Instructions for use of the 3C90X driver for EtherBoot Original 3C905B support by: Greg Beeley (Greg.Beeley@LightSys.org), LightSys Technology Services, Inc. February 11, 1999 Updates for 3C90X family by: Steve Smith (steve.smith@juno.com) October 1, 1999 Minor documentation updates by Greg Beeley (Greg.Beeley@LightSys.org) March 29, 2000 ------------------------------------------------------------------------------- I OVERVIEW The 3c90X series ethernet cards are a group of high-performance busmaster DMA cards from 3Com. This particular driver supports both the 3c90x and the 3c90xB revision cards. 3C90xC family support has been tested to some degree but not extensively. Here's the licensing information: This program Copyright (C) 1999 LightSys Technology Services, Inc. Portions Copyright (C) 1999 Steve Smith. This program may be re-distributed in source or binary form, modified, sold, or copied for any purpose, provided that the above copyright message and this text are included with all source copies or derivative works, and provided that the above copyright message and this text are included in the documentation of any binary-only distributions. This program is distributed WITHOUT ANY WARRANTY, without even the warranty of FITNESS FOR A PARTICULAR PURPOSE or MERCHANTABILITY. Please read the associated documentation "3c90x.txt" before compiling and using this driver. II FLASH PROMS The 3c90xB cards, according to the 3Com documentation, only accept the following flash memory chips: Atmel AT29C512 (64 kilobyte) Atmel AT29C010 (128 kilobyte) The 3c90x cards, according to the 3Com documentation, accept the following flash memory chips capacities: 64 kb (8 kB) 128 kb (16 kB) 256 kb (32 kB) and 512 kb (64 kB) Atmel AT29C512 (64 kilobyte) chips are specifically listed for both adapters, but flashing on the 3c905b cards would only be supported through the Atmel parts. Any device, of the supported size, should be supported when programmed by a dedicated PROM programmer (e.g. not the card). To use this driver in such a PROM, visit Atmel's web site and download their .PDF file containing a list of their distributors. Contact the distributors for pricing information. The prices are quite reasonable (about $3 US each for the 64 kB part), and are comparable to what one would expect for similarly sized standard EPROMs. And, the flash chips are much easier to work with, as they don't need to be UV-erased to be reprogrammed. The 3C905B card actually provides a method to program the flash memory while it is resident on board the card itself; if someone would like to write a small DOS program to do the programming, I can provide the information about the registers and so forth. A utility program, 3c90xutil, is provided with Etherboot in the 'contrib' directory that allows for the on-board flashing of the ROM while Linux is running. The program has been successfully used under Linux, but I have heard problem reports of its use under FreeBSD. Anyone willing to make it work under FreeBSD is more than welcome to do so! You also have the option of using EPROM chips - the 3C905B-TX-NM has been successfully tested with 27C256 (32kB) and 27C512 (64kB) chips with a specified access time of 100ns and faster. III GENERAL USE Normally, the basic procedure for using this driver is as follows: 1. Run the 3c90xcfg program on the driver diskette to enable the boot PROM and set it to 64k or 128k, as appropriate. 2. Build the appropriate 3c90x.fd0 or 3c90x.fd0 floppy image with possibly the value CFG_3C90X_XCVR defined to the transceiver type that you want to use (i.e., 10/100 rj45, AUI, coax, MII). 3. Run the floppy image on the PC to be network booted, to get it configured, and to verify that it will boot properly. 4. Build the 3c90x.rom or 3c90x.lzrom PROM image and program it into the flash or EPROM memory chip. 5. Put the PROM in the ethernet card, boot and enable 'boot from network first' in the system BIOS, save and reboot. Here are some issues to be aware of: 1. If you experience crashes or different behaviour when using the boot PROM, add the setting CFG_3C90X_BOOTROM_FIX and go through the steps 2-5 above. This works around a bug in some 3c905B cards (see below), but has some side-effects which may not be desirable. Please note that you have to boot off a floppy (not PROM!) once for this fix to take effect. 2. The possible need to manually set the CFG_3C90X_XCVR value to configure the transceiver type. Values are listed below. 3. The possible need to define CFG_3C90X_PRESERVE_XCVR for use in operating systems that don't intelligently determine the transceiver type. Some things that are on the 'To-Do' list, perhaps for me, but perhaps for any other volunteers out there: 1. Extend the driver to fully implement the auto-select algorithm if the card has multiple media ports. 2. Fix any bugs in the code .... 3. Extend the driver to support the 3c905c revision cards "officially". Right now, the support has been primarily empirical and not based on 3c905C documentation. Now for the details.... This driver has been tested on roughly 300 systems. The main two configuration issues to contend with are: 1. Ensure that PCI Busmastering is enabled for the adapter (configured in the CMOS setup) 2. Some systems don't work properly with the adapter when plug and play OS is enabled; I always set it to "No" or "Disabled" -- this makes it easier and really doesn't adversely affect anything. Roughly 95% of the systems worked when configured properly. A few have issues with booting locally once the boot PROM has been installed (this number has been less than 2%). Other configuration issues that to check: 1. Newer BIOS's actually work correctly with the network boot order. Set the network adapter first. Most older BIOS's automatically go to the network boot PROM first. 2. For systems where the adapter was already installed and is just having the PROM installed, try setting the "reset configuration data" to yes in the CMOS setup if the BIOS isn't seen at first. If your BIOS doesn't have this option, remove the card, start the system, shut down, install the card and restart (or switch to a different PCI slot). 3. Make sure the CMOS security settings aren't preventing a boot. The 3c905B cards have a significant 'bug' that relates to the flash prom: unless the card is set internally to the MII transceiver, it will only read the first 8k of the PROM image. Don't ask why -- it seems really obscure, but it has to do with the way they mux'd the address lines from the PCI bus to the ROM. Unfortunately, most of us are not using MII transceivers, and even the .lzrom image ends up being just a little bit larger than 8k. Note that the workaround for this is disabled by default, because the Windows NT 4.0 driver does not like it (no packets are transmitted). So, the solution that I've used is to internally set the card's nvram configuration to use MII when it boots. The 3c905b driver does this automatically. This way, the 16k prom image can be loaded into memory, and then the 3c905b driver can set the temporary configuration of the card to an appropriate value, either configurable by the user or chosen by the driver. To enable the 3c905B bugfix, which is necessary for these cards when booting from the Flash ROM, define -DCFG_3C90X_BOOTROM_FIX when building, create a floppy image and boot it once. Thereafter, the card should accept the larger prom image. The driver should choose an appropriate transceiver on the card. However, if it doesn't on your card or if you need to, for instance, set your card to 10mbps when connected to an unmanaged 10/100 hub, you can specify which transceiver you want to use. To do this, build the 3c905b.fd0 image with -DCFG_3C90X_XCVR=x, where 'x' is one of the following values: 0 10Base-T 1 10mbps AUI 3 10Base-2 (thinnet/coax) 4 100Base-TX 5 100Base-FX 6 MII 8 Auto-negotiation 10Base-T / 100Base-TX (usually the default) 9 MII External MAC Mode 255 Allow driver to choose an 'appropriate' media port. Then proceed from step 2 in the above 'general use' instructions. The .rom image can be built with CFG_3C90X_XCVR set to a value, but you normally don't want to do this, since it is easier to change the transceiver type by rebuilding a new floppy, changing the BIOS to floppy boot, booting, and then changing the BIOS back to network boot. If CFG_3C90X_XCVR is not set in a particular build, it just uses the current configuration (either its 'best guess' or whatever the stored CFG_3C90X_XCVR value was from the last time it was set). [[ Note for the more technically inclined: The CFG_3C90X_XCVR value is programmed into a register in the card's NVRAM that was reserved for LanWorks PROM images to use. When the driver boots, the card comes up in MII mode, and the driver checks the LanWorks register to find out if the user specified a transceiver type. If it finds that information, it uses that, otherwise it picks a transceiver that the card has based on the 3c905b's MediaOptions register. This driver isn't quite smart enough to always determine which media port is actually _connected_; maybe someone else would like to take on that task (it actually involves sending a self-directed packet and seeing if it comes back. IF it does, that port is connected). ]] Another issue to keep in mind is that it is possible that some OS'es might not be happy with the way I've handled the PROM-image hack with setting MII mode on bootup. Linux 2.0.35 does not have this problem. Behavior of other systems may vary. The 3com documentation specifically says that, at least with the card that I have, the device driver in the OS should auto-select the media port, so other drivers should work fine with this 'hack'. However, if yours doesn't seem to, you can try defining CFG_3C90X_PRESERVE_XCVR when building to cause Etherboot to keep the working setting (that allowed the bootp/tftp process) across the eth_reset operation. IV FOR DEVELOPERS.... If you would like to fix/extend/etc. this driver, feel free to do so; just be sure you can test the modified version on the 3c905B-TX cards that the driver was originally designed for. This section of this document gives some information that might be relevant to a programmer. A. Main Entry Point a3c90x_probe is the main entry point for this driver. It is referred to in an array in 'config.c'. B. Other Important Functions The functions a3c90x_transmit, a3c90x_poll, a3c90x_reset, and a3c90x_disable are static functions that EtherBoot finds out about as a result of a3c90x_probe setting entries in the nic structure for them. The EtherBoot framework does not use interrupts. It is polled. All transmit and receive operations are initiated by the etherboot framework, not by an interrupt or by the driver. C. Internal Functions The following functions are internal to the driver: a3c90x_internal_IssueCommand - sends a command to the 3c905b card. a3c90x_internal_SetWindow - shifts between one of eight register windows onboard the 3c90x. The bottom 16 bytes of the card's I/O space are multiplexed among 128 bytes, only 16 of which are visible at any one time. This SetWindow function selects one of the eight sets. a3c90x_internal_ReadEeprom - reads a word (16 bits) from the card's onboard nvram. This is NOT the BIOS boot rom. This is where the card stores such things as its hardware address. a3c90x_internal_WriteEeprom - writes a word (16 bits) to the card's nvram, and recomputes the eeprom checksum. a3c90x_internal_WriteEepromWord - writes a word (16 bits) to the card's nvram. Used by the above routine. a3c90x_internal_WriteEepromWord - writes a word (16 bits) to the card's nvram. Used by the above routine. D. Globals All global variables are inside a global structure named INF_3C90X. So, wherever you see that structure referenced, you know the variable is a global. Just keeps things a little neater. E. Enumerations There are quite a few enumerated type definitions for registers and so forth, many for registers that I didn't even touch in the driver. Register types start with 'reg', window numbers (for SetWindow) start with 'win', and commands (for IssueCommand) start with 'cmd'. Register offsets also include an indication in the name as to the size of the register (_b = byte, _w = word, _l = long), and which window the register is in, if it is windowed (0-7). F. Why the 'a3c90x' name? I had to come up with a letter at the beginning of all of the identifiers, since 3com so conveniently had their name start with a number. Another driver used 't' (for 'three'?); I chose 'a' for no reason at all. Addendum by Jorge L. deLyra , 22Nov2000 re working around the 3C905 hardware bug mentioned above: Use this floppy to fix any 3COM model 3C905B PCI 10/100 Ethernet cards that fail to load and run the boot program the first time around. If they have a "Lucent" rather than a "Broadcom" chipset these cards have a configuration bug that causes a hang when trying to load the boot program from the PROM, if you try to use them right out of the box. The boot program in this floppy is the file named 3c905b-tpo100.rom from Etherboot version 4.6.10, compiled with the bugfix parameter CFG_3C90X_BOOTROM_FIX You have to take the chip off the card and boot the system once using this floppy. Once loaded from the floppy, the boot program will access the card and change some setting in it, correcting the problem. After that you may use either this boot program or the normal one, compiled without this bugfix parameter, to boot the machine from the PROM chip. [Any recent Etherboot version should do, not just 4.6.10 - Ed.]