UEFI platforms may provide a watchdog timer, which will reboot the
machine if an operating system takes more than five minutes to load.
This can cause long-lived iPXE downloads (or interactive shell
sessions) to unexpectedly reboot.
Fix by resetting the watchdog timer every ten seconds while the iPXE
main processing loop continues to run.
Reported-by: Bradley B Williams <bradleybwilliams@swbell.net>
Reported-by: John Clark <john.r.clark.3@gmail.com>
Reported-by: wdriever@gmail.com
Reported-by: Charlie Beima <cbeima@indiana.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[crypto] Support SHA-{224,384,512} in X.509 certificates
Add support for SHA-224, SHA-384, and SHA-512 as digest algorithms in
X.509 certificates, and allow the choice of public-key, cipher, and
digest algorithms to be configured at build time via config/crypto.h.
Originally-implemented-by: Tufan Karadere <tufank@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[tls] Do not access beyond the end of a 24-bit integer
The current implementation handles big-endian 24-bit integers (which
occur in several TLS record types) by treating them as big-endian
32-bit integers which are shifted by 8 bits. This can result in
"Invalid read" errors when running under valgrind, if the 24-bit field
happens to be exactly at the end of an I/O buffer.
Fix by ensuring that we touch only the three bytes which comprise the
24-bit integer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[serial] Check for UART existence in uart_select()
Check for existence of the UART in uart_select(), not just in
uart_init(). This allows uart_select() to refuse to set a non-working
address in uart->base, which in turns means that the serial console
code will not attempt to use a non-existent UART.
Reported-by: Torgeir Wulfsberg <Torgeir.Wulfsberg@kongsberg.com>
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[comboot] Avoid dragging in serial console support unconditionally
When the ability for iPXE to handle multiple serial ports was added,
the choice was made that the singular serial port referred to by
COMBOOT calls should mean the port used for the serial console. This
unintentionally caused IMAGE_COMBOOT to also enable CONSOLE_SERIAL.
Fix by providing a weak-symbol version of the serial console which
will be used if serial console support was not explicitly enabled.
Reported-by: Torgeir Wulfsberg <Torgeir.Wulfsberg@kongsberg.com>
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We do not set up any kind of virtual addressing before invoking an
ELFBoot image. Reject if the image's program headers indicate that
virtual addresses are not equal to physical addresses.
This avoids problems when loading some RHEL5 kernels, which seem to
include ELFBoot headers using virtual addressing. With this change,
these kernels are no longer detected as ELFBoot, and so may be
(correctly) detected as bzImage instead.
Reported-by: Torgeir.Wulfsberg@kongsberg.com
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow line buffer to accumulate multiple lines, with buffered_line()
returning each freshly-completed line as it is encountered. This
allows buffered lines to be subsequently processed as a group.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Allow network devices to disclaim IRQ support at runtime
VLAN and 802.11 devices use a network device operations structure that
wraps an underlying structure. For example, the vlan_operations
structure wraps the network device operations structure of the
underlying trunk device. This can cause false positives from the
current implementation of netdev_irq_supported(), which will always
report that VLAN devices support interrupts since it has no visibility
into the support provided by the underlying trunk device.
Fix by allowing network devices to explicitly flag that interrupts are
not supported, despite the presence of an irq() method.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iscsi_tx_done() is missing "break" statements at the end of each case.
(Fortunately, this happens not to cause a bug in practice, since
iscsi_login_request_done() is effectively a no-op when completing a
data-out PDU.)
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv4] Allow IPv4 socket addresses to include a scope ID
Extend the IPv6 concept of "scope ID" (indicating the network device
index) to IPv4 socket addresses, so that IPv4 multicast transmissions
may specify the transmitting network device.
The scope ID is not (currently) exposed via the string representation
of the socket address, since IPv4 does not use the IPv6 concept of
link-local addresses (which could legitimately be specified in a URI).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv4] Redefine IP address constants to avoid unnecessary byte swapping
Redefine various IPv4 address constants and testing macros to avoid
unnecessary byte swapping at runtime, and slightly rename the macros
to prevent code from accidentally using the old definitions.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[netdevice] Avoid using zero as a network device index
Avoid using zero as a network device index, so that a zero
sin6_scope_id can be used to mean "unspecified" (rather than
unintentionally meaning "net0").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[ipv6] Treat a missing network device name as "netX"
When an IPv6 socket address string specifies a link-local or multicast
address but does not specify the requisite network device name
(e.g. "fe80::69ff:fe50:5845" rather than "fe80::69ff:fe50:5845%net0"),
assume the use of "netX".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove AXTLS headers now that no AXTLS code remains, with many thanks
to the AXTLS project for use of their cryptography code over the past
several years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the AES implementation from AXTLS with a dedicated iPXE
implementation which is slightly smaller and around 1000% faster.
This implementation has been verified using the existing self-tests
based on the NIST AES test vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generalise the existing support for performing CBC-mode block cipher
tests, and update the code to use okx() for neater reporting of test
results.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[build] Fix compiler warnings on some gcc versions
xfer_buffer() uses intf_get_dest_op() to obtain the destination
interface for xfer_deliver(), in order to check that this is the same
interface which provides xfer_buffer(). The return value from
intf_get_dest_op() (which contains the actual method implementing
xfer_deliver()) is not used.
On some gcc versions, this triggers a "value computed is not used"
warning, since the explicit type cast included within the
intf_get_dest_op() macro is treated as a "value computed".
Fix by explicitly casting the result of intf_get_dest_op() to void.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Reported-by: James A. Peltier <jpeltier@sfu.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce the cost of implementing object methods which convey no
information beyond the fact that the method has been called.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[profile] Add profile_custom() for profiling with arbitrary time units
Provide profile_custom() as a trivial wrapper around profile_update()
to allow for the use of the profiling infrastructure by code using
timers other than the default profile_timestamp() provider.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[fault] Add inject_corruption() to randomly corrupt data
Provide an inject_corruption() function that can be used to randomly
corrupt data bytes with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a generic inject_fault() function that can be used to inject
random faults with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a named configuration for qemu, based on the config.ipxe.general.h
file taken from the current qemu repository and enabling the option to
work around the missing EFI_PXE_BASE_CODE_PROTOCOL.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE does not currently provide EFI_PXE_BASE_CODE_PROTOCOL: this
causes failures when chainloading bootloaders such as shim.efi which
assume that this protocol will be present.
Provide the ability to work around these problems via the build
configuration option EFI_DOWNGRADE_UX. If this option is enabled,
then we will not install our usual EFI_LOAD_FILE_PROTOCOL
implementation, thereby allowing the platform firmware to install its
own EFI_PXE_BASE_CODE_PROTOCOL implementation on top of our
EFI_SIMPLE_NETWORK_PROTOCOL handle.
A somewhat major side-effect of this workaround is that almost all
iPXE features will be disabled.
This configuration option will be removed in future when support for
EFI_PXE_BASE_CODE_PROTOCOL is added.
Requested-by: Laszlo Ersek <lersek@redhat.com>
Requested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
[efi] Fix receive and transmit completion reporting
Fix the TxBuf value filled in by GetStatus() to report the transmit
buffer address as required by the (now clarified) specification.
Simplify "interrupt" handling in GetStatus() to report only that one
or more packets have been transmitted or received; there is no need to
report one GetStatus() "interrupt" per packet.
Simplify receive handling to dequeue received packets immediately from
the network device into an internal list (thereby avoiding the hacks
previously used to determine when to report new packet arrivals).
Originally-fixed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose the high bit of the VGA text attribute byte via the ANSI SGR
parameters 5 ("blink on") and 25 ("blink off").
Note that some video cards (and virtual machines) may display a high
intensity background colour instead of blinking text.
Signed-off-by: Christian Nilsson <nikize@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Multicast MAC addresses will never have REMAC cache entries, and the
corresponding multicast IPoIB MAC address cannot be obtained simply by
issuing an ARP request.
For the trivial volume of multicast packets that we expect to send in
any realistic scenario, the simplest solution is to send them as
broadcasts instead.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown