[efi] Provide Map_Mem() and associated UNDI callbacks
Some drivers are known to call the optional Map_Mem() callback without
first checking that the callback exists. Provide a usable basic
implementation of Map_Mem() along with the other callbacks that become
mandatory if Map_Mem() is provided.
Note that in theory the PCI I/O protocol is allowed to require
multiple calls to Map(), with each call handling only a subset of the
overall mapped range. However, the reference implementation in EDK2
assumes that a single Map() will always suffice, so we can probably
make the same simplifying assumption here.
Tested with the Intel E3522X2.EFI driver (which, incidentally, fails
to cleanly remove one of its mappings).
Originally-implemented-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Work around broken reset mechanism in i219 devices
The i219 appears to have a seriously broken reset mechanism. After
any transmit or receive activity, resetting the card will break both
the transmit and receive datapaths until the next PCI bus reset.
The Linux and BSD drivers include a convoluted workaround authored by
Intel which involves setting a bit in the undocumented FEXTNVM11
register, then transmitting a dummy 512-byte packet containing garbage
data, then reconfiguring the receive descriptor prefetch thresholds
and temporarily reenabling the receive datapath. The comments in the
Intel fix do not even remotely match what the code actually does, and
the code accidentally leaves the transmitter enabled after use.
Experimentation suggests that an equivalent fix is to simply set the
undocumented bit in FEXTNVM11 before enabling the transmit or receive
descriptor rings.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ena] Fix spurious uninitialised variable warning on older versions of gcc
Some older versions of gcc (observed with gcc 4.7.2) report a spurious
uninitialised variable warning in ena_get_device_attributes(). Work
around this warning by manually inlining the relevant code (which has
only a single call site).
Reported-by: xbgmsharp <xbgmsharp@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most drivers do not utilise an MII interface, since the link state is
typically available directly from a memory-mapped register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The SnpDxe driver raises the task priority level to TPL_CALLBACK when
calling the UNDI entry point. This does not appear to be a documented
requirement, but we should probably match the behaviour of SnpDxe to
minimise surprises to third party code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification has an implicit and demonstrably incorrect
requirement (in the Mem_IO() calling convention) that any UNDI network
device has at most one memory BAR and one I/O BAR.
Some UEFI platforms have been observed to report the existence of
non-existent additional I/O BARs, causing iPXE to select the wrong
BAR. This problem does not affect the SnpDxe driver, since that
driver will always choose the lowest numbered existent BAR of each
type.
Adjust iPXE's behaviour to match that of SnpDxe, i.e. to always select
the lowest numbered BAR(s).
Debugged-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Debugged-by: Adklei <adklei@realtek.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smsc75xx] Expose functionality shared with LAN78xx devices
The LAN78xx datapath is essentially identical to that of the SMSC75xx.
Expose the transmit, poll, and bulk IN endpoint operations to allow
for reuse by the LAN78xx driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smscusb] Allow for alternative PHY register layouts
The LAN78xx PHY interrupt source and mask registers do not match those
used by the SMSC75xx and SMSC95xx.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since we don't enable IOMMU at all, we can then simply enable the
IOMMU support by claiming the support of VIRITO_F_IOMMU_PLATFORM.
This fixes booting failure when iommu_platform is set from qemu cli.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[smscusb] Abstract out common SMSC USB device functionality
The smsc75xx and smsc95xx drivers include a substantial amount of
identical functionality, varying only in the base address of register
sets. Abstract out this common functionality to allow code to be
shared between the drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[xen] Provide 18 4kB receive buffers to work around xen-netback bug
The Xen network backend (xen-netback) suffered from a regression
between upstream Linux kernels 3.18 and 4.2 inclusive, which would
cause packet reception to fail unless at least 18 receive buffers were
available. This bug was fixed in kernel commit 1d5d485 ("xen-netback:
require fewer guest Rx slots when not using GSO").
Work around this bug in affected versions of xen-netback by providing
the requisite 18 receive buffers.
Reported-by: Taylor Schneider <tschneider@live.com>
Tested-by: Taylor Schneider <tschneider@live.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[hyperv] Cope with Windows Server 2016 enlightenments
An "enlightened" external bootloader (such as Windows Server 2016's
winload.exe) may take ownership of the Hyper-V connection before all
INT 13 operations have been completed. When this happens, all VMBus
devices are implicitly closed and we are left with a non-functional
network connection.
Detect when our Hyper-V connection has been lost (by checking the
SynIC message page MSR). Reclaim ownership of the Hyper-V connection
and reestablish any VMBus devices, without disrupting any existing
iPXE state (such as IPv4 settings attached to the network device).
Windows Server 2016 will not cleanly take ownership of an active
Hyper-V connection. Experimentation shows that we can quiesce by
resetting only the SynIC message page MSR; this results in a
successful SAN boot (on a Windows 2012 R2 physical host). Choose to
quiesce by resetting (almost) all MSRs, in the hope that this will be
more robust against corner cases such as a stray synthetic interrupt
occurring during the handover.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On most Intel NICs, Auto-Speed Detection Enable (ASDE) can be used to
automatically detect the correct link speed by sampling the link using
the internal PHY. This feature is automatically inhibited when not
appropriate for the physical link (e.g. when using internal SerDes
mode on the 8254x).
On the i350 datasheet ASDE is a reserved bit, but the relevant
auto-speed detection hardware appears still to be present. However,
enabling ASDE on the i350 1000BASE-KX backplane NIC seems to cause an
immediate link failure. It is possible that the auto-speed detection
hardware is still present, is not connected to a physical link, and is
not inhibited from being applied in this mode.
Work around this problem by adding an INTEL_NO_ASDE flag bit
(analogous to INTEL_NO_PHY_RST), and applying this for the i350
backplane NIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[intel] Show original CTRL and STATUS values in debugging output
In situations where iPXE fails to reach link-up as expected, it is
useful to know the original values of the CTRL and STATUS registers
prior to our reset attempt.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[thunderx] Use ThunderxConfigProtocol to obtain board configuration
Following changes were introduced:
- added GetBgxProp and GetLmacProp methods to ThunderxConfigProtocol
- replaced direct BOARD_CFG access with usage of introduced methods
- removed redundant BOARD_CFG
- changed GUID of ThunderxConfigProtocol, as this is not compatible
with previous version
- changed UINTN* to UINT64* buffer type to fix issue on 32-bit
platforms with MAC address
This change allows us to avoid alignment of BOARD_CFG definitions
every time it changes in UEFI.
Signed-off-by: Konrad Adamczyk <konrad.adamczyk@cavium.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
B0_CTST is a 24bit register according to the vendor driver (sk98lin).
A 16bit read on B0_CTST will always return 0 for Y2_VAUX_AVAIL
(1<<16), so use a 32bit read when testing Y2_VAUX_AVAIL.
[This patch is copied directly from the Linux kernel tree.]
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The value of ( ( x & 0x0c00 ) | 0x0c00 ) is always 0x0c00 regardless
of the value of x, and so the read_csr() is redundant. (There are no
read side effects for this register, according to the datasheet.)
This line of code originated in Linux kernel 2.3.19pre1 as
a->write_csr(ioaddr, 80, a->read_csr(ioaddr, 80) | 0x0c00);
and was modified in kernel 2.3.41pre4 to read
a->write_csr(ioaddr, 80, (a->read_csr(ioaddr, 80) & 0x0C00) | 0x0c00);
In the absence of commit messages, the intention of the code is
unclear. However, the logic resulting in a fixed value of 0x0c00 has
remained unaltered for over 17 years, and can probably be assumed to
have the correct overall result.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[infiniband] Return status code from ib_create_cq() and ib_create_qp()
Any underlying errors arising during ib_create_cq() or ib_create_qp()
are lost since the functions simply return NULL on error. This makes
debugging harder, since a debug-enabled build is required to discover
the root cause of the error.
Fix by returning a status code from these functions, thereby allowing
any underlying errors to be propagated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[eoib] Avoid passing a NULL I/O buffer to netdev_tx_complete_err()
Report errors in eoib_duplicate() via netdev_tx_err() rather than
netdev_tx_complete_err(), since netdev_tx_complete_err() accepts only
valid I/O buffers that are currently in the network device's transmit
queue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Skip cable detection at initialisation where possible
We currently request cable detection in PXE_OPCODE_INITIALIZE to work
around buggy Emulex drivers (see commit c0b61ba ("[efi] Work around
bugs in Emulex NII driver")).
This causes problems with some other NII drivers (e.g. Mellanox),
which may time out if the underlying link is intrinsically slow to
come up.
Attempt to work around both problems simultaneously by requesting
cable detection only if the underlying NII driver does not support
link status reporting via PXE_OPCODE_GET_STATUS. (This is based on a
potentially incorrect assumption that the buggy Emulex drivers do not
claim to report link status via PXE_OPCODE_GET_STATUS.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several files define the ARRAY_SIZE() macro as used in Linux. Provide
a common definition for this in include/compiler.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some VF data is not cleared with reset, so make sure to return all the
settings to default before configuring the VF.
This fixes an issue where network packets would fail to be received if
the VF was previously used by the linux ixgbevf driver.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[thunderx] Don't disable NIC when exiting from iPXE
According to ThunderX Errata G-17560, NIC_PF_CFG[ENA] bit should not
be cleared at exit. This allows other drivers to access the NIC regs
correctly.
Signed-off-by: Konrad Adamczyk <konrad.adamczyk@cavium.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
It is required to reset BGX context state for the LMAC using
BGX_CMR_CONFIG register.
This solves problem with network connectivity in Linux booted from
iPXE.
Signed-off-by: Bartosz Szczepanek <bartosz.szczepanek@cavium.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown