Warnings purge of drivers (continued)

src/drivers/net/amd8111e.c

@@ -135,7 +135,6 @@ static void amd8111e_restart(struct amd8111e_priv *lp);
 static void amd8111e_init_hw_default(struct amd8111e_priv *lp)
 {
 	unsigned int reg_val;
-	unsigned int logic_filter[2] = {0,};
 	void *mmio = lp->mmio;
 
         /* stop the chip */
@@ -198,7 +197,8 @@ static void amd8111e_init_hw_default(struct amd8111e_priv *lp)
 	writew(MIB_CLEAR, mmio + MIB_ADDR);
 
 	/* Clear LARF */
-	amd8111e_writeq(*(u64*)logic_filter, mmio + LADRF);
+	writel( 0, mmio + LADRF);
+	writel( 0, mmio + LADRF + 4);
 
 	/* SRAM_SIZE register */
 	reg_val = readl(mmio + SRAM_SIZE);
@@ -342,7 +342,7 @@ static void amd8111e_probe_ext_phy(struct amd8111e_priv *lp)
 
 	if (lp->ext_phy_id)
 		printf("Found MII PHY ID 0x%08x at address 0x%02x\n",
-			lp->ext_phy_id, lp->ext_phy_addr);
+		       (unsigned int) lp->ext_phy_id, lp->ext_phy_addr);
 	else
 		printf("Couldn't detect MII PHY, assuming address 0x01\n");
 }

src/drivers/net/bnx2.c

@@ -22,12 +22,14 @@
 #include "bnx2.h"
 #include "bnx2_fw.h"
 
+#if 0
 /* Dummy defines for error handling */
 #define EBUSY  1
 #define ENODEV 2
 #define EINVAL 3
 #define ENOMEM 4
 #define EIO    5
+#endif
 
 /* The bnx2 seems to be picky about the alignment of the receive buffers
  * and possibly the status block.
@@ -1165,7 +1167,7 @@ bnx2_fw_sync(struct bnx2 *bp, u32 msg_data, int silent)
 	/* If we timed out, inform the firmware that this is the case. */
 	if ((val & BNX2_FW_MSG_ACK) != (msg_data & BNX2_DRV_MSG_SEQ)) {
 		if (!silent)
-			printf("fw sync timeout, reset code = %x\n", msg_data);
+		  printf("fw sync timeout, reset code = %x\n", (unsigned int) msg_data);
 
 		msg_data &= ~BNX2_DRV_MSG_CODE;
 		msg_data |= BNX2_DRV_MSG_CODE_FW_TIMEOUT;
@@ -2033,7 +2035,7 @@ static void
 bnx2_init_rx_ring(struct bnx2 *bp)
 {
 	struct rx_bd *rxbd;
-	int i;
+	unsigned int i;
 	u16 prod, ring_prod;
 	u32 val;
 
@@ -2066,7 +2068,7 @@ bnx2_init_rx_ring(struct bnx2 *bp)
 	val = bp->rx_desc_mapping & 0xffffffff;
 	CTX_WR(bp, GET_CID_ADDR(RX_CID), BNX2_L2CTX_NX_BDHADDR_LO, val);
 
-	for (i = 0; i < bp->rx_ring_size; i++) {
+	for (i = 0; (int) i < bp->rx_ring_size; i++) {
 		rxbd = &bp->rx_desc_ring[RX_RING_IDX(ring_prod)];
 		rxbd->rx_bd_haddr_hi = 0;
 		rxbd->rx_bd_haddr_lo = virt_to_bus(&bnx2_bss.rx_buf[ring_prod][0]);
@@ -2635,8 +2637,8 @@ bnx2_probe(struct nic *nic, struct pci_device *pdev)
 	memcpy(nic->node_addr, bp->mac_addr, ETH_ALEN);
 	printf("Ethernet addr: %s\n", eth_ntoa( nic->node_addr ) );
 	printf("Broadcom NetXtreme II (%c%d) PCI%s %s %dMHz\n",
-		((CHIP_ID(bp) & 0xf000) >> 12) + 'A',
-		((CHIP_ID(bp) & 0x0ff0) >> 4),
+	        (int) ((CHIP_ID(bp) & 0xf000) >> 12) + 'A',
+	        (int) ((CHIP_ID(bp) & 0x0ff0) >> 4),
 		((bp->flags & PCIX_FLAG) ? "-X" : ""),
 		((bp->flags & PCI_32BIT_FLAG) ? "32-bit" : "64-bit"),
 		bp->bus_speed_mhz);

src/drivers/net/bnx2.h

@@ -4091,7 +4091,7 @@ struct flash_spec {
 	u32 page_size;
 	u32 addr_mask;
 	u32 total_size;
-	u8  *name;
+	char  *name;
 };
 
 struct bnx2 {

src/drivers/net/depca.c

@@ -1,5 +1,6 @@
-#warning "depca.c almost certainly won't work"
+#warning "depca.c almost certainly won't work."
 
+#if 0
 /* Not fixed for relocation yet. Probably won't work relocated above 16MB */
 #ifdef ALLMULTI
 #error multicast support is not yet implemented
@@ -791,3 +792,5 @@ DRIVER ( "depce", nic_driver, isa_driver, depca_driver,
 	 depca_probe, depca_disable );
 
 ISA_ROM ( "depca", "Digital DE100 and DE200" );
+
+#endif

src/drivers/net/dmfe.c

@@ -1022,7 +1022,7 @@ static u16 phy_read_1bit(unsigned long ioaddr)
 
 static void dmfe_parse_srom(struct nic *nic)
 {
-	char *srom = db->srom;
+	unsigned char *srom = db->srom;
 	int dmfe_mode, tmp_reg;
 
 	/* Init CR15 */

src/drivers/net/eepro.c

@@ -265,11 +265,12 @@ static unsigned eeprom_reg = EEPROM_REG_PRO;
 #define eepro_full_reset(ioaddr)	outb(RESET_CMD, ioaddr); udelay(255);
 
 /* do a nice reset */
-#define eepro_sel_reset(ioaddr) 	{ \
-					outb(SEL_RESET_CMD, ioaddr); \
-					SLOW_DOWN; \
-					SLOW_DOWN; \
-					}
+#define eepro_sel_reset(ioaddr) \
+  do {  \
+    outb ( SEL_RESET_CMD, ioaddr ); \
+    (void) SLOW_DOWN; \
+    (void) SLOW_DOWN; \
+  } while (0)
 
 /* clear all interrupts */
 #define	eepro_clear_int(ioaddr)	outb(ALL_MASK, ioaddr + STATUS_REG)
@@ -332,7 +333,7 @@ static void eepro_reset(struct nic *nic)
 	/* Intialise XMT */
 	outw((XMT_LOWER_LIMIT << 8), nic->ioaddr + xmt_bar);
 	eepro_sel_reset(nic->ioaddr);
-	tx_start = tx_end = (XMT_LOWER_LIMIT << 8);
+	tx_start = tx_end = (unsigned int) (XMT_LOWER_LIMIT << 8);
 	tx_last = 0;
 	eepro_en_rx(nic->ioaddr);
 }

src/drivers/net/mtd80x.c

@@ -534,7 +534,7 @@ static int mtd_poll(struct nic *nic, __unused int retrieve)
     if (rx_status & ErrorSummary)
     { /* there was a fatal error */
         printf( "%s: Receive error, Rx status %8.8x, Error(s) %s%s%s\n",
-                mtdx.nic_name, rx_status ,
+                mtdx.nic_name, (unsigned int) rx_status,
                 (rx_status & (LONG | RUNT)) ? "length_error ":"",
                 (rx_status & RXER) ? "frame_error ":"",
                 (rx_status & CRC) ? "crc_error ":"" );
@@ -550,7 +550,7 @@ static int mtd_poll(struct nic *nic, __unused int retrieve)
         short pkt_len = ((rx_status & FLNGMASK) >> FLNGShift) - 4;
 
         DBG ( " netdev_rx() normal Rx pkt length %d"
- 	      " status %x.\n", pkt_len, rx_status );
+ 	      " status %x.\n", pkt_len, (unsigned int) rx_status );
 
         nic->packetlen = pkt_len;
         memcpy(nic->packet, mtdx.cur_rx->skbuff, pkt_len);
@@ -619,7 +619,7 @@ static void mtd_transmit(
         DBG ( "TX Time Out" );
     } else if( tx_status & (CSL | LC | EC | UDF | HF)){
         printf( "Transmit error: %8.8x %s %s %s %s %s\n",
-                tx_status,
+                (unsigned int) tx_status,
                 tx_status & EC ? "abort" : "",
                 tx_status & CSL ? "carrier" : "",
                 tx_status & LC ? "late" : "",

src/drivers/net/natsemi.c

@@ -536,7 +536,8 @@ natsemi_init_rxd(struct nic *nic __unused)
         rxd[i].bufptr = virt_to_bus(&rxb[i*RX_BUF_SIZE]);
         if (natsemi_debug > 1)
             printf("natsemi_init_rxd: rxd[%d]=%p link=%X cmdsts=%X bufptr=%4.4x\n", 
-                   i, &rxd[i], rxd[i].link, rxd[i].cmdsts, rxd[i].bufptr);
+                   i, &rxd[i], (unsigned int) rxd[i].link, (unsigned int) rxd[i].cmdsts, 
+		   (unsigned int) rxd[i].bufptr);
     }
 
     /* load Receive Descriptor Register */
@@ -648,11 +649,11 @@ natsemi_transmit(struct nic  *nic,
         /* wait */ ;
 
     if (currticks() >= to) {
-        printf("natsemi_transmit: TX Timeout! Tx status %X.\n", tx_status);
+        printf("natsemi_transmit: TX Timeout! Tx status %X.\n", (unsigned int) tx_status);
     }
 
     if (!(tx_status & 0x08000000)) {
-	printf("natsemi_transmit: Transmit error, Tx status %X.\n", tx_status);
+	printf("natsemi_transmit: Transmit error, Tx status %X.\n", (unsigned int) tx_status);
     }
 }
 
@@ -677,7 +678,7 @@ natsemi_poll(struct nic *nic, int retrieve)
     int retstat = 0;
 
     if (natsemi_debug > 2)
-        printf("natsemi_poll: cur_rx:%d, status:%X\n", cur_rx, rx_status);
+        printf("natsemi_poll: cur_rx:%d, status:%X\n", cur_rx, (unsigned int) rx_status);
 
     if (!(rx_status & OWN))
         return retstat;
@@ -686,14 +687,14 @@ natsemi_poll(struct nic *nic, int retrieve)
 
     if (natsemi_debug > 1)
         printf("natsemi_poll: got a packet: cur_rx:%d, status:%X\n",
-               cur_rx, rx_status);
+               cur_rx, (unsigned int) rx_status);
 
     nic->packetlen = (rx_status & DSIZE) - CRC_SIZE;
 
     if ((rx_status & (DescMore|DescPktOK|RxTooLong)) != DescPktOK) {
         /* corrupted packet received */
         printf("natsemi_poll: Corrupted packet received, buffer status = %X\n",
-               rx_status);
+               (unsigned int) rx_status);
         retstat = 0;
     } else {
         /* give packet to higher level routine */

src/drivers/net/ns83820.c

@@ -631,9 +631,10 @@ static void ns83820_run_bist(struct nic *nic __unused, const char *name,
 	}
 
 	if (status & fail)
-		printf("%s failed! (0x%hX & 0x%hX)\n", name, status, fail);
+	  printf("%s failed! (0x%hX & 0x%hX)\n", name, (unsigned int) status, 
+		 (unsigned int) fail);
 	else if (timed_out)
-		printf("run_bist %s timed out! (%hX)\n", name, status);
+		printf("run_bist %s timed out! (%hX)\n", name, (unsigned int) status);
 	dprintf(("done %s in %d loops\n", name, loops));
 }
 

src/drivers/net/ns8390.c

@@ -449,11 +449,11 @@ static void ns8390_transmit(
 		/* Programmed I/O */
 		unsigned short type;
 		type = (t >> 8) | (t << 8);
-		eth_pio_write(d, eth_tx_start<<8, ETH_ALEN);
+		eth_pio_write( (unsigned char *) d, eth_tx_start<<8, ETH_ALEN);
 		eth_pio_write(nic->node_addr, (eth_tx_start<<8)+ETH_ALEN, ETH_ALEN);
 		/* bcc generates worse code without (const+const) below */
 		eth_pio_write((unsigned char *)&type, (eth_tx_start<<8)+(ETH_ALEN+ETH_ALEN), 2);
-		eth_pio_write(p, (eth_tx_start<<8)+ETH_HLEN, s);
+		eth_pio_write( (unsigned char *) p, (eth_tx_start<<8)+ETH_HLEN, s);
 		s += ETH_HLEN;
 		if (s < ETH_ZLEN) s = ETH_ZLEN;
 	}
@@ -533,7 +533,7 @@ static int ns8390_poll(struct nic *nic, int retrieve)
 #endif
 	pktoff = next << 8;
 	if (eth_flags & FLAG_PIO)
-		eth_pio_read(pktoff, (char *)&pkthdr, 4);
+		eth_pio_read(pktoff, (unsigned char *)&pkthdr, 4);
 	else
 		memcpy(&pkthdr, bus_to_virt(eth_rmem + pktoff), 4);
 	pktoff += sizeof(pkthdr);
@@ -876,9 +876,10 @@ static int eth_probe (struct dev *dev, unsigned short *probe_addrs __unused)
 	******************************************************************/
 	unsigned char c;
 	if (eth_vendor == VENDOR_NONE) {
-		char romdata[16], testbuf[32];
+		unsigned char romdata[16];
+		unsigned char testbuf[32];
 		int idx;
-		static char test[] = "NE*000 memory";
+		static unsigned char test[] = "NE*000 memory";
 		static unsigned short base[] = {
 #ifdef	NE_SCAN
 			NE_SCAN,
@@ -896,7 +897,7 @@ static int eth_probe (struct dev *dev, unsigned short *probe_addrs __unused)
 			eth_rx_start = 32 + D8390_TXBUF_SIZE;
 			c = inb(eth_asic_base + NE_RESET);
 			outb(c, eth_asic_base + NE_RESET);
-			inb(0x84);
+			(void) inb(0x84);
 			outb(D8390_COMMAND_STP |
 				D8390_COMMAND_RD2, eth_nic_base + D8390_P0_COMMAND);
 			outb(D8390_RCR_MON, eth_nic_base + D8390_P0_RCR);
@@ -907,7 +908,7 @@ static int eth_probe (struct dev *dev, unsigned short *probe_addrs __unused)
 			eth_flags |= FLAG_16BIT;	/* force 16-bit mode */
 #endif
 
-			eth_pio_write(test, 8192, sizeof(test));
+			eth_pio_write( (unsigned char *) test, 8192, sizeof(test));
 			eth_pio_read(8192, testbuf, sizeof(test));
 			if (!memcmp(test, testbuf, sizeof(test)))
 				break;
@@ -919,7 +920,7 @@ static int eth_probe (struct dev *dev, unsigned short *probe_addrs __unused)
 				D8390_DCR_FT1 | D8390_DCR_LS, eth_nic_base + D8390_P0_DCR);
 			outb(MEM_16384, eth_nic_base + D8390_P0_PSTART);
 			outb(MEM_32768, eth_nic_base + D8390_P0_PSTOP);
-			eth_pio_write(test, 16384, sizeof(test));
+			eth_pio_write( (unsigned char *) test, 16384, sizeof(test));
 			eth_pio_read(16384, testbuf, sizeof(test));
 			if (!memcmp(testbuf, test, sizeof(test)))
 				break;

src/drivers/net/pcnet32.c

@@ -787,7 +787,7 @@ static int pcnet32_probe ( struct nic *nic, struct pci_device *pci ) {
 		ltint = 1;
 	}
 
-	DBG ( "%s at %hX,", chipname, ioaddr );
+	DBG ( "%s at %hX,", chipname, (unsigned int) ioaddr );
 
 	/* read PROM address */
 	for (i = 0; i < 6; i++)
@@ -799,7 +799,7 @@ static int pcnet32_probe ( struct nic *nic, struct pci_device *pci ) {
 	}
 
 	/* Print out some hardware info */
-	DBG ( "%s: IO Addr 0x%hX, MAC Addr %s\n ", chipname, ioaddr,
+	DBG ( "%s: IO Addr 0x%hX, MAC Addr %s\n ", chipname, (unsigned int) ioaddr,
 	      eth_ntoa ( nic->node_addr ) );
 
 	/* Set to pci bus master */

src/drivers/net/r8169.c

@@ -74,12 +74,22 @@ static u32 ioaddr;
 
 
 #ifdef RTL8169_DEBUG
+
+#if 0
 #define assert(expr) \
                if(!(expr)) { printk( "Assertion failed! %s,%s,%s,line=%d\n", #expr,__FILE__,__FUNCTION__,__LINE__); }
+#endif
+
 #define DBG_PRINTF( fmt, args...)   printk("r8169: " fmt, ## args);
+
 #else
+
+#if 0
 #define assert(expr) do {} while (0)
+#endif
+
 #define DBG_PRINTF( fmt, args...)   ;
+
 #endif				// end of #ifdef RTL8169_DEBUG
 
 /* media options 
@@ -904,7 +914,7 @@ static int r8169_probe ( struct nic *nic, struct pci_device *pci ) {
 
 	/* Print out some hardware info */
 	DBG ( "%s: %s at IOAddr %#hX, ", pci->driver_name, eth_ntoa ( nic->node_addr ),
-	       ioaddr );
+	      (unsigned int) ioaddr );
 
 	/* Config PHY */
 	rtl8169_hw_PHY_config(nic);

src/drivers/net/sis900.c

@@ -751,7 +751,8 @@ sis900_init_rxd(struct nic *nic __unused)
         rxd[i].bufptr = virt_to_bus(&rxb[i*RX_BUF_SIZE]);
         if (sis900_debug > 0)
             printf("sis900_init_rxd: rxd[%d]=%p link=%X cmdsts=%X bufptr=%X\n", 
-                   i, &rxd[i], rxd[i].link, rxd[i].cmdsts, rxd[i].bufptr);
+                   i, &rxd[i], (unsigned int) rxd[i].link, (unsigned int) rxd[i].cmdsts,
+		   (unsigned int) rxd[i].bufptr);
     }
 
     /* load Receive Descriptor Register */
@@ -1146,12 +1147,14 @@ sis900_transmit(struct nic  *nic,
         /* wait */ ;
 
     if (currticks() >= to) {
-        printf("sis900_transmit: TX Timeout! Tx status %X.\n", tx_status);
+        printf("sis900_transmit: TX Timeout! Tx status %X.\n", 
+	       (unsigned int) tx_status);
     }
     
     if (tx_status & (ABORT | UNDERRUN | OWCOLL)) {
         /* packet unsuccessfully transmited */
-        printf("sis900_transmit: Transmit error, Tx status %X.\n", tx_status);
+        printf("sis900_transmit: Transmit error, Tx status %X.\n", 
+	       (unsigned int) tx_status);
     }
     /* Disable interrupts by clearing the interrupt mask. */
     outl(0, ioaddr + imr);
@@ -1179,14 +1182,15 @@ sis900_poll(struct nic *nic, int retrieve)
     int retstat = 0;
 
     if (sis900_debug > 2)
-        printf("sis900_poll: cur_rx:%d, status:%X\n", cur_rx, rx_status);
+        printf("sis900_poll: cur_rx:%d, status:%X\n", cur_rx, 
+	       (unsigned int) rx_status);
 
     if (!(rx_status & OWN))
         return retstat;
 
     if (sis900_debug > 1)
         printf("sis900_poll: got a packet: cur_rx:%d, status:%X\n",
-               cur_rx, rx_status);
+               cur_rx, (unsigned int) rx_status);
 
     if ( ! retrieve ) return 1;
     
@@ -1195,7 +1199,7 @@ sis900_poll(struct nic *nic, int retrieve)
     if (rx_status & (ABORT|OVERRUN|TOOLONG|RUNT|RXISERR|CRCERR|FAERR)) {
         /* corrupted packet received */
         printf("sis900_poll: Corrupted packet received, buffer status = %X\n",
-               rx_status);
+               (unsigned int) rx_status);
         retstat = 0;
     } else {
         /* give packet to higher level routine */

src/drivers/net/sundance.c

@@ -611,7 +611,7 @@ static int sundance_probe ( struct nic *nic, struct pci_device *pci ) {
 	DBG ( "Device revision id: %hx\n", sdc->pci_rev_id );
 
 	/* Print out some hardware info */
-	DBG ( "%s: %s at ioaddr %hX, ", pci->driver_name, nic->node_addr, BASE);
+	DBG ( "%s: %s at ioaddr %hX, ", pci->driver_name, nic->node_addr, (unsigned int) BASE);
 
 	sdc->mii_preamble_required = 0;
 	if (1) {

src/drivers/net/tlan.c

@@ -70,7 +70,7 @@ static void TLan_PhyPowerDown(struct nic *nic);
 static void TLan_PhyPowerUp(struct nic *nic);
 
 
-static void TLan_SetMac(struct nic *nic __unused, int areg, char *mac);
+static void TLan_SetMac(struct nic *nic __unused, int areg, unsigned char *mac);
 
 static void TLan_PhyReset(struct nic *nic);
 static void TLan_PhyStartLink(struct nic *nic);
@@ -515,7 +515,7 @@ static int tlan_poll(struct nic *nic, int retrieve)
 
 	nic->packetlen = framesize;
 
-	DBG ( ".%d.", framesize ); 
+	DBG ( ".%d.", (unsigned int) framesize ); 
      
 	memcpy(nic->packet, rxb +
 	       (priv->cur_rx * TLAN_MAX_FRAME_SIZE), nic->packetlen);
@@ -591,7 +591,7 @@ static void tlan_transmit(struct nic *nic, const char *d,	/* Destination */
 
 	if (tail_list->cStat != TLAN_CSTAT_UNUSED) {
 		printf("TRANSMIT: %s is busy (Head=%p Tail=%x)\n",
-		       priv->nic_name, priv->txList, priv->txTail);
+		       priv->nic_name, priv->txList, (unsigned int) priv->txTail);
 		tx_ring[entry].cStat = TLAN_CSTAT_UNUSED;
 //		priv->txBusyCount++;
 		return;
@@ -1300,7 +1300,7 @@ void TLan_MiiWriteReg(struct nic *nic __unused, u16 phy, u16 reg, u16 val)
 *
 **************************************************************/
 
-void TLan_SetMac(struct nic *nic __unused, int areg, char *mac)
+void TLan_SetMac(struct nic *nic __unused, int areg, unsigned char *mac)
 {
 	int i;
 
@@ -1361,8 +1361,8 @@ void TLan_PhyDetect(struct nic *nic)
 		TLan_MiiReadReg(nic, phy, MII_GEN_ID_LO, &lo);
 		if ((control != 0xFFFF) || (hi != 0xFFFF)
 		    || (lo != 0xFFFF)) {
-			printf("PHY found at %hX %hX %hX %hX\n", phy,
-			       control, hi, lo);
+			printf("PHY found at %hX %hX %hX %hX\n", 
+			       (unsigned int) phy, control, hi, lo);
 			if ((priv->phy[1] == TLAN_PHY_NONE)
 			    && (phy != TLAN_PHY_MAX_ADDR)) {
 				priv->phy[1] = phy;

src/drivers/net/tulip.c

@@ -1317,14 +1317,14 @@ static int tulip_probe ( struct nic *nic, struct pci_device *pci ) {
 
     if (inl(ioaddr + CSR5) == 0xFFFFFFFF) {
         printf("%s: The Tulip chip at %X is not functioning.\n",
-               tp->nic_name, ioaddr);
+               tp->nic_name, (unsigned int) ioaddr);
         return 0;
     }
    
     pci_read_config_byte(pci, PCI_REVISION, &chip_rev);
 
     printf("%s: [chip: %s] rev %d at %hX\n", tp->nic_name,
-           tulip_tbl[chip_idx].chip_name, chip_rev, ioaddr);
+           tulip_tbl[chip_idx].chip_name, chip_rev, (unsigned int) ioaddr);
     printf("%s: Vendor=%hX  Device=%hX", tp->nic_name, tp->vendor_id, tp->dev_id);
 
     if (chip_idx == DC21041  &&  inl(ioaddr + CSR9) & 0x8000) {
@@ -1404,7 +1404,8 @@ static int tulip_probe ( struct nic *nic, struct pci_device *pci ) {
     for (i = 0; i < ETH_ALEN; i++)
         last_phys_addr[i] = nic->node_addr[i];
 
-    DBG ( "%s: %s at ioaddr %hX\n", tp->nic_name, eth_ntoa ( nic->node_addr ), ioaddr );
+    DBG ( "%s: %s at ioaddr %hX\n", tp->nic_name, eth_ntoa ( nic->node_addr ), 
+	  (unsigned int) ioaddr );
 
     tp->chip_id = chip_idx;
     tp->revision = chip_rev;

src/drivers/net/via-rhine.c

@@ -890,10 +890,10 @@ MIIDelay (void)
     int i;
     for (i = 0; i < 0x7fff; i++)
     {
-	inb (0x61);
-	inb (0x61);
-	inb (0x61);
-	inb (0x61);
+        ( void ) inb (0x61);
+        ( void ) inb (0x61);
+        ( void ) inb (0x61);
+        ( void ) inb (0x61);
     }
 }
 

src/drivers/net/w89c840.c

@@ -408,7 +408,7 @@ static int w89c840_poll(struct nic *nic, int retrieve)
                 if ((status & 0xffff) != 0x7fff) {
                     printf("winbond-840 : Oversized Ethernet frame spanned "
                            "multiple buffers, entry %d status %X !\n",
-                           w840private.cur_rx, status);
+                           w840private.cur_rx, (unsigned int) status);
                 }
             } else if (status & 0x8000) {
                 /* There was a fatal error. */
@@ -568,7 +568,8 @@ static void w89c840_transmit(
 
     /* Transmit timed out... */
 
-    printf("winbond-840 : transmission TIMEOUT : status %X\n", w840private.tx_ring[entry].status);
+    printf("winbond-840 : transmission TIMEOUT : status %X\n", 
+	   (unsigned int) w840private.tx_ring[entry].status);
 
     return;
 }