//
// Created by robin on 2/24/17.
//

// When set, _DEBUG co-opts pins 11 and 13 for debugging with an
// oscilloscope or logic analyzer.  Beware: it also slightly modifies
// the bit times, so don't rely on it too much at high baud rates
#define _DEBUG 0
#define _DEBUG_PIN1 11
#define _DEBUG_PIN2 13
//
// Includes
//
#include <avr/interrupt.h>
#include <avr/pgmspace.h>
#include <Arduino.h>
#include "SoftwareSerial8e1.h"
#include <util/delay_basic.h>

//
// Statics
//
SoftwareSerial8e1 *SoftwareSerial8e1::active_object = 0;
uint8_t SoftwareSerial8e1::_receive_buffer[_SS_MAX_RX_BUFF];
volatile uint8_t SoftwareSerial8e1::_receive_buffer_tail = 0;
volatile uint8_t SoftwareSerial8e1::_receive_buffer_head = 0;

//
// Debugging
//
// This function generates a brief pulse
// for debugging or measuring on an oscilloscope.
#if _DEBUG
inline void DebugPulse(uint8_t pin, uint8_t count)
{
  volatile uint8_t *pport = portOutputRegister(digitalPinToPort(pin));

  uint8_t val = *pport;
  while (count--)
  {
    *pport = val | digitalPinToBitMask(pin);
    *pport = val;
  }
}
#else
inline void DebugPulse(uint8_t, uint8_t) {}
#endif

//
// Private methods
//

/* static */
inline void SoftwareSerial8e1::tunedDelay(uint16_t delay) {
    _delay_loop_2(delay);
}

// This function sets the current object as the "listening"
// one and returns true if it replaces another
bool SoftwareSerial8e1::listen()
{
    if (!_rx_delay_stopbit)
        return false;

    if (active_object != this)
    {
        if (active_object)
            active_object->stopListening();

        _buffer_overflow = false;
        _receive_buffer_head = _receive_buffer_tail = 0;
        active_object = this;

        setRxIntMsk(true);
        return true;
    }

    return false;
}

// Stop listening. Returns true if we were actually listening.
bool SoftwareSerial8e1::stopListening()
{
    if (active_object == this)
    {
        setRxIntMsk(false);
        active_object = NULL;
        return true;
    }
    return false;
}

//
// The receive routine called by the interrupt handler
//
void SoftwareSerial8e1::recv()
{

#if GCC_VERSION < 40302
// Work-around for avr-gcc 4.3.0 OSX version bug
// Preserve the registers that the compiler misses
// (courtesy of Arduino forum user *etracer*)
    asm volatile(
    "push r18 \n\t"
            "push r19 \n\t"
            "push r20 \n\t"
            "push r21 \n\t"
            "push r22 \n\t"
            "push r23 \n\t"
            "push r26 \n\t"
            "push r27 \n\t"
    ::);
#endif

    uint8_t d = 0;

    // If RX line is high, then we don't see any start bit
    // so interrupt is probably not for us
    if (_inverse_logic ? rx_pin_read() : !rx_pin_read())
    {
        // Disable further interrupts during reception, this prevents
        // triggering another interrupt directly after we return, which can
        // cause problems at higher baudrates.
        setRxIntMsk(false);

        // Wait approximately 1/2 of a bit width to "center" the sample
        tunedDelay(_rx_delay_centering);
        DebugPulse(_DEBUG_PIN2, 1);

        // Read each of the 8 bits
        for (uint8_t i=8; i > 0; --i)
        {
            tunedDelay(_rx_delay_intrabit);
            d >>= 1;
            DebugPulse(_DEBUG_PIN2, 1);
            if (rx_pin_read())
                d |= 0x80;
        }

        if (_inverse_logic)
            d = ~d;

        // if buffer full, set the overflow flag and return
        uint8_t next = (_receive_buffer_tail + 1) % _SS_MAX_RX_BUFF;
        if (next != _receive_buffer_head)
        {
            // save new data in buffer: tail points to where byte goes
            _receive_buffer[_receive_buffer_tail] = d; // save new byte
            _receive_buffer_tail = next;
        }
        else
        {
            DebugPulse(_DEBUG_PIN1, 1);
            _buffer_overflow = true;
        }

        // skip the parity bit
        tunedDelay(_rx_delay_stopbit);
        DebugPulse(_DEBUG_PIN1, 1);

        // skip the stop bit
        tunedDelay(_rx_delay_stopbit);
        DebugPulse(_DEBUG_PIN1, 1);

        // Re-enable interrupts when we're sure to be inside the stop bit
        setRxIntMsk(true);

    }

#if GCC_VERSION < 40302
// Work-around for avr-gcc 4.3.0 OSX version bug
// Restore the registers that the compiler misses
    asm volatile(
    "pop r27 \n\t"
            "pop r26 \n\t"
            "pop r23 \n\t"
            "pop r22 \n\t"
            "pop r21 \n\t"
            "pop r20 \n\t"
            "pop r19 \n\t"
            "pop r18 \n\t"
    ::);
#endif
}

uint8_t SoftwareSerial8e1::rx_pin_read()
{
    return *_receivePortRegister & _receiveBitMask;
}

//
// Interrupt handling
//

/* static */
inline void SoftwareSerial8e1::handle_interrupt()
{
    if (active_object)
    {
        active_object->recv();
    }
}

#if defined(PCINT0_vect)
ISR(PCINT0_vect)
{
  SoftwareSerial8e1::handle_interrupt();
}
#endif

#if defined(PCINT1_vect)
ISR(PCINT1_vect, ISR_ALIASOF(PCINT0_vect));
#endif

#if defined(PCINT2_vect)
ISR(PCINT2_vect, ISR_ALIASOF(PCINT0_vect));
#endif

#if defined(PCINT3_vect)
ISR(PCINT3_vect, ISR_ALIASOF(PCINT0_vect));
#endif

//
// Constructor
//
SoftwareSerial8e1::SoftwareSerial8e1(uint8_t receivePin, uint8_t transmitPin, bool inverse_logic /* = false */) :
        _rx_delay_centering(0),
        _rx_delay_intrabit(0),
        _rx_delay_stopbit(0),
        _tx_delay(0),
        _buffer_overflow(false),
        _inverse_logic(inverse_logic)
{
    setTX(transmitPin);
    setRX(receivePin);
}

//
// Destructor
//
SoftwareSerial8e1::~SoftwareSerial8e1()
{
    end();
}

void SoftwareSerial8e1::setTX(uint8_t tx)
{
    // First write, then set output. If we do this the other way around,
    // the pin would be output low for a short while before switching to
    // output high. Now, it is input with pullup for a short while, which
    // is fine. With inverse logic, either order is fine.
    digitalWrite(tx, _inverse_logic ? LOW : HIGH);
    pinMode(tx, OUTPUT);
    _transmitBitMask = digitalPinToBitMask(tx);
    uint8_t port = digitalPinToPort(tx);
    _transmitPortRegister = portOutputRegister(port);
}

void SoftwareSerial8e1::setRX(uint8_t rx)
{
    pinMode(rx, INPUT);
    if (!_inverse_logic)
        digitalWrite(rx, HIGH);  // pullup for normal logic!
    _receivePin = rx;
    _receiveBitMask = digitalPinToBitMask(rx);
    uint8_t port = digitalPinToPort(rx);
    _receivePortRegister = portInputRegister(port);
}

uint16_t SoftwareSerial8e1::subtract_cap(uint16_t num, uint16_t sub) {
    if (num > sub)
        return num - sub;
    else
        return 1;
}

//
// Public methods
//

void SoftwareSerial8e1::begin(long speed)
{
    _rx_delay_centering = _rx_delay_intrabit = _rx_delay_stopbit = _tx_delay = 0;

    // Precalculate the various delays, in number of 4-cycle delays
    uint16_t bit_delay = (F_CPU / speed) / 4;

    // 12 (gcc 4.8.2) or 13 (gcc 4.3.2) cycles from start bit to first bit,
    // 15 (gcc 4.8.2) or 16 (gcc 4.3.2) cycles between bits,
    // 12 (gcc 4.8.2) or 14 (gcc 4.3.2) cycles from last bit to stop bit
    // These are all close enough to just use 15 cycles, since the inter-bit
    // timings are the most critical (deviations stack 8 times)
    _tx_delay = subtract_cap(bit_delay, 15 / 4);

    // Only setup rx when we have a valid PCINT for this pin
    if (digitalPinToPCICR(_receivePin)) {
#if GCC_VERSION > 40800
        // Timings counted from gcc 4.8.2 output. This works up to 115200 on
    // 16Mhz and 57600 on 8Mhz.
    //
    // When the start bit occurs, there are 3 or 4 cycles before the
    // interrupt flag is set, 4 cycles before the PC is set to the right
    // interrupt vector address and the old PC is pushed on the stack,
    // and then 75 cycles of instructions (including the RJMP in the
    // ISR vector table) until the first delay. After the delay, there
    // are 17 more cycles until the pin value is read (excluding the
    // delay in the loop).
    // We want to have a total delay of 1.5 bit time. Inside the loop,
    // we already wait for 1 bit time - 23 cycles, so here we wait for
    // 0.5 bit time - (71 + 18 - 22) cycles.
    _rx_delay_centering = subtract_cap(bit_delay / 2, (4 + 4 + 75 + 17 - 23) / 4);

    // There are 23 cycles in each loop iteration (excluding the delay)
    _rx_delay_intrabit = subtract_cap(bit_delay, 23 / 4);

    // There are 37 cycles from the last bit read to the start of
    // stopbit delay and 11 cycles from the delay until the interrupt
    // mask is enabled again (which _must_ happen during the stopbit).
    // This delay aims at 3/4 of a bit time, meaning the end of the
    // delay will be at 1/4th of the stopbit. This allows some extra
    // time for ISR cleanup, which makes 115200 baud at 16Mhz work more
    // reliably
    _rx_delay_stopbit = subtract_cap(bit_delay * 3 / 4, (37 + 11) / 4);
#else // Timings counted from gcc 4.3.2 output
        // Note that this code is a _lot_ slower, mostly due to bad register
        // allocation choices of gcc. This works up to 57600 on 16Mhz and
        // 38400 on 8Mhz.
        _rx_delay_centering = subtract_cap(bit_delay / 2, (4 + 4 + 97 + 29 - 11) / 4);
        _rx_delay_intrabit = subtract_cap(bit_delay, 11 / 4);
        _rx_delay_stopbit = subtract_cap(bit_delay * 3 / 4, (44 + 17) / 4);
#endif


        // Enable the PCINT for the entire port here, but never disable it
        // (others might also need it, so we disable the interrupt by using
        // the per-pin PCMSK register).
        *digitalPinToPCICR(_receivePin) |= _BV(digitalPinToPCICRbit(_receivePin));
        // Precalculate the pcint mask register and value, so setRxIntMask
        // can be used inside the ISR without costing too much time.
        _pcint_maskreg = digitalPinToPCMSK(_receivePin);
        _pcint_maskvalue = _BV(digitalPinToPCMSKbit(_receivePin));

        tunedDelay(_tx_delay); // if we were low this establishes the end
    }

#if _DEBUG
    pinMode(_DEBUG_PIN1, OUTPUT);
  pinMode(_DEBUG_PIN2, OUTPUT);
#endif

    listen();
}

void SoftwareSerial8e1::setRxIntMsk(bool enable)
{
    if (enable)
        *_pcint_maskreg |= _pcint_maskvalue;
    else
        *_pcint_maskreg &= ~_pcint_maskvalue;
}

void SoftwareSerial8e1::end()
{
    stopListening();
}


// Read data from buffer
int SoftwareSerial8e1::read()
{
    if (!isListening())
        return -1;

    // Empty buffer?
    if (_receive_buffer_head == _receive_buffer_tail)
        return -1;

    // Read from "head"
    uint8_t d = _receive_buffer[_receive_buffer_head]; // grab next byte
    _receive_buffer_head = (_receive_buffer_head + 1) % _SS_MAX_RX_BUFF;
    return d;
}

int SoftwareSerial8e1::available()
{
    if (!isListening())
        return 0;

    return (_receive_buffer_tail + _SS_MAX_RX_BUFF - _receive_buffer_head) % _SS_MAX_RX_BUFF;
}

size_t SoftwareSerial8e1::write(uint8_t b)
{
    if (_tx_delay == 0) {
        setWriteError();
        return 0;
    }
//    setTX(_receivePin);

    // By declaring these as local variables, the compiler will put them
    // in registers _before_ disabling interrupts and entering the
    // critical timing sections below, which makes it a lot easier to
    // verify the cycle timings
    volatile uint8_t *reg = _transmitPortRegister;
    uint8_t reg_mask = _transmitBitMask;
    uint8_t inv_mask = ~_transmitBitMask;
    uint8_t oldSREG = SREG;
    bool inv = _inverse_logic;
    uint16_t delay = _tx_delay;
    uint8_t p = 0;
    for (uint8_t t = 0x80; t; t >>= 1)
        if (b & t) p++;

    if (inv)
        b = ~b;

    cli();  // turn off interrupts for a clean txmit

    // Write the start bit
    if (inv)
        *reg |= reg_mask;
    else
        *reg &= inv_mask;

    tunedDelay(delay);

    // Write each of the 8 bits
    for (uint8_t i = 8; i > 0; --i)
    {
        if (b & 1) // choose bit
            *reg |= reg_mask; // send 1
        else
            *reg &= inv_mask; // send 0

        tunedDelay(delay);
        b >>= 1;
    }

    if (p & 0x01)
        *reg |= reg_mask; // send 1
    else
        *reg &= inv_mask; // send 0
    tunedDelay(_tx_delay);

    // restore pin to natural state
    if (inv)
        *reg &= inv_mask;
    else
        *reg |= reg_mask;

    SREG = oldSREG; // turn interrupts back on
    tunedDelay(_tx_delay);

//    setRX(_receivePin);
//    pinMode(_receivePin, INPUT);

    return 1;
}

void SoftwareSerial8e1::flush()
{
    // There is no tx buffering, simply return
}

int SoftwareSerial8e1::peek()
{
    if (!isListening())
        return -1;

    // Empty buffer?
    if (_receive_buffer_head == _receive_buffer_tail)
        return -1;

    // Read from "head"
    return _receive_buffer[_receive_buffer_head];
}