[usb] Use port->disconnected to check for disconnected devices
The usb_message() and usb_stream() functions currently check for
port->speed==USB_SPEED_NONE to determine whether or not a device has
been unplugged. This test will give a false negative result if a new
device has been plugged in before the hotplug mechanism has finished
handling the removal of the old device.
Fix by checking instead the port->disconnected flag, which is now
cleared only after completing the removal of the old device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smsc95xx] Add driver for SMSC/Microchip LAN95xx USB Ethernet NICs
Tested using QEMU and usbredir to expose the LAN9512 chip present on a
Raspberry Pi.
There is a known issue with the LAN9512: an extra two bytes are
appended to every transmitted packet. These two bytes comprise:
{ 0x00, 0x08 } if packet length == 0 (mod 8)
{ CRC[0], 0x00 } if packet length == 7 (mod 8)
{ CRC[0], CRC[1] } otherwise
The extra bytes are appended whether the Ethernet CRC is generated
manually or added automatically by the hardware. The issue occurs
with the Linux kernel driver as well as the iPXE driver. It appears
to be an undocumented hardware errata.
TCP/IP traffic is not affected, since the IP header length field
causes the extraneous bytes to be discarded by the receiver. However,
protocols that rely on the length of the Ethernet frame (such as FCoE
or iPXE's "lotest" protocol) will be unusable on this hardware.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some models (notably ICH), the PHY reset mechanism appears to be
broken. In particular, the PHY_CTRL register will be correctly loaded
from NVM but the values will not be propagated to the "OEM bits" PHY
register. This typically has the effect of dropping the link speed to
10Mbps.
Since the original version of this driver in commit 945e428 ("[intel]
Replace driver for Intel Gigabit NICs"), we have always worked around
this problem by skipping the PHY reset if the link is already up.
Enhance this workaround by explicitly checking for known-broken PCI
IDs.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Make the class ID a property of the USB driver (rather than a property
of the USB device ID), and allow USB drivers to specify a wildcard ID
for any of the three component IDs (class, subclass, or protocol).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Select preferred USB device configuration based on driver score
Generate a score for each possible USB device configuration based on
the available driver support, and select the configuration with the
highest score. This will allow us to prefer ECM over RNDIS (for
devices which support both) and will allow us to meaningfully select a
configuration even when we have drivers available for all functions
(e.g. when exposing unused functions via EFI_USB_IO_PROTOCOL).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The decision on whether or not a zero-length packet needs to be
transmitted is independent of the host controller and belongs in the
USB core.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Add a USB host controller driver based on EFI_USB_IO_PROTOCOL
Allow iPXE to coexist with other USB device drivers, by attaching to
the EFI_USB_IO_PROTOCOL instances provided by the UEFI platform
firmware.
The EFI_USB_IO_PROTOCOL is an unsurprisingly badly designed
abstraction of a USB device. The poor design choices intrinsic in the
UEFI specification prevent efficient operation as a network device,
with the result that devices operated using the EFI_USB_IO_PROTOCOL
operate approximately two orders of magnitude slower than devices
operated using our native EHCI or xHCI host controller drivers.
Since the performance is so abysmally slow, and since the underlying
problems are due to fundamental architectural mistakes in the UEFI
specification, support for the EFI_USB_IO_PROTOCOL host controller
driver is left as disabled by default. Users are advised to use the
native iPXE host controller drivers instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Remove raw EFI_HANDLE values from debug messages
The raw EFI_HANDLE value is almost never useful to know, and simply
adds noise to the already verbose debug messages. Improve the
legibility of debug messages by using only the name generated by
efi_handle_name().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipoib] Fix a race when chain-loading undionly.kpxe in IPoIB
The Infiniband link status change callback ipoib_link_state_changed()
may be called while the IPoIB device is closed, in which case there
will not be an IPoIB queue pair to be joined to the IPv4 broadcast
group. This leads to NULL pointer dereferences in ib_mcast_attach()
and ib_mcast_detach().
Fix by not attempting to join (or leave) the broadcast group unless we
actually have an IPoIB queue pair.
Signed-off-by: Wissam Shoukair <wissams@mellanox.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Multicast MAC addresses will never have REMAC cache entries, and the
corresponding multicast IPoIB MAC address cannot be obtained simply by
issuing an ARP request.
For the trivial volume of multicast packets that we expect to send in
any realistic scenario, the simplest solution is to send them as
broadcasts instead.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipoib] Attempt to generate ARPs as needed to repopulate REMAC cache
The only way to map an eIPoIB MAC address (REMAC) to an IPoIB MAC
address is to intercept an incoming ARP request or reply.
If we do not have an REMAC cache entry for a particular destination
MAC address, then we cannot transmit the packet. This can arise in at
least two situations:
- An external program (e.g. a PXE NBP using the UNDI API) may attempt
to transmit to a destination MAC address that has been obtained by
some method other than ARP.
- Memory pressure may have caused REMAC cache entries to be
discarded. This is fairly likely on a busy network, since REMAC
cache entries are created for all received (broadcast) ARP
requests. (We can't sensibly avoid creating these cache entries,
since they are required in order to send an ARP reply, and when we
are being used via the UNDI API we may have no knowledge of which
IP addresses are "ours".)
Attempt to ameliorate the situation by generating a semi-spurious ARP
request whenever we find a missing REMAC cache entry. This will
hopefully trigger an ARP reply, which would then provide us with the
information required to populate the REMAC cache.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As with the neighbour cache, discarding an REMAC cache entry is
potentially very disruptive.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[xhci] Ignore invalid protocol speed ID values on Intel Skylake platforms
Some Intel Skylake platforms (observed on a prototype Lenovo ThinkPad)
report the list of available USB3 protocol speed ID values as {1,2,3}
but then report a port's speed using ID value 4.
The value 4 happens to be the default value for SuperSpeed (when no
protocol speed ID value list is explicitly defined), and the hardware
seems to function correctly if we simply ignore its protocol speed ID
table and assume that it uses the default values.
Fix by adding a "broken PSI values" quirk for this controller.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[xhci] Fix comparison of signed and unsigned integers
gcc 4.8.2 fails to report this erroneous comparison unless assertions
are enabled.
Reported-by: Mary-Ann Johnson <MaryAnn.Johnson@displaylink.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The xHCI slot ID is one-based, not zero-based. Fix the length of the
xhci->slot[] array to account for this, and add assertions to check
that the hardware returns a valid slot ID in response to the Enable
Slot command.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Fix operation when physical function has jumbo frames enabled
When jumbo frames are enabled, the Linux ixgbe physical function
driver will disable the virtual function's receive datapath by
default, and will enable it only if the virtual function negotiates
API version 1.1 (or higher) and explicitly selects an MTU.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Add support for mailbox used by virtual functions
Virtual functions use a mailbox to communicate with the physical
function driver: this covers functionality such as obtaining the MAC
address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Allow for the use of advanced TX descriptors
Intel virtual function NICs almost work with the use of "legacy"
transmit and receive descriptors (which are backwards compatible right
back to the original Intel Gigabit NICs).
Unfortunately the "TX switching" feature (which allows for VM<->VM
traffic to be looped back within the NIC itself) does not work when a
legacy TX descriptor is used: the packet is instead sent onto the
wire.
Fix by allowing for the use of an "advanced" TX descriptor (containing
exactly the same information as is found in the "legacy" descriptor).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Always clear recorded disconnections after performing hotplug actions
The recorded disconnections (in port->disconnected) will currently be
left uncleared if usb_attached() returns an error (e.g. because there
are no drivers for a particular USB device). This is incorrect
behaviour: the disconnection has been handled and the record should be
cleared until the next physical disconnection is detected (via the CSC
bit).
The problem is masked for EHCI, UHCI, and USB hubs, since these will
report a changed port (via usb_port_changed()) only when the
underlying hardware reports a change. xHCI will call
usb_port_changed() in response to any port status event, at which
point the stale value of port->disconnected will be erroneously acted
upon. This can lead to an endless loop of repeatedly enumerating the
same device when a driverless device is attached to an xHCI root hub
port.
Fix by unconditionally clearing port->disconnected in usb_hotplugged().
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Do not call usb_hotplug() when registering a new hub
The action of registering a new hub can itself happen in only two
ways: either a new USB hub has been created (in which case we are
already inside a call to usb_hotplug()), or a new root hub has been
created.
In the former case, we do not need to issue a further call to
usb_hotplug(), since the hub's ports will all be marked as changed and
so will be handled after the return from register_usb_hub() anyway.
Calling usb_hotplug() within register_usb_hub() leads to a confusing
order of events, such as:
- root hub port 1 detects a change
- root hub port 2 detects a change
- usb_hotplug() is called
- root hub port 1 finds a USB hub
- usb_hotplug() is called
- this inner call to usb_hotplug() handles root hub port 2
Fix by calling usb_hotplug() only from usb_step() and from
register_usb_bus(). This avoids recursive calls to usb_hotplug() and
ensures that devices are enumerated in the order of detection.
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When USB network card drivers are used, the BIOS' legacy USB
capability is necessarily disabled since there is no way to share the
host controller between the BIOS and iPXE. This currently results in
USB keyboards becoming non-functional in USB-enabled builds of iPXE.
Fix by adding basic support for USB keyboards, enabled by default in
iPXE builds which include USB support.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown