[librm] Allow for the PIC interrupt vector offset to be changed
Some external code (observed with FreeBSD's bootloader) will continue
to make INT 13 calls after reconfiguring the 8259 PIC to change the
vector offsets for IRQs. If an IRQ (e.g. the timer IRQ) subsequently
occurs while iPXE is in protected mode, this will cause a general
protection fault since the corresponding IDT entry is empty.
A general protection fault is INT 0x0d, which happens to overlap with
the original IRQ5. We therefore do have an ISR set up to handle a
general protection fault, but this ISR simply reflects the interrupt
down to the real-mode INT 0x0d and then attempts to return. Since our
ISR is expecting a hardware interrupt rather than a general protection
fault, it doesn't remove the error code from the stack before issuing
the iret instruction; it therefore attempts to return to a garbage
address. Since the segment part of this address is likely to be
invalid, a second general protection fault occurs. This cycle
continues until we run out of stack space and triple fault.
Fix by reflecting all INTs down to real mode. This actually reduces
the code size by four bytes (but increases the bss size by almost
2kB).
Reported-by: Brian Rak <dn@devicenull.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[lkrnprefix] Make real-mode setup code relocatable
The bzImage boot protocol allows the real-mode code to be loaded at
any segment within base memory. (The fact that both iPXE and recent
versions of Syslinux will load the real-mode code at 1000:0000 is a
coincidence; it is not guaranteed by the specification.)
Fix by making the code relocatable.
Reported-by: Andrew Stuart <andrew@shopcusa.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Rework geniso and genliso to provide a single merged utility for
generating ISO images.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The .lkrn prefix currently provides a zImage kernel with unused setup
sectors and the whole iPXE binary placed within the "protected mode
kernel" portion of the zImage.
The work carried out years ago to create the .mrom format provides a
mechanism allowing the iPXE binary to be split into a small real-mode
header and a larger payload. This neatly matches the way that a
bzImage is loaded: the "setup sectors" can contain the header and the
"protected mode kernel" can contain the payload.
This removes the size restrictions on an iPXE .lkrn image (and hence
on derived image formats such as .iso).
Also remove obsolete copyright information, since none of the original
code or functionality now remains.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[profile] Allow interrupts to be excluded from profiling results
Interrupt processing adds noise to profiling results. Allow
interrupts (from within protected mode) to be profiled separately,
with time spent within the interrupt handler being excluded from any
other profiling currently in progress.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[undi] Place an upper limit on the number of PXENV_UNDI_ISR calls per poll
PXENV_UNDI_ISR calls may implicitly refill the underlying receive
ring, and so could continue to retrieve packets indefinitely. Place
an upper limit on the number of calls to PXENV_UNDI_ISR per call to
undinet_poll().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When making a call from real mode to protected mode, we save and
restore the global and interrupt descriptor table registers. The
restore currently takes place after returning to real mode, which
generates two EXCEPTION_NMIs and corresponding VM exits when running
under KVM on an Intel CPU.
Avoid the VM exits by restoring the descriptor table registers inside
prot_to_real, while still running in protected mode.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Speed up real-to-protected mode transition under KVM
Ensure that all segment registers have zero in the low two bits before
transitioning to protected mode. This allows the CPU state to
immediately be deemed to be "valid", and eliminates the need for any
further emulated instructions.
Load the protected-mode interrupt descriptor table after switching to
protected mode, since this avoids triggering an EXCEPTION_NMI and
corresponding VM exit.
This reduces the time taken by real_to_prot under KVM by around 50%.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Speed up protected-to-real mode transition under KVM
On an Intel CPU supporting VMX, KVM will emulate instructions while
the CPU state remains "invalid". In real mode, the CPU state is
defined to be "invalid" if any segment register has a base which is
not equal to (sreg<<4) or a limit which is not equal to 64kB.
We don't actually use the base stored in the REAL_DS descriptor for
any significant purpose. Change the base stored in this descriptor to
be equal to (REAL_DS<<4). A segment register loaded with REAL_DS is
then automatically valid in both real and protected modes. This
allows KVM to stop emulating instructions much sooner.
The only use of REAL_DS for memory accesses currently occurs in the
indirect ljmp within prot_to_real. Change this to a direct ljmp,
storing rm_cs in .text16 as part of the ljmp instruction. This
removes the only memory access via REAL_DS (thereby allowing for the
above descriptor base address hack), and also simplifies the ljmp
instruction (which will still have to be emulated).
Load the real-mode interrupt descriptor table register before
switching to real mode, since this avoids triggering an EXCEPTION_NMI
and corresponding VM exit.
This reduces the time taken by prot_to_real under KVM by around 65%.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The mode-transition code involves paths which switch back and forth
between the .text and .text16 sections. At present, only the start of
each function is labelled, which makes it difficult to decode
addresses within the parts of the function existing in a different
section.
Add explicit labels at the start of each section change, so that
addresses can be meaningfully decoded to the nearest label.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pcbios] Do not switch to real mode to sleep the CPU
Now that we can handle interrupts while in protected mode, there is no
need to switch to real mode just to halt the CPU.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pcbios] Do not switch to real mode to check for timer interrupt
The currticks() function is called at least once per TCP packet, and
so is performance-critical. Switching to real mode just to allow the
timer interrupt to fire is expensive when running inside a virtual
machine, and imposes a significant performance cost.
Fix by enabling interrupts without switching to real mode. This
results in an approximately 100% increase in download speed when
running under KVM.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We now have the ability to handle interrupts while in protected mode,
and so no longer need to set up a dedicated interrupt descriptor table
while running COM32 executables.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When running in a virtual machine, switching to real mode may be
expensive. Allow interrupts to be enabled while in protected mode and
reflected down to the real-mode interrupt handlers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Use genuine real mode to accelerate operation in virtual machines
We currently use flat real mode wherever real mode is required. This
guarantees that we will not surprise some unsuspecting external caller
which has carefully set up flat real mode by suddenly reducing the
segment limits to 64kB.
However, operating in flat real mode imposes a severe performance
penalty in some virtualisation environments, since some CPUs cannot
fully virtualise flat real mode and so the hypervisor must fall back
to emulation. In particular, operating under KVM on a pre-Westmere
Intel CPU will be at least an order of magnitude slower, to the point
that there is a visible teletype effect when printing anything to the
BIOS console. (Older versions of KVM used to cheat and ignore the
"flat" part of flat real mode, which masked the problem.)
Switch (back) to using genuine real mode with 64kB segment limits
instead of flat real mode. Hopefully this won't break anything.
Add an explicit switch to flat real mode before returning to the BIOS
from the ROM prefix, since we know that a PMM BIOS will call the ROM
initialisation point (and potentially the BEV) in flat real mode.
As noted in previous commit messages, it is not possible to restore
the real-mode segment limits after a transition to protected mode,
since there is no way to know which protected-mode segment descriptor
was originally used to initialise the limit portion of the segment
register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Fix __libgcc attribute for recent gcc versions
We observed some time ago (in commit 4ce8d61 "Import various libgcc
functions from syslinux") that gcc seems to treat calls to the
implicit arithmetic functions (e.g. __udivdi3()) as being affected by
-mregparm but unaffected by -mrtd.
This seems to be no longer the case with current gcc versions, which
treat calls to these functions as being affected by both -mregparm and
-mrtd, as expected.
There is nothing obvious in the gcc changelogs to indicate precisely
when this happened. From experimentation with available gcc versions,
the change occurred sometime between v4.6.3 and v4.7.2. We assume
that only versions up to v4.6.x require the special treatment.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[bios] Fix screen clearing on even more buggy BIOSes
Some BIOSes (observed with a ProLiant DL360p Gen8 SE) perform no range
checking whatsoever on the parameters passed to INT10,06 and will
therefore happily write to an area beyond the end of video RAM. The
area immediately following the video RAM tends to be the VGA BIOS ROM
image. Overwriting the VGA BIOS leads to an interesting variety of
crashes and reboots.
Fix by specifying an exact width and height to be cleared, rather than
passing in large values and relying upon the BIOS to truncate them to
the appropriate range.
Reported-by: Alex Davies <adavies@jumptrading.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Disable SNP devices when running iPXE as the application
Some UEFI builds will set up a timer to continuously poll any SNP
devices. This can drain packets from the network device's receive
queue before iPXE gets a chance to process them.
Use netdev_rx_[un]freeze() to explicitly indicate when we expect our
network devices to be driven via the external SNP API (as we do with
the UNDI API on the standard BIOS build), and disable the SNP API
except when receive queue processing is frozen.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFIRC() uses PLATFORM_TO_ERRNO(), which evaluates its argument twice
(and can't trivially use a braced-group expression or an inline
function to avoid this, since it gets used outside of function
context).
The expression "EFIRC(main())" will therefore end up calling main()
twice, which is not the intended behaviour. Every other instance of
EFIRC() is of the simple form "EFIRC(rc)", so fix by converting this
instance to match.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[image] Add "--timeout" parameter to image downloading commands
iPXE will detect timeout failures in several situations: network
link-up, DHCP, TCP connection attempts, unacknowledged TCP data, etc.
This does not cover all possible circumstances. For example, if a
connection to a web server is successfully established and the web
server acknowledges the HTTP request but never sends any data in
response, then no timeout will be triggered. There is no timeout
defined within the HTTP specifications, and the underlying TCP
connection will not generate a timeout since it has no way to know
that the HTTP layer is expecting to receive data from the server.
Add a "--timeout" parameter to "imgfetch", "chain", etc. If no
progress is made (i.e. no data is downloaded) within the timeout
period, then the download will be aborted.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Do not clobber stack segment when returning to BIOS
Commit c429bf0 ("[romprefix] Store boot bus:dev.fn address as autoboot
device location") introduced a regression by using register %cx to
temporarily hold the PCI bus:dev.fn address, despite the fact that %cx
was already being used to hold the stored BIOS stack segment.
Consequently, when returning to the BIOS after a failed or cancelled
boot attempt, iPXE would end up calling INT 18 with the stack segment
set equal to the PCI bus:dev.fn address. Writing to essentially
random areas of memory tends to upset even the more robust BIOSes.
Fix by using register %ax to temporarily hold the PCI bus:dev.fn
address.
Reported-by: Anton D. Kachalov <mouse@yandex-team.ru>
Tested-by: Anton D. Kachalov <mouse@yandex-team.ru>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[bzimage] Report exact initrd length via bzImage header
iPXE currently pads initrd images to a multiple of 4kB and inserts
zero padding between images, as required by some versions of the Linux
kernel. The overall length reported via the ramdisk_size field in the
bzImage header includes this zero padding.
This causes problems when using memdisk to load a gzip-compressed disk
image. memdisk treats the ramdisk_size field as containing the exact
length of the initrd image, and uses this length to locate the 8-byte
gzip footer. This will generally cause memdisk to fail to decompress
the disk image.
Fix by reporting the exact length of the initrd image set, including
any padding inserted between images but excluding any padding added at
the end of the final image.
Reported-by: Levente LEVAI <levail@aviatronic.hu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[prefix] Ignore PCI autoboot device location if set to 00:00.0
qemu can load an option ROM which is not associated with a particular
PCI device using the "-option-rom" syntax. Under these circumstances,
we should ignore the PCI bus:dev.fn address that we expect to find in
%ax on entry to the initialisation vector.
Fix by using the PCI bus:dev.fn address only if it is non-zero. Since
00:00.0 will always be the host bridge, it can never be the address of
a network card.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Store boot bus:dev.fn address as autoboot device location
Per the BIOS Boot Specification, the initialization phase of the ROM
is called with the PFA (PCI Function Address) in the %ax register.
The intention is that the ROM code will store that device address
somewhere and use it for booting from that device when the Boot Entry
Vector (BEV) is called. iPXE does store the PFA, but doesn't use it
to select the boot network device. This renders BIOS IPL lists fairly
ineffective.
Fix by using the BBS-specified bus:dev.fn address as the autoboot
device location.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[romprefix] Allow ROM banner timeout to be configured independently
iPXE currently prints a "Press Ctrl-B" banner twice: once when the ROM
is first called for initialisation and again if we attempt to boot
from the ROM. This slows boot, especially when the NIC is not the
primary boot device. Tools such as libguestfs make use of QEMU VMs
for performing maintenance on disk images and may make use of NICs in
the VM for network support. If iPXE introduces a static init-time
delay, that directly translates to increased runtime for the tools.
Fix by allowing the ROM banner timeout to be configured independently
of the main banner timeout.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for parsing of URIs containing literal IPv6 addresses
(e.g. "http://[fe80::69ff:fe50:5845%25net0]/boot.ipxe").
Duplicate URIs by directly copying the relevant fields, rather than by
formatting and reparsing a URI string. This relaxes the requirements
on the URI formatting code and allows it to focus on generating
human-readable URIs (e.g. by not escaping ':' characters within
literal IPv6 addresses). As a side-effect, this allows relative URIs
containing parameter lists (e.g. "../boot.php##params") to function
as expected.
Add validity check for FTP paths to ensure that only printable
characters are accepted (since FTP is a human-readable line-based
protocol with no support for character escaping).
Construct TFTP next-server+filename URIs directly, rather than parsing
a constructed "tftp://..." string,
Add self-tests for URI functions.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[cmdline] Rename "console" command's --bpp option to --depth
Rename the "--bpp" option to "--depth", to free up the single-letter
option "-b" for "--bottom" in preparation for adding margin support.
This does not break backwards compatibility with documented features,
since the "console" command has not yet been documented.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[vesafb] Allow for an arbitrary margin around the text area
Allow for an arbitrary margin to be specified in the console
configuration. If the actual screen size does not match the requested
screen size, then update any margins specified so that they remain in
the same place relative to the requested screen size. If margins are
unspecified (i.e. zero), then leave them as zero.
The underlying assumption here is that any specified margins are
likely to describe an area within a background picture, and so should
remain in the same place relative to that background picture.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[vesafb] Set "magic" colour to transparent when a background picture is used
Use the magic colour facility to cause the user interface background
to become transparent when we have a background picture.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown