (based on the build
timestamp), to allow platform firmware to automatically load newer
versions of iPXE drivers if multiple drivers are present.
Include device paths within debug messages where possible, to aid in
debugging.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Expose build timestamp, build name, and product names
Expose the build timestamp (measured in seconds since the Epoch) and
the build name (e.g. "rtl8139.rom" or "ipxe.efi"), and provide the
product name and product short name in a single centralised location.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Exploit the redefinition of iPXE error codes to include a "platform
error code" to allow for meaningful conversion of EFI_STATUS values to
iPXE errors and vice versa.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Delegate to child device's EFI_COMPONENT_NAME2_PROTOCOL, if present
EFI's device naming model requires drivers to provide names for child
devices. Allow the driver's GetControllerName() method to delegate to
an instance of EFI_COMPONENT_NAME2_PROTOCOL installed on the child
device itself (if present); this allows the SNP device to expose its
own device name via the PCI driver's GetControllerName() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFI performs its own PCI bus enumeration. Respect this, and start
controlling devices only when instructed to do so by EFI.
As a side benefit, we should now correctly create multiple SNP
instances for multi-port devices.
This should also fix the problem of failing to enumerate devices
because the PCI bridges have not yet been enabled at the time the iPXE
driver is loaded.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown