[build] Allow assembler section type character to vary by architecture
On some architectures (such as ARM) the "@" character is used as a
comment delimiter. A section type argument such as "@progbits"
therefore becomes "%progbits".
This is further complicated by the fact that the "%" character has
special meaning for inline assembly when input or output operands are
used, in which cases "@progbits" becomes "%%progbits".
Allow the section type character(s) to be defined via Makefile
variables.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[linda] Use standard readq() and writeq() implementations
This driver is the original source of the current readq() and writeq()
implementations for 32-bit iPXE. Switch to using the now-centralised
definitions, to avoid including architecture-specific code in an
otherwise architecture-independent driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Do not unconditionally preserve flags across virt_call()
Commit 196f0f2 ("[librm] Convert prot_call() to a real-mode near
call") introduced a regression in which any deliberate modification to
the low 16 bits of the CPU flags (in struct i386_all_regs) would be
overwritten with the original flags value at the time of entry to
prot_call().
The regression arose because the alignment requirements of the
protected-mode stack necessitated the insertion of two bytes of
padding immediately below the prot_call() return address. The
solution chosen was to extend the existing "pushfl / popfl" pair to
"pushfw;pushfl / popfl;popfw". The extra "pushfw / popfw" appears at
first glance to be a no-op, but fails to take into account the fact
that the flags restored by popfl may have been deliberately modified
by the protected-mode function.
Fix by replacing "pushfw / popfw" with "pushw %ss / popw %ss". While
%ss does appear within struct i386_all_regs, any modification to the
stored value has always been ignored by prot_call() anyway.
The most visible symptom of this regression was that SAN booting would
fail since every INT 13 call would be chained to the original INT 13
vector.
Reported-by: Vishvananda Ishaya <vishvananda@gmail.com>
Reported-by: Jamie Thompson <forum.ipxe@jamie-thompson.co.uk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is no practical way to generate an underlength ARP packet since
an ARP packet is always padded up to the minimum Ethernet frame length
(or dropped by the receiving Ethernet hardware if incorrectly padded),
but the absence of an explicit check causes warnings from some
analysis tools.
Fix by adding an explicit check on the I/O buffer length.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The assumption in asn1_type() that an ASN.1 cursor will always contain
a type byte is incorrect. A cursor that has been cleanly invalidated
via asn1_invalidate_cursor() will contain a type byte, but there are
other ways in which to arrive at a zero-length cursor.
Fix by explicitly checking the cursor length in asn1_type(). This
allows asn1_invalidate_cursor() to be reduced to simply zeroing the
length field.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tls] Avoid potential out-of-bound reads in length fields
Many TLS records contain variable-length fields. We currently
validate the overall record length, but do so only after reading the
length of the variable-length field. If the record is too short to
even contain the length field, then we may read uninitialised data
from beyond the end of the record.
This is harmless in practice (since the subsequent overall record
length check would fail regardless of the value read from the
uninitialised length field), but causes warnings from some analysis
tools.
Fix by validating that the overall record length is sufficient to
contain the length field before reading from the length field.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Work around broken GetFontInfo() implementations
Several UEFI platforms are known to return EFI_NOT_FOUND when asked to
retrieve the system default font information via GetFontInfo(). Work
around these broken platforms by iterating over the glyphs to find the
maximum height used by a printable character.
Originally-fixed-by: Jonathan Dieter <jdieter@lesbg.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some EoIB implementations utilise an EoIB-to-Ethernet gateway device
that does not perform a FullMember join to the multicast group for the
EoIB broadcast domain. This has various exciting side-effects, such
as requiring every EoIB node to send every broadcast packet twice.
As an added bonus, the gateway may also break the EoIB MAC address to
GID mapping protocol by sending Ethernet-sourced packets from the
wrong QPN.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[eoib] Allow the multicast group to be forcefully created
Some EoIB implementations require each individual EoIB node to create
the multicast group for the EoIB broadcast domain.
It is left as an exercise for the interested reader to determine how
such an implementation might ever allow the parameters of such a
multicast group to be changed without requiring a simultaneous upgrade
of every driver on every operating system on every machine currently
attached to the fabric.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some EoIB implementations transmit a vendor-proprietary heartbeat
packet on the same multicast group used to provide the EoIB broadcast
domain.
Silently ignore these heartbeat packets, to avoid cluttering up the
network interface error statistics.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EoIB is a fairly simple protocol in which raw Ethernet frames
(excluding the CRC) are encapsulated within Infiniband Unreliable
Datagrams, with a four-byte fixed EoIB header (which conveys no actual
information). The Ethernet broadcast domain is provided by a
multicast group, similar to the IPoIB IPv4 multicast group.
The mapping from Ethernet MAC addresses to Infiniband address vectors
is achieved by snooping incoming traffic and building a peer cache
which can then be used to map a MAC address into a port GID. The
address vector is completed using a path record lookup, as for IPoIB.
Note that this requires every packet to include a GRH.
Add basic support for EoIB devices. This driver is substantially
derived from the IPoIB driver. There is currently no mechanism for
automatically creating EoIB devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[infiniband] Make IPoIB support configurable at build time
Add a build configuration option VNIC_IPOIB to control whether or not
IPoIB support is included for Infiniband devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipoib] Resimplify test for received broadcast packets
Commit e62e52b ("[ipoib] Simplify test for received broadcast
packets") relies upon the multicast LID being present in the
destination address vector as passed to ipoib_complete_recv().
Unfortunately, this information is not present in many Infiniband
devices' completion queue entries.
Fix by testing instead for the presence of a multicast GID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[pcbios] Restrict external memory allocations to the low 4GB
When running the 64-bit BIOS version of iPXE, restrict external memory
allocations to the low 4GB to ensure that allocations (such as for
initrds) fall within our identity-mapped memory region, and will be
accessible to the potentially 32-bit operating system.
Move largest_memblock() back to memtop_umalloc.c, since this change
imposes a restriction that applies only to BIOS builds.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[infiniband] Avoid multiple calls to ib_cmrc_shutdown()
When a CMRC connection is closed, the deferred shutdown process calls
ib_destroy_qp(). This will cause the receive work queue entries to
complete in error (since they are being cancelled), which will in turn
reschedule the deferred shutdown process. This eventually leads to
ib_destroy_conn() being called on a connection that has already been
freed.
Fix by explicitly cancelling any pending shutdown process after the
shutdown process has completed.
Ironically, this almost exactly reverts commit 019d4c1 ("[infiniband]
Use a one-shot process for CMRC shutdown"); prior to the introduction
of one-shot processes the only way to achieve a one-shot process was
for the process to cancel itself.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Add support for running in 64-bit long mode
Add support for running the BIOS version of iPXE in 64-bit long mode.
A 64-bit BIOS version of iPXE can be built using e.g.
make bin-x86_64-pcbios/ipxe.usb
make bin-x86_64-pcbios/8086100e.mrom
The 64-bit BIOS version should appear to function identically to the
normal 32-bit BIOS version. The physical memory layout is unaltered:
iPXE is still relocated to the top of the available 32-bit address
space. The code is linked to a virtual address of 0xffffffffeb000000
(in the negative 2GB as required by -mcmodel=kernel), with 4kB pages
created to cover the whole of .textdata. 2MB pages are created to
cover the whole of the 32-bit address space.
The 32-bit portions of the code run with VIRTUAL_CS and VIRTUAL_DS
configured such that truncating a 64-bit virtual address gives a
32-bit virtual address pointing to the same physical location.
The stack pointer remains as a physical address when running in long
mode (although the .stack section is accessible via the negative 2GB
virtual address); this is done in order to simplify the handling of
interrupts occurring while executing a portion of 32-bit code with
flat physical addressing via PHYS_CODE().
Interrupts may be enabled in either 64-bit long mode, 32-bit protected
mode with virtual addresses, 32-bit protected mode with physical
addresses, or 16-bit real mode. Interrupts occurring in any mode
other than real mode will be reflected down to real mode and handled
by whichever ISR is hooked into the BIOS interrupt vector table.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a 64-bit build, the entirety of the 32-bit address space is
identity-mapped and so any valid physical address may immediately be
used as a virtual address. Conversely, a virtual address that is
already within the 32-bit address space may immediately be used as a
physical address.
A valid virtual address that lies outside the 32-bit address space
must be an address within .textdata, and so can be converted to a
physical address by adding virt_offset.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[librm] Mark virt_offset, text16, data16, rm_cs, and rm_ds as constant
The physical locations of .textdata, .text16 and .data16 are constant
from the point of view of C code. Mark the relevant variables as
constant to allow gcc to optimise out redundant reads.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No callers of prot_to_phys, phys_to_prot, or intr_to_prot require the
flags to be preserved. Remove the unnecessary pushfl/popfl pairs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown