[refcnt] Check reference validity on each use of ref_get() and ref_put()
Check that the reference count is valid (i.e. non-negative) on each
call to ref_get() and ref_put(), using an assert() at the point of
use.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There are several points in the iPXE codebase where
list_for_each_entry() is (ab)used to extract only the first entry from
a list. Add a macro list_first_entry() to make this code easier to
read.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For some install-to-SAN scenarios, the OS needs to be able to reboot
to reread the partition table. On this second boot attempt, the SAN
disk will not be empty and so iPXE will attempt to boot from it,
rather than falling back to the OS' installation media.
Work around this problem by introducing the "skip-san-boot" option,
similar in spirit to "keep-san".
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[scsi] Wait for a successful TEST UNIT READY command
Some SCSI targets (observed with an EMC CLARiiON Fibre Channel target)
will not respond to commands correctly until a TEST UNIT READY has
been issued. In particular, a READ CAPACITY (10) command will return
with a success status, but no capacity data.
Fix by issuing a TEST UNIT READY command automatically, and delaying
further SCSI commands until the TEST UNIT READY has succeeded.
Reported-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[iscsi] Ensure ISID is consistent within an iSCSI session
Commit 5f4ab0d ("[iscsi] Randomise a portion of the ISID to force new
session instantiation") introduced a regression by randomising the
ISID on each call to iscsi_start_login(), which may be called more
than once per connection, rather than on each call to
iscsi_open_connection(), which is guaranteed to be called only once
per connection. This is incorrect behaviour that causes our
connection to be rejected by some iSCSI targets (observed with a
COMSTAR target under OpenSolaris).
Fix by generating the ISID in iscsi_open_connection(), and storing the
randomised ISID as part of the session state.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Pass both link-layer addresses in net_tx() and net_rx()
FCoE requires the use of fabric-provided MAC addresses, which breaks
the assumption that the net device's MAC address is implicitly the
source address for net_tx() and the (unicast) destination address for
net_rx().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[libc] Ensure that error numbers from EUNIQ() have the correct type
Error numbers are signed ints. EUNIQ() should not allow implicit type
promotion based on the supplied error diambiguator, because this
causes problems with statements such as
rc = ( condition ? -EUNIQ ( EBASE, disambiguator ) : -EBASE );
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[int13] Add infrastructure to support EDD version 4.0
Support the extensions mandated by EDD 4.0, including:
o the ability to specify a flat physical address in a disk address
packet,
o the ability to specify a sector count greater than 127 in a disk
address packet,
o support for all functions within the Fixed Disk Access and EDD
Support subsets,
o the ability to describe a device using EDD Device Path Information.
This implementation is based on draft revision 3 of the EDD 4.0
specification, with reference to the EDD 3.0 specification. It is
possible that this implementation may need to change in order to
conform to the final published EDD 4.0 specification.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[fc] Allow FLOGI response to be sent to newly-assigned peer port ID
The response to a received FLOGI should probably be sent to the peer
port ID assigned as a result of the WWPN comparison.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[infiniband] Add node GUID as distinct from the first port GUID
iPXE currently uses the first port's port GUID as the node GUID,
rather than using the (possibly distinct) real node GUID. This can
confuse opensm during the handover to a loaded OS: it thinks the port
already belongs to a different node and so discards our port
information with a warning message about duplicate ports. Everything
is picked up correctly on the second subnet sweep, after opensm has
established that the "old" node no longer exists, but this can delay
link-up unnecessarily by several seconds.
Fix by using the real node GUID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[infiniband] Always call ib_link_state_changed() in ib_smc_update()
ib_smc_update() potentially updates the Infiniband port state, and so
should almost always be followed by a call to ib_link_state_changed().
The one exception is the call made to ib_smc_update() before the
device is registered.
Fix by removing explicit calls to ib_link_state_changed() from drivers
using ib_smc_update(), including a call to ib_link_state_changed()
within ib_smc_update(), and creating a separate ib_smc_init() for use
prior to device registration.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[scsi] Include sense key within error number reported to user
The sense key gives a first idea of what the problem might be, and so
is potentially useful in diagnosing problems in a non-debug build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Fibre Channel Protocol provides a mechanism for transporting SCSI
commands via a Fibre Channel fabric.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for Fibre Channel ports, peers, and upper-layer protocols,
and for Fibre Channel extended link services.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[block] Replace gPXE block-device API with an iPXE asynchronous interface
The block device interface used in gPXE predates the invention of even
the old gPXE data-transfer interface, let alone the current iPXE
generic asynchronous interface mechanism. Bring this old code up to
date, with the following benefits:
o Block device commands can be cancelled by the requestor. The INT 13
layer uses this to provide a global timeout on all INT 13 calls,
with the result that an unexpected passive failure mode (such as
an iSCSI target ACKing the request but never sending a response)
will lead to a timeout that gets reported back to the INT 13 user,
rather than simply freezing the system.
o INT 13,00 (reset drive) is now able to reset the underlying block
device. INT 13 users, such as DOS, that use INT 13,00 as a method
for error recovery now have a chance of recovering.
o All block device commands are tagged, with a numerical tag that
will show up in debugging output and in packet captures; this will
allow easier interpretation of bug reports that include both
sources of information.
o The extremely ugly hacks used to generate the boot firmware tables
have been eradicated and replaced with a generic acpi_describe()
method (exploiting the ability of iPXE interfaces to pass through
methods to an underlying interface). The ACPI tables are now
built in a shared data block within .bss16, rather than each
requiring dedicated space in .data16.
o The architecture-independent concept of a SAN device has been
exposed to the iPXE core through the sanboot API, which provides
calls to hook, unhook, boot, and describe SAN devices. This
allows for much more flexible usage patterns (such as hooking an
empty SAN device and then running an OS installer via TFTP).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Remove unnecessary constraint on DBG_ENABLE()/DBG_DISABLE()
DBG_ENABLE() and DBG_DISABLE() are currently constrained to enabling
and disabling only debug levels that are compiled in for the current
object. For example, a DBG_ENABLE(DBGLVL_EXTRA) in foo.c will not be
able to affect output from other objects at DBGLVL_EXTRA unless foo.c
is itself compiled with DBGLVL_EXTRA enabled.
Partially fix by removing this unnecessary constraint. (Note that it
is still necessary for at least one debug level to be compiled in for
the object invoking DBG_ENABLE()/DBG_DISABLE().)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xfer_window_changed() can be used to notify peers that an interface is
now ready to accept data. This can potentially be used to eliminate
the need for wasteful processes that simply poll xfer_window() until
the window becomes non-zero.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[infiniband] Add the concept of an Infiniband upper-layer driver
Replace the explicit calls from the Infiniband core to the IPoIB layer
with the general concept of an Infiniband upper-layer driver
(analogous to a PCI driver) which can create arbitrary devices on top
of Infiniband devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Add the concept of a network upper-layer driver
Add the concept of a network upper-layer driver, which can create
arbitrary devices on top of network devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[retry] Hold reference while timer is running and during expiry callback
Guarantee that a retry timer cannot go out of scope while the timer is
running, and provide a guarantee to the expiry callback that the timer
will remain in scope during the entire callback (similar to the
guarantee provided to interface methods).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[xfer] Generalise metadata "whence" field to "flags" field
iPXE has never supported SEEK_END; the usage of "whence" offers only
the options of SEEK_SET and SEEK_CUR and so is effectively a boolean
flag. Further flags will be required to support additional metadata
required by the Fibre Channel network model, so repurpose the "whence"
field as a generic "flags" field.
xfer_seek() has always been used with SEEK_SET, so remove the "whence"
field altogether from its argument list.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Fix misaligned table entries when using gcc 4.5
Declarations without the accompanying __table_entry cause misalignment
of the table entries when using gcc 4.5. Fix by adding the
appropriate __table_entry macro or (where possible) by removing
unnecessary forward declarations.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[compiler] Prevent empty weak function stubs from being removed
Even with the noinline specifier added by commit 1a260f8, gcc may skip
calls to non-inlinable functions that it knows have no side
effects. This caused the get_cached_dhcpack() call in start_dhcp(),
the weak stub of which has no code in its body, to be removed,
preventing cached DHCP from working.
Fix by adding a __keepme macro to compiler.h expanding to asm(""), as
recommended by gcc's info page, and using it in the weak stub for
get_cached_dhcpack().
Reported-by: Aaron Brooks <aaron@brooks1.net>
Tested-by: Aaron Brooks <aaron@brooks1.net>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the tap driver that can be used like:
$ ./ipxe.linux --net tap,if=tap0,mac=00:0c:29:c5:39:a1
The if setting is mandatory.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support qemu-like arguments for network setup:
--net driver_name[,setting=value]*
and global settings:
--settings setting=value[,setting=value]*
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the base to build linux drivers and the linux UI code on. UI
fills device requests, which are later walked over by the linux
root_driver and delegated to specific linux drivers.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There exists an smbios userspace library so implementing this is
probably possible, but doesn't seem really important to have in
userspace. Hence provide a dummy implementation returning an error.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add user access API for linux.
On linux userspace virtual == user == phys addresses. Physical
addresses also being the same is wrong, but there is no general way of
converting userspace addresses to physical as what appears to be
contiguous in userspace is physically fragmented. Currently only the
DMA memory is special-cased, but its conversion to bus addresses is
done in phys_to_bus. This is known to break virtio as it is passing
phys addresses to the virtual device.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown