[build] Fix use of inline assembly on GCC 8 ARM64 builds
Commit 1a7746603 ("[build] Fix use of inline assembly on GCC 4.8 ARM64
builds") switched from using "%c0" to "%a0" in order to avoid an
"invalid operand prefix" error on the ARM64 version of GCC 4.8.
It appears that the ARM64 version of GCC 8 now produces an "invalid
address mode" error for the "%a0" form, but is happy with the original
"%c0" form.
Switch back to using the "%c0" form, on the assumption that the
requirement for "%a0" was a temporary aberration.
Originally-fixed-by: John L. Jolly <jjolly@suse.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[vlan] Provide vlan_netdev_rx() and vlan_netdev_rx_err()
The Hermon driver uses vlan_find() to identify the appropriate VLAN
device for packets that are received with the VLAN tag already
stripped out by the hardware. Generalise this capability and expose
it for use by other network card drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel 40 Gigabit Ethernet virtual functions support only MSI-X
interrupts, and will write back completed interrupt descriptors only
when the device attempts to raise an interrupt (or when a complete
cacheline of receive descriptors has been completed).
We cannot actually use MSI-X interrupts within iPXE, since we never
have ownership of the APIC. However, an MSI-X interrupt is
fundamentally just a DMA write of a single dword to an arbitrary
address. We can therefore configure the device to "raise" an
interrupt by writing a meaningless value to an otherwise unused memory
location: this is sufficient to trigger the receive descriptor
writeback logic.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ocsp] Accept response certID with missing hashAlgorithm parameters
One of the design goals of ASN.1 DER is to provide a canonical
serialization of a data structure, thereby allowing for equality of
values to be tested by simply comparing the serialized bytes.
Some OCSP servers will modify the request certID to omit the optional
(and null) "parameters" portion of the hashAlgorithm. This is
arguably legal but breaks the ability to perform a straightforward
bitwise comparison on the entire certID field between request and
response.
Fix by comparing the OID-identified hashAlgorithm separately from the
remaining certID fields.
Originally-fixed-by: Thilo Fromm <Thilo@kinvolk.io>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Record the session ID (if any) provided by the server and attempt to
reuse it for any concurrent connections to the same server.
If multiple connections are initiated concurrently (e.g. when using
PeerDist) then defer sending the ClientHello for all but the first
connection, to allow time for the first connection to potentially
obtain a session ID (and thereby speed up the negotiation for all
remaining connections).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On a Dell OptiPlex 7010, calling DisconnectController() on the LOM
device handle will lock up the system. Debugging shows that execution
is trapped in an infinite loop that is somehow trying to reconnect
drivers (without going via ConnectController()).
The problem can be reproduced in the UEFI shell with no iPXE code
present, by using the "disconnect" command. Experimentation shows
that the only fix is to unload (rather than just disconnect) the
"Ip4ConfigDxe" driver.
Add the concept of a blacklist of UEFI drivers that will be
automatically unloaded when iPXE runs as an application, and add the
Dell Ip4ConfigDxe driver to this blacklist.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the function mii_find() in order to locate the PHY address.
Signed-off-by: Sylvie Barlow <sylvie.c.barlow@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[mii] Separate concepts of MII interface and MII device
We currently have no generic concept of a PHY address, since all
existing implementations simply hardcode the PHY address within the
MII access methods.
A bit-bashing MII interface will need to be provided with an explicit
PHY address in order to generate the correct waveform. Allow for this
by separating out the concept of a MII device (i.e. a specific PHY
address attached to a particular MII interface).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In TLS terminology a session conceptually spans multiple individual
connections, and essentially represents the stored cryptographic state
(master secret and cipher suite) required to establish communication
without going through the certificate and key exchange handshakes.
Rename tls_session to tls_connection in order to make the name
tls_session available to represent the session state.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[rng] Use fixed-point calculations for min-entropy quantities
We currently perform various min-entropy calculations using build-time
floating-point arithmetic. No floating-point code ends up in the
final binary, since the results are eventually converted to integers
and asserted to be compile-time constants.
Though this mechanism is undoubtedly cute, it inhibits us from using
"-mno-sse" to prevent the use of SSE registers by the compiler.
Fix by using fixed-point arithmetic instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[time] Add support for the ACPI power management timer
Allow the ACPI power management timer to be used if enabled via
TIMER_ACPI in config/timer.h. This provides an alternative timer on
systems where the standard 8254 PIT is unavailable or unreliable.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some CAs provide non-functional OCSP servers, and some clients are
forced to operate on networks without access to the OCSP servers.
Allow the user to explicitly disable the use of OCSP checks by
undefining OCSP_CHECK in config/crypto.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[lacp] Mark link as blocked if partner is not yet up and running
Mark the link as blocked if the LACP partner is not reporting itself
as being in sync, collecting, and distributing.
This matches the behaviour for STP: we mark the link as blocked if we
detect that the switch is actively blocking traffic, in order to
extend the DHCP discovery period and so prevent boot failures on
switches that take an excessively long time to enable ports.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[http] Handle parsing of WWW-Authenticate header within authentication scheme
Allow individual authentication schemes to parse WWW-Authenticate
headers that do not comply with RFC2617.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[peerdist] Gather and report peer statistics during download
Record and report the number of peers (calculated as the maximum
number of peers discovered for a block's segment at the time that the
block download is complete), and the percentage of blocks retrieved
from peers rather than from the origin server.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Do not steal ownership from the Gen 2 UEFI firmware
We must not steal ownership from the Gen 2 UEFI firmware, since doing
so will cause an immediate system crash (most likely in the form of a
reboot).
This problem was masked before commit a0f6e75 ("[hyperv] Do not fail
if guest OS ID MSR is already set"), since prior to that commit we
would always fail if we found any non-zero guest OS identity. We now
accept a non-zero previous guest OS identity in order to allow for
situations such as chainloading from iPXE to another iPXE, and as a
prerequisite for commit b91cc98 ("[hyperv] Cope with Windows Server
2016 enlightenments").
A proper fix would be to reverse engineer the UEFI protocols exposed
within the Hyper-V Gen 2 firmware and use these to bind to the VMBus
device representing the network connection, (with the native Hyper-V
driver moved to become a BIOS-only feature).
As an interim solution, fail to initialise the native Hyper-V driver
if we detect the guest OS identity known to be used by the Gen 2 UEFI
firmware. This will cause the standard all-drivers build (ipxe.efi)
to fall back to using the SNP driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Fix use of inline assembly on GCC 4.8 ARM64 builds
The inline assembly used in include/errno.h to generate the einfo
blocks requires the ability to generate an immediate constant with no
immediate-value prefix (such as the dollar sign for x86 assembly).
We currently achieve this via the undocumented "%c0" form of operand.
This causes an "invalid operand prefix" error on GCC 4.8 for ARM64
builds.
Fix by switching to the equally undocumented "%a0" form of operand,
which appears to work correctly on all tested versions of GCC.
Reported-by: Benjamin S. Allen <bsallen@alcf.anl.gov>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since we don't enable IOMMU at all, we can then simply enable the
IOMMU support by claiming the support of VIRITO_F_IOMMU_PLATFORM.
This fixes booting failure when iommu_platform is set from qemu cli.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smscusb] Abstract out common SMSC USB device functionality
The smsc75xx and smsc95xx drivers include a substantial amount of
identical functionality, varying only in the base address of register
sets. Abstract out this common functionality to allow code to be
shared between the drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support renegotiation with servers supporting RFC5746. This allows
for the use of per-directory client certificates.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[usb] Use non-zero language ID to retrieve strings
We currently use a zero language ID to retrieve strings such as the
ECM/NCM MAC address. This works on most hardware devices, but is
known to fail on some software emulated CDC-NCM devices.
Fix by using the first supported language ID, falling back to English
(0x0409) if any error occurs when fetching the list of supported
languages. This matches the behaviour of the Linux kernel.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Provide asn1_built() to construct a cursor from a builder
Our ASN.1 parsing code uses a struct asn1_cursor, while the object
construction code uses a struct asn1_builder. These structures are
identical apart from the const modifier applied to the data pointer in
struct asn1_cursor.
Provide asn1_built() to safely typecast a struct asn1_builder to a
struct asn1_cursor, allowing constructed objects to be passed to
functions expecting a struct asn1_cursor.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow values to be read from ACPI tables using the syntax
${acpi/<signature>.<index>.0.<offset>.<length>}
where <signature> is the ACPI table signature as a 32-bit hexadecimal
number (e.g. 0x41504093 for the 'APIC' signature on the MADT), <index>
is the index into the array of tables matching this signature,
<offset> is the byte offset within the table, and <length> is the
field length in bytes.
Numeric values are returned in reverse byte order, since ACPI numeric
values are usually little-endian.
For example:
${acpi/0x41504943.0.0.0.0} - entire MADT table in raw hex
${acpi/0x41504943.0.0.0x0a.6:string} - MADT table OEM ID
${acpi/0x41504943.0.0.0x24.4:uint32} - local APIC address
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown